• Korean Journal of Food Science and Technology
• /
• v.23 no.1
• /
• pp.44-51
• /
• 1991

The thermal resistance of the important microorganisms in takju. Korean traditional turbid alcoholic beverage, was measured and optimun heating time and temperature to achieve the commercial pasteurization of these microorganisms were examined. Most of the vegetative bacterial cells in takju were destroyed by heating at over $60^{\circ}C$, except for the spore forming organisms, which did not actively grow in takju after pasteurization. The important microorganisms for the quality deterioration of pasteurized takju were then appeared to be yeast and molds, and their thermal resistances were measured. The thermal resistances of these microorganisms changed greatly depending upon the heating method. The D values of yeast in takju were 3.5 min at $65^{\circ}C$ and 0.46 min at $80^{\circ}C$ in cap-tube, and 7.1 sec at $65^{\circ}C$ and 2.3 sec at $80^{\circ}C$ in a continuous coil heat exchanger. Those of molds were 2.7 min at 65℃ and 0.25 min at $80^{\circ}C$ in cap-tube, and 3 sec at $65^{\circ}C$ and <1 sec at $80^{\circ}C$ in the coil heat exchanger. The acidity and pH did not change at $30^{\circ}C$ for two weeks after pasteurization by heating in the coil heat exchanger at $65^{\circ}C$ for 17 sec, but the viscosity increased slightly by the heat treatment. Significant differences in sensory quality, especially the formation of burnt smell and bitterness by heating takju for 12D of yeast at $70,\;80\;and\;85^{\circ}C$, respectively, were observed and this resulted in the significant reduction in overall likeness of pasteurized takju. However, when the heating temperature was fixed to $80^{\circ}C$, the overall likeness of pasteurized takju did not affected significantly by the heating time ranging from 8D to 12D of yeast. It was concluded that the optimum pasteurization condition of takju in a continuous heat exchanger was heating at $80^{circ}C$ for 23sec(10D of yeast).

• Solar Energy
• /
• v.12 no.1
• /
• pp.15-24
• /
• 1992

An hourly simulation model of a solar LiBr-water absorption cooling and heating system (for brevity, solar absorption system) is presented, based on SuperCalc spreadsheet computational procedures. This paper demonstrates the value of using spreadsheet simulation techniques by examining the thermal performances of a solar absorption system. The hourly heating and cooling coil loads for a typical office building in Tucson, Arizona are modeled and calculated using ASHRAE methods. The details of the algorithms for the components and control schemes are presented. Two case studies are also presented using real system parameters.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.164-165
• /
• 2017

본 논문은 직렬 공진형 컨버터를 이용하여 낮은 저항을 갖는 주방 용기를 가열하기 위한 유도 가열(Induction Heating; IH)용 공진형 컨버터와 코일 설계방법을 제안한다. 기존 IH 시스템은 저항이 작은 용기를 가열할 때 낮은 전압이득으로 인해 정격보다 큰 전류가 흘러 스위칭 손실 및 전도 손실이 증가하고 소자의 정격 전류량을 초과하는 문제가 발생한다. 본 논문에서는 용기에 따른 임피던스를 분석하고 다양한 저항 조건의 용기를 모두 가열하기 위한 적절한 IH용 코일 설계 방법을 제안한다. 이는 2.4 kW의 최대 전력을 가지는 IH용 공진형 컨버터 시작품을 사용하여 제안하는 설계의 타당성을 검증하고자한다.

• Journal of the Korean Society of Safety
• /
• v.36 no.2
• /
• pp.10-17
• /
• 2021

This paper presents the robust design of each component used in the development of an induction bolt heating system for dismantling the high-temperature high-pressure casing heating bolts of turbines in power plants. The induction bolt heating system comprises seven assemblies, namely AC breaker, AC filter, inverter, transformer, work coil, cable, and CT/PT. For each of these assemblies, the various failure modes are identified by the failure mode and effects analysis (FMEA) method, and the causes and effects of these failure modes are presented. In addition, the risk priority numbers are deduced for the individual parts. To ensure robust design, the insulated-gate bipolar transistor (IGBT), switched-mode power supply (SMPS), C/T (adjusting current), capacitor, and coupling are selected. The IGBT is changed to a field-effect transistor (FET) to enhance the voltage applied to the induction heating system, and a dual-safety device is added to the SMPS. For C/T (adjusting current), the turns ratio is adjusted to ensure an appropriate amount of induced current. The capacitor is replaced by a product with heat resistance and durability; further, coupling with a water-resistant structure is improved such that the connecting parts are not easily destroyed. The ground connection is chosen for management priority.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.1037-1039
• /
• 2002

가전산업과 연계하여 유도가열 기술을 응용한 대표적인 시스템으로 IH압력밥솥을 예로 들 수 있다. 유도가열 코일에서 고주파 자속의 의해 발생된 와전류가 결합된 밥솥을 가열하기 때문에 유도가열 코일에는 고주파 손실을 줄이기 위해 Litz wire가 사용된다 이에 본 논문은 특히 IH압력밥솥에 사용되는 Litz wire를 선정하는 데 있어 중요한 요소가 되는 소선경, 가닥수별 AC DC 저항 및 손실계산 그리고 Cost 예측 방법을 제안한다.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.97-99
• /
• 1994

Energy saving electric fan heater that uses driving part as heating part is different from general fan heater. As it uses energy that drives rotor and generate heat at the same coil. it is simpler and cheaper than fan heater. In this study, shaded-pole motor that is low cost and simple in spite of low efficiency was used for th fan heater.

• Proceedings of the SAREK Conference
• /
• 2003.07a
• /
• pp.214-214
• /
• 2003

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2000.11a
• /
• pp.257-260
• /
• 2000

The composite composed of glass fabric and BMI resin was fabricated using resin transfer molding(RTM) process. it will be used as a supporting plate of transformer coil for high speed train. To develop a RTM process, permeability of preform was measured and resin properties like a viscosity and gellation time were checked. A resin pre-heating system and a mold system were also designed and developed. Using a vacuum-assisted RTM process, the composite supporting plate was successfully fabricated.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.1035-1037
• /
• 1993

Thermo motor that uses driving part as heating part is different from general fan heater. As it uses energy that drives rotor and generate heat at the same coil, it is simpler and cheaper than general fan heater. In this study, shaded-pole motor was used that is low cost and simple in spite of low efficiency.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.4
• /
• pp.740-746
• /
• 2009

Two step serial load induction superheater has been proposed using resonance type induction heat method in this paper. Heat method is a type of flowing the electron induction and current to special alloy heater in body from external heat coil with non-contact method. Inverter was a full bridge serial load resonance type and inductor was used as load in LC resonance design to maximize the efficiency. The developed system is a new heat exchanging method combined with electromagnetic induction heater and fluid movement, ana very accurate to control of heating the gas, liquid and evaporated mass, so on without combustion process.