• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.134-134
• /
• 2015

최근 액체 플라즈마에 대한 주된 이슈는 방전에 의해 발생하는 히드록실라디칼(OH-)과 버블이다. 액체 플라즈마를 이용한 다양한 응용분야에서는 히드록실라디칼에 주목하고 있다. 액체 플라즈마는 그래핀 파생물의 용액 친화도 향상을 위해 이용될 수 있다. 흑연이 포함된 과산화수소(H2O2) 용액에서 전기적인 방전으로 만들어진 히드록실라디칼로 그래핀 파생물의 용액 친화도를 향상시킨다. 이는 잠재적인 프린팅(printing) 기술 발전에 기대된다. 그리고 이 라디칼은 폐수에서 발암성의 트라이클로로아세트산(CCl3COOH)을 탈 염소하고 분해하는 역할을 하여 액체 플라즈마가 새로운 수처리 기술로 부상되고 있다. 또한 인체에서는 살균 작용을 하는 것 뿐만 아니라 단백질 고리를 끊는 역할을 하여 전립선 수술과 같은 인체수술에 적용될 수 있다. 최근 액체 플라즈마를 이용한 돼지 각막 임상수술에서 레이저와 필적할 정도로 매우 정밀하게 수술된 연구결과가 발표되어 인체 각막수술 적용에 기대된다. 이처럼 액체 플라즈마를 이용한 대부분의 응용분야에서 히드록실라디칼의 역할이 중요하다. 액체 플라즈마의 또 다른 이슈인 버블은 2가지의 역할을 한다. 첫 번째로 방전소스의 역할이다. 액체 속에 담긴 얇은 전극에 전압을 인가하면 전극 주변에서 강한 전기장의 발생으로 줄열(joule heating)에 의해 버블이 생성된다. 전극에서 버블이 생성되었을 때, 서로 다른 유전율을 가진 두 물질로 나누어진다. (버블 안은 공기로 상대 유전율 ${\varepsilon}r{\fallingdotseq}=1$, 용액은 ${\varepsilon}r{\fallingdotseq}=80$이다.) 시스템에 인가된 전압이 항복 전압(breakdown voltage)을 넘어서면 유전율이 상대적으로 낮은 버블내부에 강한 전기장이 걸리게 되어 방전이 일어난다. 만약 버블이 존재하지 않는다면 방전을 위해서 매우 높은 전압이 필요하다. 따라서 버블은 플라즈마 방전의 소스역할을 한다. 두번째로 버블은 전극의 부식을 방지하는 역할을 한다. 전극 부식은 주로 전기분해로 인한 산화반응에 의해 발생하는데 버블을 전극에 오래 머무르게 하면 부식을 방지할 수 있다. 이처럼 액체 플라즈마 시스템에서 버블의 역할들은 상당히 중요하다. 일반적으로 버블은 시스템에 인가하는 전원, 전극 극성 그리고 전압크기에 따라 거동이 달라진다. 시스템에 AC파워를 인가하면 버블은 주파수가 높을수록 전극에서 떨어지는 속도가 빨라지는 특성을 보인다. 핀 전극 극성이 음극일 때는 양극일 때보다 버블이 더 잘 생성된다. 또한 인가전압크기에 따라 거동이 달라지며 시스템에 같은 전압을 인가하여도 크기가 항상 같지 않고, 거동도 일관성을 보이지 않은 랜덤적인 모습을 보인다. 본 연구에서는 이 랜덤적인 버블의 거동을 정리하고 응용분야에서 중요하게 여기는 히드록실라디칼 생성에 대해 공부하기 위해 염류 용액(saline solution)에 핀(pin)-면(plane) 전극 구조를 설치하여 10Hz 주파수(1% duty cycle)를 가진 0-600V 구형펄스로 실험하였다. 실험을 통한 결과로서 랜덤적인 버블의 거동을 전극에서 버블이 떨어지는 속도와 플라즈마 특성에 따라 슈팅모드(shooting mode)와 유지모드(keeping mode) 2가지 모드로 분류하였다. 슈팅모드에서는 버블이 핀 전극에서 성장하지 못하고 빠른 속도로 떨어지는 모드로 플라즈마 방전이 잘 이루어지지 않는다. 반면 유지모드에서는 버블이 핀 전극에서 떨어지지 않고 지속적으로 성장한다. 이 모드에서는 펄스 시간 동안 하나의 버블로 연속적인 방전이 가능하다. 방전이 일어날 때 발생하는 히드록실라디칼의 생성은 버블 내부의 쉬스와 관련이 있다. 이 라디칼을 만들기 위해서는 높은 에너지가 요구되기 때문에 버블 내부의 쉬스(sheath)에서 만들어진다. 펄스 동안 쉬스는 주로 핀 전극 주변에서 유지되며 히드록실라디칼은 이곳에서 주로 만들어진다. 따라서 버블과 함께 쉬스도 성장하는 버블유지모드에서 슈팅모드보다 히드록실라디칼이 더 많이 생성된다.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.1
• /
• pp.85-90
• /
• 2007

Fenton's Reagent is applied to directly dissolve the cation-exchange resin, IRN-77. The characteristics of the experimental procedure is to dry the resin first and $FeSO_4$ solution is completely absorbed into the resin, and then $H_2O_2$ is introduced later for an effective reaction between the reagents within the resin. An a characteristic of the dissolution, the lag time is needed for about 1 hour until the main reaction is occurred, which was more affected with the less concentration of $FeSO_4$ and the less initial dose of $H_2O_2$. The dose of $H_2O_2$ was equally divided into the early stage and the later stage after the initial reaction to provide an effective and safe reaction condition. The optimum conditions is appeared that the concentration of $FeSO_4$ is 0.9M and the dose of 15% $H_2O_2$ solution is 6-7 volume for the dissolution of unit weight of IRN-77. The effect of the heating on the lag time was checked and the time could be reduced within 5 minutes at $50^{\circ}C$, which is a relatively low temperature. The large amount of the resin, 5g and 10g, was also completely decomposed by increasing the dose of $H_2O_2$ to 9-10 volume ratio.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.5 no.3
• /
• pp.221-227
• /
• 2007

Fenton's reagent is applied to directly decompose the ion-exchange resins, IRN-78 and the mixed resin with IRN-77. The newly applied procedures is to dry the resin first and the catalyst solution is completely absorbed into the resin, then a limited dose of $H_2O_2$ is introduced for an effective reaction between the reagents within the resin. As a characteristic on the decomposition of IRN-78, the resin mixture should be heated to $40^{\circ}C$ to induce the initial reaction and lag time is also needed for about 20 minutes until the main reaction occurs. The effectiveness of the decomposition is investigated using $CuSO_4,\;Cu(NO_3)_2\;and\;FeSO_4$ as a catalyst and the decomposition rate is compared depending on the concentration of each catalyst and the amount of $H_2O_2$. The most effective catalyst was found to be $FeSO_4$ for IRN-78 alone and the mixed resin with IRN-77, and $FeSO_4$ showed a special effect that the reaction was initiated without heating and a lag time. Furthermore, the optimum concentration of the catalyst for each resin and the mixed one is suggested in the view point of the amount of $H_2O_2$ needed and the stability of the decomposition reaction.

• Journal of Energy Engineering
• /
• v.26 no.2
• /
• pp.99-120
• /
• 2017

In SS branch of Korea District Heating Corporation, Combined Heat & Power power plant with 99MW capacity and 98Gcal / h capacity is operated as a district electricity business. In this region, it is difficult to operate the generator due to the problem of surplus heat treatment between June and September due to the economic recession and the decrease in demand, so it is urgent to develop an economical energy new business model. In this study, we will develop an optimized operation model by introducing a renewable energy hybrid system based on actual operation data of this site. In particular, among renewable energy sources, fuel cell (Fuel Cell) power generation which can generate heat and electricity at the same time with limited location constraints, photovoltaic power generation which is representative renewable energy, ESS (Energy Storage System). HOMER (Hybrid Optimization of Multiple Energy Resources) program was used to select the optimal model. As a result of the economic analysis, 99MW CHP combined cycle power generation is the most economical in terms of net present cost (NPC), but 99MW CHP in terms of carbon emission trading and renewable energy certificate And 5MW fuel cells, and 521kW of solar power to supply electricity and heat than the supply of electricity and heat by 99MW CHP cogeneration power, it was shown that it is economically up to 247.5 billion won. we confirmed the results of the improvement of the zone electricity business condition by introducing the fuel cell and the renewable energy hybrid system as the optimization process model.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.2
• /
• pp.16-23
• /
• 2006

This paper presents a novel single-stage high frequency resonant inverter link type DC-DC converter using zero voltage switching with high power-factor. The proposed topology is integrated half-bridge boost rectifier as power factor corrector(PFC) and half-bridge high frequency resonant converter into a single-stage. The input stage of the half-bridge boost rectifier works in discontinuous conduction mode(DCM) with constant duty cycle and variable switching frequency. So that a boost converter makes the line current follow naturally the sinusoidal line voltage waveform. Simulation results have demonstrated the feasibility of the proposed high frequency resonant converter. Characteristics values based on characteristics analysis through circuit analysis is given as basis data in design procedure. Also, experimental results are presented to verify theoretical discussion. This proposed inverter will be able to be practically used as a power supply in various fields as induction heating applications, fluorescent lamp and DC-DC converter etc.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.220-225
• /
• 1998

The spinel structured $LiMn_2O_4$ was prepared from $Li_2CO_3$ and $MnO_2$ by calcination at various temperatures in the range of $750{\sim}900^{\circ}C$. It was found that the most suitable cubic structure of $LiMn_2O_4$ was obtained by heating at $850^{\circ}C$ for 12 hrs. However, in the calcination at $900^{\circ}C$, $Mn^{4+}$ of 0.06M was changed to $Mn^{+3}$ by the oxygen loss, so that it has been shown that the formula has changed to $LiMn_2O_{3.97}$. This phenomena were in agreement with the Jahn-Teller distortion by the increment of $Mn^{+3}$ ion on the octahedral sites of the spinel structured $LiMn_2O_4$. The results showed that after 15 charge/discharge cycles in the voltage range from 3.5V to 4.3V versus Li/$Li^+$ with a current density of $0.25mA/cm^2$, the spinel structured $LiMn_2O_4$ that was prepared at $900^{\circ}C$ showed a lower discharge capacity, 82~50 mAh/g, while the $LiMn_2O_4$, prepared at $850^{\circ}C$, showed the discharge capacity of 102~64 mAh/g.

• Microbiology and Biotechnology Letters
• /
• v.35 no.1
• /
• pp.30-35
• /
• 2007

This study was carried out to investigate the usefulness of the aerial part of Cnidium officinale Makino as a bioactive material source. The aerial part(leaf and stem) of Cnidium officinale Makino was extracted with three kinds of solvents and determined their antimicrobial activities against several bacteria and yeast strains using the paper disc method and the microtiter dilution method. The extracts of the Cnidium offocinale aerial part exhibited the broad spectrum of antibacterial activity against Gram (+) and Gram (-) bacteria, including food-borne pathogens such as Listeria monocytogenes, Salmonella typhimurium, and Staphylococcus aureus. The extracts of Cnidium officinale also showed antifungal activity against Saccharomyces cerevisiae. The ethyl acetate extracts completely inhibited the growth of Staphylococcus aureus and Pseudomonas aerogenes, and moderately inhibited the growth of Escherichia coli and Enterobacter cloacae at the concentration of 0.5 mg/mL. However, water extract of Cnidium officinale exhibited lower antimicrobial activity than ethyl acetate and methanol extracts. The inhibitory effect of the ethyl acetate extract of Cnidium officinale Makino was not destroyed by heating at $100^{\circ}C$ for 30 min or at $121^{\circ}C$... for 15 min. These results suggest that the aerial part of Cnidium officinale Makino could be a useful source for a natural antimicrobial material.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.16 no.3
• /
• pp.339-346
• /
• 2018

A geological repository system consists of a disposal canister with packed spent fuel, buffer material, backfill material, and intact rock. The buffer is indispensable to assure the disposal safety of high-level radioactive waste. Since the heat generated from spent nuclear fuel in a disposal canister is released to the surrounding buffer materials, the thermal properties of the buffer material are very important in determining the entire disposal safety. Especially, since thermal expansion can cause thermal stress to the intact rock mass in the near-field, it is very important to evaluate thermal expansion characteristics of bentonite buffer materials. Therefore, this paper presents a thermal expansion coefficient prediction model of the Gyeongju bentonite buffer materials which is a Ca-bentonite produced in South Korea. The linear thermal expansion coefficient was measured considering heating rate, dry density and temperature variation using dilatometer equipment. Thermal expansion coefficient values of the Gyeongju bentonite buffer materials were $4.0{\sim}6.0{\times}10^{-6}/^{\circ}C$. Based on the experimental results, a non-linear regression model to predict the thermal expansion coefficient was suggested and fitted according to the dry density.

• Analytical Science and Technology
• /
• v.14 no.5
• /
• pp.432-441
• /
• 2001

An automated on-line portable preconcentration-short column gas chromatograph was developed, which used preconcentrator using adsorption tube with Tenax-GR and Curie-point heating. The developed system operated with 3 steps of processing, preconcentration, thermal desorption, and analysis and cleaning, and could continued operating within 1~2 min cycle. The recoveries of preconcentrator for toluene was ranged between $94.7{\pm}6.6%$ and $103.8{\pm}3.1%$ with less than 7% of RSD. For benzene, toluene and xylene(BTX) standard gas test, IDL was 41, 49, $472ng/m^3$ benzene, toluene and o-xylene, respectively. The BTX mixture was analyzed within 30 sec with baseline separation by the system equipped with 4 m long capillary column. The deficiency of separation power caused by short column was solved by the control of sample injection volume and inlet/outlet pressure ratio. The automated portable preconcentration-short column gas chromatograph system was found to be useful for the continuous air monitoring of BTX at ppb levels in ambient air.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.22-28
• /
• 2017

The performance of lithium ion batteries used in electric vehicles (EV) varies greatly depending on the battery temperature. In this paper, the finite difference method was used to evaluate the temperature change, state of charge (SOC), internal resistance, and voltage change of the battery due to heat generation in the battery. The simulation model was linked with AMESim to calculate the driving range of an EV traveling in New European Driving Cycle (NEDC) mode. As the temperature dropped below $25^{\circ}C$, the internal resistance of the battery increased, which increased the amount of heat generated and decreased the driving range of EV. At battery temperatures above $25^{\circ}C$, the driving range was also decreased due to reduced SOC that deteriorated the battery performance. The battery showed optimal performance and the driving range was maximized at $25^{\circ}C$. When battery temperatures of $-20^{\circ}C$ and $45^{\circ}C$, the driving range of EV decreased by 33% and 1.8%, respectively. Maintaining the optimum battery temperature requires heating the battery at low temperature and cooling it down at high temperature through efficient battery thermal management. Approximately 500 W of heat should be supplied to the battery when the ambient temperature is $-20^{\circ}C$, while 250 W of heat should be removed for the battery to be maintained at $25^{\circ}C$.