• Korean Journal of Optics and Photonics
• /
• v.20 no.5
• /
• pp.266-271
• /
• 2009

We designed a thermo-optic switch based on a directional coupler with not only a high extinction ratio but also significantly low power consumption. The switch operates by using the thermo-optic effect of the polymer which the refractive index changes by heating the electrode. If the electrode is not powered (OFF), the input light will be coupled completely to the other waveguide. When the electrode is powered at a certain level (ON), input light launched into the input waveguide will remain in that waveguide due to the lower index adjusted in the other waveguide. The switch based on the directional coupler was designed using the generalized extinction ratio curve and the lateral shift of the input waveguide. The coupling length is 1,610 ${\mu}m$ and the extinction ratios are -28 and -30 dB for ON and OFF states, respectively. The electrode structures were optimized by thermal analysis. The transported heat into the waveguide is increased, as the electrode width (w) is increased and the center distance between the electrode and the waveguide (d) is decreased. Also, because the heat generated in the electrode affects the other waveguide, the temperature difference between two waveguides is varied as the given w and d. There are specific conditions which have the maximum of the temperature difference. That of the temperature difference is increased as the width and the temperature of the electrode are increased. Especially, when the switch is designed using the condition with the maximum of the temperature difference for switching, the temperature of the electrode can be decreased. We expect this condition will be the novel method for the reduction of the power consumption in a thermo-optic switch.

• Korean Journal of Plant Resources
• /
• v.27 no.1
• /
• pp.60-71
• /
• 2014

This study was conducted to identify the potential of rape stalk as a raw material for biorefinery process of rape flower. At first, rape stalk (RS) was immersed in distilled water (DW), acetic acid (AA), oxalic acid (OA), sulfuric acid (SA) and sodium hydroxide (SH) solutions, and the content of reducing sugars liberated from immersed RS was analyzed. Glucose, xylose, arabinose and sucrose were detected varying with the immersion type. In particular, 1% AA-immersion of RS for 72 hr was the most effective conditions to liberate glucose from RS. Secondly, the RS residues were used for elementary analysis and fabrication of fuel pellets. In addition to the solution type, concentration of immersion solutions (0%, 1%, 2%) and immersion time (24, 72, 120 hr) were used as experimental factors. The contents of nitrogen, sulfur and chlorine reduced effectively through the immersion of RS in DW, AA and OA solutions. For properties of RS-based pellets, bulk density and higher heating value of RS-based pellets greatly increased with the immersion of RS, and the qualities were much higher than those of the A-grade pellet of the EN standards. Ash content decreased remarkably through the immersion of RS, and was satisfied with the A-grade pellet standard. Durability was negatively affected by the immersion of RS, and did not reached to B-grade of the EN standard. In conclusion, acid immersion of RS can be a pretreatment method for the production of fuel pellet and bioethanol, but use of the immersed RS for the production of high-quality pellets might be restricted due to low durability of immersed-RS pellets. Therefore, further studies, such as investigation of detailed immersion conditions, fabrication of mixed pellets with wooden materials and addition of binders, are needed to resolve the problems.

• Korean Journal of Food Science and Technology
• /
• v.35 no.4
• /
• pp.635-641
• /
• 2003

A non-thermal pasteurization technology, high Pulsed Electric Field (PEF) has been thought to be a new alternative processing technology instead of heating. The objective of this study was to examine and compare the effect of PEF and High Temperature Short Time (HTST) treatments on the physicochemical, microbiological and sensory characteristics of citrus juices. Total sugar and titratable acidity values of fresh citrus juice and two treatments were not significantly different each other at p<0.05. The concentration of vitamin C in fresh citrus juice $(31.2{\pm}0.59\;mg%)$ was not significantly different with the value of PEF treatment $(29.4{\pm}0.75\;mg%)$ but was significantly higher than the value of HTST treatment $(27.4{\pm}0.75\;mg%)$. The color values (L, a, and b) in PEF treatment were significantly lower than the fresh citrus juice, but were higher than the values of HTST treatment. Both total bacterial cell counts $(6.65\;{\pm}\;0.08\;log_{10}(cfu/mL))$ and yeast counts $(7.79{\pm}0.07\;log_{10}(cfu/mL))$ in fresh citrus juice were significantly reduced by PEF $(1.39{\pm}0.14,\;2.42{\pm}0.1\;log_{10}(cfu/mL))$ as well as HTST treatment (0, 0). PE activity of fresh citrus juice $(1.3{\pm}0.12\;units/mL)$ was significantly reduced by PEF treatment $(0.11{\pm}0.01\;units/mL)$ and was totally inactivated by HTST treatment. Sensory evaluation scores in flavor, taste and overall acceptability between the fresh and PEF treated citrus juices $(7.2{\sim}7.5)$ were not significantly different but the values of HTST treatment $(5.1{\sim}5.8)$ were lower than others. Consequently, PEF treatment is thought to be a good alternative pasteurization method for fresh citrus juice to HTST treatment due to its strong pasteurization effect, reduced destruction of nutrients and good sensory characteristics.

• Korean Chemical Engineering Research
• /
• v.56 no.2
• /
• pp.261-268
• /
• 2018

To prepare mesoporous $TiO_2$ ($meso-TiO_2$) with anatase and rutile crystal structures, hydrothermal and template synthesis were used. $Meso-TiO_2$ with anatase structure was obtained by hydrothermal synthesis. The crystal structure of $meso-TiO_2$ by hydrothermal synthesis converted from anatase to rutile by simple heating at $600^{\circ}C$ and above. However, their mesopore structure collapsed due to phase transition. To prepare $meso-TiO_2$ with rutile structure, template synthesis method was applied using mesoporous silica KIT-6 as a template. Once we incorporated anatase $TiO_2$ inside mesopores of silica, the phase transition temperature of $TiO_2$ confined inside KIT-6 was much higher ($900^{\circ}C$) than that of free-standing $TiO_2$ ($600^{\circ}C$). The suppression of $TiO_2$ phase transition inside mesopores of KIT-6 is closely related with the interaction between $TiO_2$ surface and silica walls in KIT-6 because oxygen vacancy in $TiO_2$ is regarded as the starting point for phase transition. After removal of silica template by NaOH solution washing, $meso-TiO_2$ with mixed phase between anatase and rutile was obtained.

• Food Science and Preservation
• /
• v.18 no.6
• /
• pp.993-997
• /
• 2011

The aims of this research were to determine the proximate composition of various salts and to compare two digestion methods (direct digestion without heating, and microwave digestion) for the determination of the main mineral contents of various salts. Twelve salt samples were divided into three groups of four samples each (imported, Korean gray, and Korean white salts). As a result, the NaCl contents of the Korean white, Korean gray, and imported salts were 85.1, 89.3, and 91.3%, respectively. The salts in the three groups were analyzed for their main mineral contents via AAS. The sodium (Na) content of the Korean white salt was found to be slightly lower than that of the imported salt while the magnesium (Mg) and potassium (K) contents of the Korean white salt were found to be higher than those of the imported salt. The mineral composition (% Na:Mg) obtained using microwave-assisted digestion procedures, and the other dissolutions for the subsequent sample analysis, were 89:1 (for both the imported and Korean gray salts) and 82:3 vs. 81:3 (Korean white salt), respectively. The data regarding the mineral contents and composition of the sun-dried salts obtained through the analysis method of wet digestion and the dissolution procedure were compared, and no significant difference was found between the two datasets. Consequently, in this paper, a direct dissolution procedure is suggested for the analysis of the mineral composition of salt.

• Korean Journal of Remote Sensing
• /
• v.38 no.6_2
• /
• pp.1607-1622
• /
• 2022

The purpose of this study is to determine the actual performance of cool roof in preventing absorbed solar radiation. The spatial correlation between surface temperature and absorbed solar radiation is the method by which the performance of a cool roof can be understood and evaluated. The research area of this study is the vicinity of Jangyu Mugye-dong, Gimhae-si, Gyeongsangnam-do, where an actual cool roof is applied. FLIR Vue Pro R thermal infrared sensor, Micasense Red-Edge multi-spectral sensor and DJI H20T visible spectral sensor was used for aerial photography, with attached to the drone DJI Matrice 300 RTK. To perform the spatial correlation analysis, thermal infrared orthomosaics, absorbed solar radiation distribution maps were constructed, and land cover features of roof were extracted based on the drone aerial photographs. The temporal scope of this research ranged over 9 points of time at intervals of about 1 hour and 30 minutes from 7:15 to 19:15 on July 27, 2021. The correlation coefficient values of 0.550 for the normal roof and 0.387 for the cool roof were obtained on a daily average basis. However, at 11:30 and 13:00, when the Solar altitude was high on the date of analysis, the difference in correlation coefficient values between the normal roof and the cool roof was 0.022, 0.024, showing similar correlations. In other time series, the values of the correlation coefficient of the normal roof are about 0.1 higher than that of the cool roof. This study assessed and evaluated the potential of an actual cool roof to prevent solar radiation heating a rooftop through correlation comparison with a normal roof, which serves as a control group, by using high-resolution drone images. The results of this research can be used as reference data when local governments or communities seek to adopt strategies to eliminate the phenomenon of urban heat islands.

• Nuclear Engineering and Technology
• /
• v.56 no.4
• /
• pp.1526-1531
• /
• 2024

¹³¹I is a fission product produced in a nuclear reactor by irradiating tellurium dioxide, with a half-life of 8.02 day. The most important and widely used method for making ¹³¹I is irradiation using a nuclear reactor and post-irradiation followed by dry distillation. The advantage of the dry distillation process is that the process and the equipment are relatively simple, namely TeO₂ (m.p. 750 ℃), which can withstand heating during reactor irradiation. Based on TeO₂ irradiation by neutron following the technique of dry distillation was explained for production of ¹³¹I on a large scale. A dry distillation followed the radioisotope production operation using the 30 MW GA Siwabessy nuclear reactor to meet national demand. TeO₂ targets are 25 and 50 g irradiated for 87-100 h. The resulting ¹³¹I activity is 20.29339-368.50335GBq. According to the requirements imposed on the radionuclide purity of the preparation, the contribution of ¹³¹I training in the resulting preparation was not less than 99.9 %

• Journal of Korean Society of Forest Science
• /
• v.41 no.1
• /
• pp.7-18
• /
• 1979

Almonds are one of the oldest sources of food and oil for man as used the ice cream, candy, roast, salting, chocolate, breads, backed, cookies, and flavoring ect. So, we wish to plant Almond in our country at the most parts of mountains. In this purpose we must be find out of both root stock of more compatibility and new techniques of grafting was rather simples as compared with the many steps of machinary involved today. This investigation has been carried out to reveral compatibility and practical controls of environment effectives involved in the occurence of each difference combination results in interspecific grafting of Almonds on the root stock of Prunus mandshurica and Prunus persica as materials during the 9 months period from March to November in 1978. With these selected scions were 4 varieties of Almond employing as the Hal1's hardy, Nonpareil, and Thompson grafted in the polyethylene green house with almost identical provision made for effective controls of automatical supplying to heating and mistsprayers as the $22{\sim}25^{\circ}C$ of temperature and 70~90% humidity. Following results have been obtained. Those environmental controls were more effective and practical to grafting unions and success by means veneer-grafting at the green house. 1. Hall's hardy Almond grafted on the root stock of Prunus persica was more compatibility than Prunus mandshurica. 2. The survival percentages as follows of the 95.33% of Hall's hardy/Prunus persica and 92.66% of Hall's hardy/Prunus mandshurica. And those were no significant between root stock of both species. 3. The 3 varieties of sweet Almond grafted on the root stock of P. mandshurica. And those were no significant between root stock of both species. 4. And the survival percentages as fellows. Thompson 92.66%, Nonpareil 90.66% and Kapareil 89.33% those grafted on the root stock of Prunus persica. 5. And then the survival percentage of interspecific grafts on the root Prunus mandshurica as follows of the materials of Thompson 89.66%, Nonpareil 87%, Kapareil 85%. 6. The analysis of variance were no significant among the interactions between 3 varieties Almond and 2 species of root stock plants. 7. And the growth of interspecific grafts of the high 161cm, diameter 12.3mm and length of roots 21.5cm growth as the Hall's hardy Almond grafted on the root stock of Prunus persica. 8. The root stock plants of Prunus mandshurica more effected to 6~8 days early developed leafing of scions and dark green colour than the Prunus persica. 9. The identical provision of automatic systems was more effective to graft unions and grafting process. 10. The veneer-grafting method at the green house was more effective and practical method for the mass production of Almond grafts.

• Parasites, Hosts and Diseases
• /
• v.28 no.4
• /
• pp.241-252
• /
• 1990

In a basic attempt to develop the prophylactic and therapeutic measures on intestinal giantcystic disease of the Israel carp, C), prinks carpio nudum, the effects of physical and chemical factors on viability or survival of the spores of Thelchcnellus kiteuei were checked in vitro by means of extrusion test on the polar filament. When the fresh spores suspended with 0.45% and 0.9% scdium chloride solution and distilled water were laid at $5^{\circ}C$ and $28^{\circ}C$ for short terms, the extrusion rates increased until the 3rd day, meanwhile when son;e of them were suspended with Tyrode's solution at $-70^{\circ}C$ the rates increased gradually until the 8th day. Viabilities of the spores suspended with 0.9% saline and added antibiotics to the suspension at $5^{\circ}C$ for long terms lasted for 997 days and 1, 256 days (presumed values) at maximum, respectively. The spores suspended with distilled water at $28^{\circ}C$ for long terms survived 152.4 days, but the spores suspended with Tyrode's solution at $-70^{\circ}C$ for long terms showed almost the same viable pattern as early freezing stages up to 780 days. The spores suspended with Tyrode's solution, frozen at $-70^{\circ}C$ and thawed at $5^{\circ}C$, showed the highest rate of extrusion of the polar filament. In the case of frozen spores, the extrusion rates during heating tend to become higher in accordance with the increase of frozen period, and the critical points of 180 day-frozen spores to be killed were generally 78.5 hr. at $60^{\circ}C$, 23.4 hr. at $70^{\circ}C$, 189.1 min. at $80^{\circ}C$ or 10.5 min. at $90^{\circ}C$. The longer the spores were frozen, the more time was needed for the death of spores after thawing; 20 days-17.4 days, 100 days-33.2 days, and 400 days-37.8 days. The longer the spores were frozen, the more time was needed for the death of spores at a conventional when they were dried air drying condition, 540 days-23.5 days, 160 days-21.0 days, and 20 days-14.4 days. On the other hand, the longer the spores were frozen, the more spores were dead rapidly when they were irradiated with 10W UV-ray; 100 days-26.0 hr, 300 days-21.9 hr, and 540 days-13.9 hr. The time needed for killing 200 days-frozen spores by various disinfectants at 1, 000 ppd was 5.2 min. by calcium oxide, 10.4 min. by potassium permanganate, 27.8 min. by malachite green and 14.3 hr. by formalin. Transient inhibitory effects of the extrusion of the polar filament were observed by various antiprotozoal and antifungal agents in the descending order of ketoconazole. metronidasole and dapsone. The above results presume that full drying, followed by spraying CaO and maintaining sunny condition for a few days on the concrete bottoms of knish farm may be an effective method for the prevention of intestinal giant.cystic disease.