• 설비공학논문집
• /
• 제16권1호
• /
• pp.54-61
• /
• 2004

The purpose of this study is to improve of energy performance in school buildings. Many building renovations have mainly focused on commercial buildings and houses, but school buildings have no attention in this field although there are many buildings that show degraded energy performance and there are many old fashioned buildings which need renovation. This study was carried out through the survey, field study, energy simulation and life cycle cost analysis. The results of this study can be summarized as follows: In model building, large amount of heat were lost at the building envelope, such as non-insulated skins, window-sills and window-frame joints. According to the simulation result, about 15％ of heating energy is saved by the insulating works compared to pre-renovation condition. Also, LCC analysis revealed to be more effective to select a exteria wall insulation such as a dryvit system.

• Journal of Welding and Joining
• /
• 제20권3호
• /
• pp.98-104
• /
• 2002

A study on microstructures of welds for Zircaloy-4 sheath end closure by the resistance upset welding methods was carried out. Two upset welding process variations such as magnetic farce and multi-impulse resistance welding were used. Grain size and microhardness across welds were analysed in terms of welding parameters. Magnetic farce resistance weld with one cycle of unbalanced mode has smaller upset length and $\alpha-grain$ size in heat affected zone than those of multi-impulse resistance weld because of lower heat input and shorter welding time. Heat affected zone formed by two upset resistance welding variations revealed fine Widmanstatten structure or martensitic ${\alpha}'$ structure due to the high heating rate and foster cooling rate. Magnetic force resistance welds showed recrystallized grains before grain growth, whereas multi-impulse resistance welds showed full grain growth.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 춘계학술발표 개요집
• /
• pp.91-93
• /
• 1995

A study was made to examine the effects of post-weld heat treatment (PWHT) on the toughness and microstructures in the weld heat-affacted zone(HAZ) of Cu-bearing HSLA-100 steel. The Gleeble thermal/mechanical simulator was used to simulate the weld HAZ. The behavior of Cu-precipitates in HAZ is similar to that in base plate. PWHT at 55$0^{\circ}C$ shows highest hardness and lowest toughness, whereas PWHT at $650^{\circ}C$ shows reasonable toughness. Cu precipitated during agcing for increasing the strength of base metal is dissolved during single thermal cycle to 135$0^{\circ}C$ and is precipitated little on cooling and heating during subsequent weld thermal cycle. It precipitates by introducing PWHT.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.350-351
• /
• 2007

The $LiFePO_4$ as cathode materials for lithium ion batteries was synthesized by the solid-state reaction using ballmiller and employed one step heat treatment at $650^{\circ}C$. The influence of the heating time on the structure, particle size and cycle performance was investigated. $LiFePO_4$ heated at $650^{\circ}C$ for 3 h exhibited higher discharge capacity of 140 mAh/g and excellent cycle performance.

• Journal of Welding and Joining
• /
• 제10권3호
• /
• pp.26-39
• /
• 1992

Diffusion bonding of Mo was performed by using the metallic coating of Cu and Cr on the surface to be bonded. Joint characteristics of Mo with or without coating layer were compared in metallurgical and fractograpical aspects. The results showed that the diffusion bonding with coating layer, especially with Cu coating, increased the bending strength of joint. Variation of heating cycle(elevation of temperature for a moment) did not affect significantly the mechanical properties of joint. Fractographical analysis showed that the fracture of joint bonded with Cr coating occurred at the coating layer, while that with Cu coating occurred at the base metal.

• 설비공학논문집
• /
• 제12권3호
• /
• pp.244-250
• /
• 2000

An air source heat pump using liquid injection technique, which can be applied for very low temperature climate, has been simulated to examine the design options. Comparison between the simulation and experiment has been carried out to validate the simulation method. Effects of various design parameters such as liquid injection rate and injection pressure are Investigated to optimize the performance of the heat pump. Finally, optimal liquid infection rate and injection pressure to maintain sufficient heating capacity and moderate discharge refrigerant temperature are suggested when the heat pump was operated at very low outdoor temperature.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1999년도 하계 학술대회 논문집
• /
• pp.104-111
• /
• 1999

증기압축식 열펌프시스템은 그림 1에 나타난 바와 같이 증발기에서의 흡열과 응축기의 방열을 냉난방에 이용할 수 있으며, 공기를 열원으로 할 때는 공기 중 저밀도의 에너지를 고밀도의 에너지로 전환하여 이용할 수 있으며 지중 온도의 연중변화가 적은 점을 이용하여 지열을 열원으로 할 때는 공기를 열원으로 할 경우에 필요한 제상 장치(defrost cycle)가 필요 없게 되고, 압축기 부하도 줄어들게 되어 열펌프 수명이 길어지게 되며 경제성을 확보할 수 있을 것으로 기대된다. (중략)

• 접착 및 계면
• /
• 제3권1호
• /
• pp.20-23
• /
• 2002

The wetting properties of an uncured epoxy resin on both clean and oiled, galvanised steel have been studied. Since the polymer is very viscous at ambient temperature, and also with an aim to simulate industrial conditions, the spreading of drops of resin during a heating cycle (temperature increase at $10^{\circ}C/min$) was recorded and analysed. On clean steel, a contact angle, ${\theta}$, vs time, t, plot shows sigmoidal behaviour, whereas on the oiled substrate, spreading almost ceases in an intermediate stage. This strange behaviour is attributed to significant oil absorption by the polymer.

• 한국산림과학회지
• /
• 제99권4호
• /
• pp.597-602
• /
• 2010

산림탄소순환마을 조성을 위한 가장 기본적인 사항은 온실가스 배출에 관한 통계인데 현재 시 도 단위의 온실가스 배출 통계는 존재하나 마을단위의 온실가스 배출에 관한 통계가 없다. 따라서 본 연구에서 마을단위의 온실가스 배출량에 대한 자료를 구축하여 탄소순환마을의 탄소수지에 관한 모델을 제시하고자 하였다. 연구수행결과, 시범대상지인 경상북도 봉화군 춘양면 서벽리의 에너지사용에 따른 이산화탄소 배출량은 $1,755tCO_2$이며 그 중 난방 사용에 의한 배출량이 55%로 가장 많은 비중을 차지하며 전력 23%, 차량 22%의 순으로 나타났다. 벼농사와 가축 등 농업으로 인해 총 $572tCO_2$의 이산화탄소가 배출되었다. 이는 에너지 사용과 농업부문에서 발생하는 이산화탄소 총 배출량 $2,327tCO_2$의 약 24.5%를 차지했다. 또한, 모델지역에서 사용되는 난방에너지를 우드칩이나 펠릿 등 목재 바이오에너지로 대체할 경우 년간 약 1,580 ton의 목재가 소비될 것이며 난방에서 발생하는 이산화탄소배출량은 $964tCO_2$의 1/12인 $80tCO_2$로 $884tCO_2$ 만큼의 탄소가 저감 될 것으로 예상된다.

• 설비공학논문집
• /
• 제27권1호
• /
• pp.44-49
• /
• 2015

Ceiling cooling and heating system that consider load arrangement and space in the ceiling needs to be developed. Therefore, experimental and economic changes were done to verify the performance of compact type VAV. The test results were as follow. 1) Noise test result, measuring approximately 50.4 dB~56.6 dB (before ceiling in landfill), had a better ceiling deadline than the current measure, about a 10 dB noise reduction, so that the office baseline (40~50 dB) noise was judged to be less than test. 2) For the static pressure test result, taking out an outside hydrostatic 25 mmAq, 24.8 mmAq was measured, respectively, at the point. 3) For the life-cycle cost analysis result, the initial investment cost, maintenance replacement costs, and maintenance costs increased 0.2%, but the energy savings ratio was 19.5% while the whole life cycle savings of 40 years LCC was reduced 11.9%.