• 한국주조공학회지
• /
• 제39권2호
• /
• pp.26-31
• /
• 2019

In this study, the mechanical characteristics and microstructure of hypereutectic Al-17Si-5Fe extruded alloys prepared by a rapid solidification process (RSP) were investigated. The hypereutectic Al alloy was fabricated by means of RSP and permanent casting. For RSP, the Al alloy melted at $920^{\circ}C$, cooling the specimens at a rate of $10^6^{\circ}C/s$ when the RSP was used, thus allowing the refining of primary Si particles more than when using permanent casting, at a rate of about 91%. We tested an extrusion RSP billet and a permanent-cast billet. Before the hot-extrusion process, heating to $450^{\circ}C$ took place for one hour. The samples were then hotextruded with a condition of extrusion ratio of 27 and a ram speed of 0.5 mm/s. Microstructural analyses of the extruded RSP method and the permanent casting method were carried out with OM and SEM-EDS mapping. The mechanical properties in both cases were evaluated by Vickers micro-hardness, wear resistance and tensile tests. It was found that when hypereutectic Al-17Si-5Fe alloys were fabricated by a rapid solidification method, it becomes possible to refine Si and intermetallic compounds. During the preparation of the hypereutectic Al-17Si-5Fe alloy by the rapid solidification method, the pressure of the melting crucible was low, and at faster drum speeds, smaller grain alloy flakes could be produced. Hot extrusion of the hypereutectic Al-17Si-5Fe alloy during the rapid solidification method required higher pressure levels than hot extrusion of the permanent mold-casted alloy. However, it was possible to produce an extruded material with a better surface than that of the hot extruded material processed by permanent mold casting.

• Korean Chemical Engineering Research
• /
• 제60권4호
• /
• pp.620-629
• /
• 2022

가열 속도, 몰 공간속도, 질화반응온도 등 다양한 실험 조건을 변화하며 바나디움 산화물과 암모니아와의 승온 질화반응을 통하여 바나디움 산화질화물을 제조하여 특성분석을 수행하였으며 제조된 바나디움 산화질화물 상에서 암모니아 분해반응의 촉매 활성을 검토하였다. 제조된 촉매의 물리·화학적 특성을 알아보기 위하여 N₂ 흡착분석, X-선 회절분석(XRD), 수소 승온환원(H₂-TPR), 산소 존재 하 승온산화 (TPO), 암모니아 탈착 (NH₃-TPD), 투과전자현미경(TEM) 분석을 수행하였다. 340 ℃에서 5 m² g^-1의 낮은 비표면적을 갖는 V₂O₅의 환원에 의하여 V₂O₃ 으로의 변환은 미세 기공 형성에 의해 115 m² g^-1 높은 비표면적 값을 보여주었으며 그 이상의 질화반응 온도가 증가함에 따라 소결현상에 의해 지속적인 비표면적의 감소를 초래하였다. 비표면적에 가장 큰 영향을 미치는 질화반응 변수는 반응온도였으며, 단일 상의 VN_xO_y의 x + y 값은 질화반응온도가 증가함에 따라 1.5에서 1.0으로 근접하였으며 680 ℃의 높은 반응온도에서 입방 격자상수 a는 VN 값에 근접하였다. 본 실험 조건 중에 질화반응온도가 가장 높았던 680 ℃에서 암모니아 전환율은 93%로 나타났으며 비활성화는 관찰되지 않았다.

• Nuclear Engineering and Technology
• /
• 제25권1호
• /
• pp.91-101
• /
• 1993

가압경수로형 원자로의 정상 비정상 운전시의 열수력학적 거동을 예측하기 위해서는 원자로내기포계수의 분포를 정확히 계산하는 것이 필수적이다. 이러한 기포계수의 정확한 예측을 위하여 많은 모델들이 제시되었다. 이중 drift-flux모델은 그 계산의 정확성과 간결성에 의하여 널리 사용되고 있다. 이러한 drift-flux 모델을 사용하여 보다 더 정확한 기포계수를 예측하기 위해서는 각 상간의 슬립률과 flow regime 에 따른 기포의 운동의 변화가 정확히 고려되어야 한다. Drift-flux 모델에서는 이러한 두 가지 요소가 drift-flux parameter인 $C_{o}$ 와 (equation omitted), 에서 고려된다. 본 연구에서는 이러한 $C_{o}$ 의 실험적 결정을 위하여 원자로 노심을 모사한 4개의 전열봉이 있는 비등이 발생하는 수직사각 유로를 구성하였으며, 완성된 유로내에서 기포계수의 분포 및 기포속도의 분포를 측정하였다. 국부적 기포계수 및 기포속도 분포의 측정에 사용된 방법은 이중탐침법이며 측정이 이루어진 유로내의 유동 상태는 유속이 비교적 느린 low flow rate condition이며 유로내 압력은 3기압 이하이다. 본 실험에서는 액상의 속도는 측정되지 않았으며, 따라서 $C_{o}$ 의 계산을 위하여 (equation omitted)의 실험 상관관계식을 사용하여 유로내 평균 기포계수의 함수로 나타내었다.

• 한국식품위생안전성학회지
• /
• 제38권3호
• /
• pp.89-98
• /
• 2023

현재, 국내에서는 가공식품인 식용유지에 대한 잔류농약 허용기준이 설정되어 있지 않아 잔류농약은 식용유 품질평가의 사각지대라 할 수 있다. 본 연구에서는 식용유지에서 가열증류법을 이용하여 68종의 농약을 대상으로 추출 및 정제법을 최적화하여 GC-MS/MS 분석법을 확립하였다. 가열증류법은 가열온도 및 시간의 영향을 받았으며 이동상의 역할을 하는 질소의 유량과 용출용매의 종류에는 큰 영향을 받지 않는 것으로 나타났다. 본 연구에서 잔류농약의 결정계수(R²)는 0.99 이상으로 나타났고, 정량한계(LOQ)는 0.01-0.02 mg/L이었으며, 대두유를 이용하여 0.01, 0.02, 0.1, 0.5 mg/L 수준으로 회수율 실험 결과 평균 회수율(n=5)은 66.1-120.0%이었고 상대표준편차는 ±10%이하로 나타났다. 또한 실험실내 일간정밀도는 11%이하로 조사되어, 식품의약품안전평가원의 '식품등 시험법 마련 표준절차에 관한 가이드라인(2016)'에 적합한 수준임을 확인하였다. 따라서 본 연구에서 개발한 시험법은 식용유지의 잔류농약 안전관리를 위한 시험법으로 활용이 가능할 것으로 기대된다.

• 한국학교보건학회지
• /
• 제11권2호
• /
• pp.171-187
• /
• 1998

In recent years, adolescent issues including smoking, drinking, drug abuse, juvenile delinquency, deviant sexual behavior, mental health problems, high suicide rate, juvenile delinquency and absence without due notice, etc are emerging as serious social problems and the debate on these controversial issues is heating up. The previous studies on adolescent health behavior and social juvenile delinquency such as run-away from home and absence without due notice have been conducted mostly by cause analysis utilizing social demographic factors or biological factors. In other words, the main factors analyzed were demographic and economic factors or parent's educational level, etc, which were the fixed environmental ones that were unable to cause the change in the health behavior. Accordingly, the purpose of this study is to analyze factors which are changeable and fixable among the factors influencing the adolescent's health behavior and misconducts and, eventually influencing factors which can be used as the basis to establish health policies and health promotion program to reduce the health risk behavior and misconducts of adolescents. The study subjects were selected by dividing senior high school student in Seoul by region and through random sampling. The 890 subjects were selected from 10 schools including the preparatory school, vocational schools and institutional schools. The duration of the study was for July 1-5, 1997 for the first survey and the second one, for August 25-September 10. Regarding the analysis method, the SAS program was used. The adoptablity of theoretical model was tested through covariance structural analysis utilizing PC-LISREL 8.12 Program. The major findings of the study are as follows: As a result of establishing the model of factors influencing health behavior and juvenile delinquency, in case of male students as the health behavior self-efficacy, education level of fathers, economic level, self-control and the health interest of parent were higher, students were more likely to practice the health promoting behavior. Juvenile delinquency and health risk behavior were prevalent among those with the less shyness, the lower health behavior self-efficacy, lower self-control, lower self-assertiveness, lower economic level. The self-control was the most powerful factor. In case of female students, those with higher health behavior self-efficacy were more likely to practice the health promoting behavior whereas those with lower health behavior self-efficacy, lower self-control, lower self- assertiveness, less shyness were more likely to practice health risk behavior and juvenile delinquency. In case of prep schools, those with higher health behavior self-efficacy and better perceived health status were more likely to practice the health promoting behavior while those with less shyness, lower health behavior self-efficacy and lower academic achievement were more likely to engage in health risk behavior and juvenile delinquency. In case of vocational schools, as health behavior self-efficacy and economic level were higher, the practice rate of health promoting behavior was higher. As the self-control, shyness, self-assertiveness, health behavior self-efficacy were lower, the rate of health risk behavior and juvenile delinquency were higher. In case of social institutional schools, as, the health behavior self-efficacy, social support and economic level, health interest of parents were higher, the rate of health promoting behavior were higher. As the self-control, shyness, self-assertiveness, health behavior self-efficacy and social support were lower, the rate of health risk behavior and juvenile delinquency were higher. So the health promoting behavior was positively related to the health behavior self-efficacy, health interest of parents, social support, education level of fathers, level of perceived health status, economic level. The health risk behavior and juvenile delinquency were higher with the lower health behavior self-efficacy, self-control and self-assertiveness, lower health locus control, less shyness and loneliness, lower economic level and academic achievement. In conclusion, the health risk behavior and juvenile delinquency can be reduced by enhancing self-control, self-assertiveness, health behavior self-efficacy and social support. According to the final model drawn by connecting health behavior and juvenile delinquency, the reduction of health risk behavior can greatly contribute to decreasing social juvenile delinquency as the process of juvenile delinquency was extended from common behaviors to problem behaviors and further into juvenile delinquency.

• 한국학교ㆍ지역보건교육학회지
• /
• 제1권1호
• /
• pp.11-43
• /
• 2000

The purpose of this study was, through analyzing the previous researches, to grasp the present status of environment of school building(ESB), research the sundry records of each element and, through comparative analysis of the standard of ESB in Korea, the United States, and Japan, select the normative standard of ESB, to clarify the point at issue presented in Regulation of Construction & facility Management for Elementary and and Secondary School in Korea, and to suggest an alternative preliminary standard of ESB. To carry out a research for this purpose, these were required: 1. to investigate the existing present status of ESB, 2. to make a comparative analysis of the standard of ESB in each country, 3. to suggest the normative standard of preliminary standard of ESB, 4. to analyze the controversial points of the standard of ESB in Korea, 5. to suggest an alternative preliminary standard of ESB. The conclusions were as follows: 1. Putting, through analyzing the previous researches, the existing present status of ESB together, it seemed that lighting environment, indoor air environment and noise environment were all in poor conditions. 2. In the result of a comparative analysis of the standard of ESB in Korea, Japan and the United States, in Korea the factors of each lighting and indoor air environment were not presented properly, in Japan, in lighting environment aspect, the standard on natural lighting and the factors on brightness were not presented., and in the USA the essential factors of each environment were throughly presented. In the comparison of the standards on each factor, Korea showed that the standard level presented was less properly prescribed than those of the USA and Japan but it also showed that the standard levels prescribed in the USA and in Japan were mostly similar to the standard levels in records investigated. 3. With the result of the normative standard selection on School Builiding environment factor of prescribed in this study, the controversial points of the standard of ESB in Korea were analyzed and the result was utilized to suggest new preliminary standard of ESB. 4. As the result of the analysis of the controversial points of the standard of ESB in Korea, it was found that the standard of ESB in Korea should be established on a basis of School Health Act and be concretely presented in School Health Regulation and School Health Rule. The factors of each environment was improperly presented in the existing standard of ESB in Korea. Moreover the standard of them was inferior to that of the records investigated and those of in the USA and in Japan and it also showed that the standard of it in Korea was improper to maintain Comfortable Learning Environment. 5. A suggested preliminary standard of ESB acquired through above study as follows: 1) In this study a new kind of preliminary standard of ESB is divided into lighting environment, indoor air environment, noise environment, odor environment and for above classification, reasonable factor and standard should be established and the controling way on each standard and countermeasures against it should be considered. 2) In lighting environment, the factors of natural lighting are divided into daylight rate, brightness, glare. In the standard on each factor, daylight rate should secure 5% of a mean daylight rate and 2% of a minimum daylight rate, brightness ratio of maximum illumination to minimum illumination should be under 10:1, and in glare there should not be an occurrence factor from a reflector outside of the classroom. And the factors of unnatural lighting are illumination, brightness, and glare. In the standard on each factor, illumination should be 750 lux or more, brightness ratio should be under 3 to 1, and glare should not occur. And Optimal reflection rate(%) of Colors and Facilities of Classroom which influences lighting environment should be considered. 3) In indoor air environment factors, thermal factors are divided into (1) room temperature, (2) relative humidity, (3) room air movement, (4) radiation heat, and harmful gases (5) CO, (6) $CO_2$ that are proceeded from using the heating fuel such as oval briquettes, firewood, charcoal being used in most of the classroom, and finally (7) dust. In the standard on each factor, the next are necessary; room temperature: $16^{\circ}C{\sim}26^{\circ}C$(summer : $E.T18.9{\sim}23.8^{\circ}C$, winter: $E.T16.7{\sim}21.7^{\circ}C$), relative humidity: $30{\sim}80%$, room air movement: under 0.5m/sec, radiation heat: under $5^{\circ}C$ gap between dry-bulb temperature and wet-bulb temperature, below 1000 ppm of ca and below 10ppm of $CO_2$, dust: below 0.10 $mg/m^3$ of Volume of dust in indoor air, and ventilation standard($CO_2$) for purification of indoor air : once/6 min.(about 7 times/40 min.) in an airtight classroom. 4) In the standard on noise environment, noise level should be under 40 dB(A) and the noise measuring way and the countermeasures against it should be considered. 5) In the standard on odor environment, odor level under Physical Method should be under 2 degrees, and the inspecting way and the countermeasures against it should be considered.

• 한국농공학회지
• /
• 제18권1호
• /
• pp.4038-4051
• /
• 1976

This study was intended to provide the basic design creteria for the refrigerated storage, and to estimate the required optimum capacity of refrigerator for the different sizes and kinds of the existing fruit storage. The structural characteristics of the existing fruit storages in Pyungtaek-khun of Kyungki-do were surveyed. The average out-door air temperature during the expected storage life after harvesting, was obtained by analyzing the weather information. The heat transfer rates through the different models of storage walls were estimated. The refrigerating load required for different models of fruit storage was analyzed in the basis of out-door air temperature. The results obtained in this study are summarized as follows: 1. The fruit storages surveyed were constructed on-ground, under-ground and sub-ground type buildings. The majority of them being the on-ground buildings are mostly made of earth bricks with double walls. Rice hull was mostly used as the insulating materials for their walls and ceilings. About 42% of the buildings were with the horizontal ceiling, 22% with sloped ceiling, and about 36% without ceiling. About 60% of the storage buildings had floor without using insulated material. They were made of compacted earth. 2. There is no difference in heat transfer among six different types of double walls. The double wall, however, gives much less heat transfer than the single wall. Therefore, the double wall is recommended as the walls of the fruit storage on the point of heat transfer. Especially, in case of the single wall using concrete, the heat transfer is about five time of the double walls. It is evident that concrete is not proper wall material for the fruit storage without using special insulating material. 3. The heat transfer through the storage walls is in inverse proportion to the thickness of rice hull which is mostly used as the insulating material in the surveyed area. It is recommended that the thickness of rice hull used as the insulating material far storage wall is about 20cm in consideration of the decreasing rate of heat transfer and the available storage area. 4. The design refrigerating load for the on-ground storages having 20 pyung area is estimated in 4.07 to 4.16 ton refrigeration for double walls, and 5.23 to 6.97 ton refrigeration for single walls. During the long storage life, however, the average daily refrigerating load is ranged from 0.93 to 0.95 ton refrigeration for double walls, and from 1.15 to 1.47 ton refrigeration for single walls, respectively. 5. In case of single walls, 50.8 to 61.4 percent to total refrigerating load during the long storage life is caused by the heat transferred into the room space through walls, ceiling and floor. On the other hand, 39.1 to 40.7 percent is for the double walls. 6. The design and average daily refrigerating load increases in linear proportion to the size of storage area. As the size increases, the increasing rate of the refrigerating load is raised in proportion to the heat transfer rate of the wall. 7. The refrigerating load during the long storage life has close relationship to the out-door air temperature. The maximum refrigeration load is shown in later May, which is amounted to about 50 percent to the design refrigerating load. 8. It is noted that when the wall material having high heat transfer rate, such as the single wall made of concrete, is used, heating facilities are required for the period of later December to early February.

• 농촌의학ㆍ지역보건
• /
• 제12권1호
• /
• pp.5-27
• /
• 1987

It is widely recognized that primary health care in the community is one of the most important and effective health measures in these days. However, it is reality that unsatisfactory health care system, ineffective utilization of health care by the community people in the rural area are hampering better understanding for primary health care. Therefore promoting health for the rural people and increasing understanding about primary health care, the baseline survey in the community focused in examination for safe community water supply was carried out. The survey was conducted through August 25-31, 1986 in order to find out health problems and relevant factors and to define the demographic characteristics of $^*$Sanpuk village, Kumsa-Myun, Yuju-Gun, Kyunggi-Do, Korea. Household survey was carried out for every home by trained interviewers. The major results are found out as follows : 1) 84.2%(400 houses) of total households were surveyed because 15.8%(75 houses) were unable to survey due to either refusal against interview or absence of family. These 400 households were composed of 1,697 residents(male:830, female 867). Educational level of respondents showed 34.1% as elementary school graduated. Religion distribution showed Buddism(23.8%) as the most dominant. 50.7% of respondents married in the area. 2) Most households(91.5%) have lived in their own house in Sanpuk area. Average family size showed 4.3. More than half of residents(64.2%) have used public supplied water tap. Only 1.5% of the households had a flush toliet. The rest of households have still used primitive insanitary latrines. 3) 32.5% of residents have used gas burner for cooking and for heating in the house, and the coal briquet were used for boiler. Lack of convenient public transportation was the chief complaint for their day life. 4) Each household occupied 1,990 pyungs of rice paddy and 1,170 pyungs of ordinary field in average. Beside farming products, mushroom was the highest product. 5) Sixth percent of households in the survey area regularly participated in community meeting one hand and on the other hand 39.5% never participated. Most of respondents closely contacted with their neighbours and they seemed very friendly each other. 6) The prevalence rate of illness and injury during recent 15 days showed 48.3 per 1,000. The prevalence rate of chronic illnesses during the past one year showed 74 per 1,000. Injury and accident lead the higher portion(22.0%) in the former and in the latter pain(arthritis, back-pain) showed 27.0% as the dominant sickness. 87.8% of the ill residents in the former received medical treatment. As the most frequently utilized medical facility, the clinic or hospital were counted. Among the residents suffering from chronic illnesses, 77.3% in Sanpuk area get some kind of medical treatments and they rarely utilized the clinic or hospital. The reason why the patient did not receive any medical care was found out the fact that symptoms of illness was light or mild and economic problems was serious. 7) Average age of marriage showed 21.6 years old in the women and the average duration of marital period was shown for 15.1 years. The married woman in reproductive age in Sanpuk area had experienced pregnancies 4 times in the aver-age including 0.7 time of pregnancy in average were interrupted by induced abortion and 0.3 time by spontaneous abortion respectively. The practicing rate of the family planning of the married woman during reproductive ages showed 70.7% and the tuballigation was found out as the most frequently used contraceptives. 8) Among woman who has children under 2 years old, 70.0% had received the prenatal care for the last pregnancy. However, the average number of prenatal care visitis per woman showed 3.3 times. Fifty-two % of woman who received the postnatal care for the last delivery showed only 37.5%. 9) Immunization rate of the children under 2 years old showed relatively high and looked successful. The breast feeding for these children showed dominantly in the most. Most of the mothers in Sanpuk area had started the supplementary diet during weaning period of their infants of 6th and 7th month after birth. * : Sanpuk area is a demstration area for community development which has been supported by the Community Development Foundation during the part 10 years. The village is relatively closer to urban area such as Seoul, However, it has a similar characteristics shown as a remote village because of geographical location and inconvenient transportation at present.

• 생물환경조절학회지
• /
• 제22권2호
• /
• pp.182-187
• /
• 2013

밀폐된 식물공장 환경에서 환경 조절 및 에너지 소비예측을 위해서는 환경요소들의 변화 요인을 파악해야 한다. 식물체는 광합성 과정에서 많은 양의 물을 증산을 통해 대기 중으로 방출하게 되는데, 일반적으로 식물공장의 특성상 비교적 높은 습도 유지가 필요하며, 증산은 실내 습도에 직접적인 영향을 주기 때문에 식물의 증산량에 대한 정량화가 필요하다. 본 연구에서는 식물공장 생육조건에서 4가지 품종의 상추를 재배하면서 생육기간에 따른 엽면적 변화와 증산속도를 측정하고 이를 바탕으로 Penman-Monteith 방정식을 식물공장 조건에 맞게 변형시켰다. 그리고 이러한 결과들을 토대로 식물공장에서 재배 기간 중 증산으로 인해 발생하는 수분의 양을 시뮬레이션을 통해 예측하였다. 그 결과 작물의 엽면적과 증산속도는 생육기간이 진전됨에 따라 점차 증가하는 것으로 나타났으며 엽면적과 증산량 사이는 비례관계를 나타냈다. 증산량 추정 모델식 변형은 일반적으로 다양한 환경 요인들에 의해 증산량이 결정되던 기존의 모델식들에 비해 엄밀한 환경 요소들에 대한 제어가 가능한 식물공장에서 증산량은 환경 요소들은 상수로 취급 가능하며, 작물의 엽면적지수의 변화에 대해서만 주로 결정되었다. 또한 설정된 환경 조건에서 생육기간에 따른 증산량 추정모델을 이용하여 전체 생육기간 중 작물 개체당 누적 증산량을 높은 결정계수($r^2$)로 예측할 수 있었다. 이렇게 예측된 증산량은 식물공장 환경 제어 기술 중 냉난방 부하 계산 및 관수 계획을 세우는데 활용 가능할 것이다.

• 유기물자원화
• /
• 제20권4호
• /
• pp.106-117
• /
• 2012

건조과정에서 시료의 순환과 낙하이동에 따른 건조효과를 평가하기 위하여 음식물류폐기물 8,000kg을 간접건조방식의 건조기에 투입하고 회전스크류 가동시와 미가동시에 대하여 수분함량, 건조율, 평균입자크기 및 입도분포, 증발수분량 및 건조효율을 비교하였다. 음식물류폐기물의 초기 수분함량은 77.1%로서, 회전스크류 가동시에는 가동 후 5시간 만에 수분함량이 14.4%로 낮아진 반면에 미가동시에는 16시간을 가동시켜도 수분함량 35.6%에 머물고 있어 시료의 순환과 낙하이동이 건조효과 상승에 영향을 미치고 있음을 알 수 있다. 건조시작 후 점성구간 도달 이전에는 입자크기가 증가하면서 수분증발률은 최대치를 보인다. 점성구간에서는 입자크기가 최대치를 나타내나 수분증발률은 급감하기 시작하며, 점성구간 이후에는 입자크기와 수분증발률이 동시에 감소하는 것으로 나타났다. 이는 자유수 증발량과 각 구간에서의 점성차이에 기인한 것으로 여겨진다. 평균 입자크기는 가동 후 지속적으로 증가하여 점성구간인 수분함량 70%-60% 범위에서 최대치를 보인 후 감소하는 경향을 나타내었으나 평균 입자크기의 변화정도는 회전스크류 가동방식에 따라 다르게 나타났다. 또한 회전스크류 가동시 입도분포는 25.0mm에서 0.25mm까지 폭넓게 분포하는 반면에 미가동시에는 25.0mm에서 3.56mm까지 의 좁은 입도분포와 25.0mm이상의 입자크기에 집중되고 있다. 회전스크류 가동으로 건조효율에 미치는 효과를 회전스크류 미가동시와 비교하면 시간당 증발수분량은 364%, DS(Dry Solid)당 증발수분량은 356%나 증가한 것으로 평가되었다.