• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.75-77
• /
• 2013

In this study, the characteristics of temperature history was evaluated for three hot wires with different capacity installed in slab concrete which are relatively thin. Results can be summarized as follows. First, for the case of material using 5W hot wire, all decreased to below zero at or around 24 hours. Similarly, the material using 20W hot wire decreased to 2℃ below zero at or around 80 hours but satisfied the accumulative temperature of 45° D·D at 7 days of material age. On the other hand, the case of 30W hot wire, the biggest capacity, showed the high temperature history of 5℃ in average at all areas except the corners. Thus, the target accumulative temperature was secured at or around the 3 days of material age. Considering the above, the initial damage by freezing can be prevented only if 20W or higher hot wires are used for the slabs at -10℃ of extremely low temperature environment.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.1
• /
• pp.1-12
• /
• 1996

The fully developed tubulent momentum and heat transfer induced by the square- ribbed roughness elements on both the inner and outer wall surfaces in the concentric annuli are studied analytically based on a modified turbulence model. Heat transfer coefficients for two conditions, i.e, a) inner wall heated as constant heat flux and outer wall insulated b) inner wall insulated and outer wall heated as constant heat flux, are investigated. The analytical results of the fluid flow are verified by experiment. The experiment is done with a pitot tube and a X-type hot wire anemometer to measure the time mean velocity profiles, zero shear stress positions, maximum velocity profiles and friction factors, and etc. The resulting momentum and heat transfer are discussed in terms of various parameters, such as the radius ratio, the relative roughness, the roughness density, Nusselt number and Prandtl number.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2004.04a
• /
• pp.127-139
• /
• 2004

The process of papermaking involves water removal on the paper machine wire, in the press section and in the dryer section. In the dryer section, liquid water in the wet web is removed mainly by evaporation. In conventional machine this is achieved by passing the web over a number of steam heated dryer rolls. A drying process of paper on a heated cylinder roll calculated based on a 1-dimensional model which concerns unsteady heat and mass transfer in the direction of paper thickness. In this study, Prediction of moisture contents average paper sheet temperature and volume fraction along a series of cylinder. Independently, developed models is compared using the same reference data. The model is implemented in CFD code, FLUENT, using user-define-function(UDFs).

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.267-271
• /
• 2000

The local heat transfer rate of an axisymmetric submerged air jet impinging on normal to a heated flat plate was investigated experimentally with varying solidity of mesh screen. The mean velocity and turbulent Intensity profiles of streamwise velocity component were measured using a hot-wire anemometry. The temperature distribution on the heated flat surface was measured with thermocouples. The screen installed in front of the nozzle exit(behind of 35mm) modify the jet flow structure and local heat transfer characteristics. For higher solidity screen, turbulence intensity at core lesion is high and increases the local heat transfer rate at nozzle-to-plate spacings(L/D<6). For larger nozzle-to-plate spacings(L/D>6), however, the turbulent Intensities of all screens tested in this study approach to an asymptotic curve, but the small mean velocity at the core region reduces the local heat transfer rate for high solidity screens.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.3
• /
• pp.52-58
• /
• 2008

The importance of. identifying the causes of electrical faults cannot be overstated because of the accidents caused by over-current that take place at the home, the office and electrical facilities due to misuse, poor products and system faults. It is necessary to gather objective, scientific data pertaining to electrical fault investigation in a product liability(PL) environment. To date, no database(DB) has been built concerning the accurate cause analysis of faultyfacilities. In this paper, accident hazard and arc scattering when over-current flows in copper wire was investigated. It was found that when over-current flows in a copper wire, the copper wire became heated and bent and beads were scattered around the wire with a flash. It was determinedthat the fusing current and time was related to the current rise per second. For example, when the current rise per second was largethe fusing current was higher than when the current rise per second was small, and the beads dispersed along a wide area. Fusing time, however, was shorter. The possibility of electrical fault became highest when the fusing current was higher. As the current rise per second is short, the dendrite structure is distributed in the surface of the copper wire. These experimental results can be utilized for a fault process DB system in the investigation and the prevention of electrical faults.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.96.2-96.2
• /
• 2010

The surface morphology and structural properties of polycrystalline silicon (poly-Si) films made in-situ aluminum induced crystallization at various substrate temperature (300~600) was investigated. Silicon films were deposited by hot-wire chemical vapor deposition (HWCVD), as the catalytic or pyrolytic decomposition of precursor gases SiH4 occurs only on the surface of the heated wire. Aluminum films were deposited by DC magnetron sputtering at room temperature. continuous poly-Si films were achieved at low temperature. from cross-section TEM analyses, It was confirmed that poly-Si above $450^{\circ}C$ was successfully grown on and poly-Si films had (111) preferred orientation. As substrate temperature increases, Si(111)/Si(220) ratio was decreased. The electrical properties of poly-Si film were investigated by Hall effect measurement. Poly-Si film was p-type by Al and resistivity and hall effect mobility was affected by substrate temperature.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.863-868
• /
• 2004

Reheating furnace is an essential facility of a rod mill plant where a billet is heated to the required rolling temperature so that it can be milled to produce wire. Sometimes, it is also necessary to control a transient billet temperature pattern according to the material characteristics to prevent a wire from breaking. Though it is very important objective to obtain a correct information of a billet temperature during furnace operation. Consequently, a billet temperature profile must be estimated. In this paper, a billet heat transfer model based on FEM (Finite Element Method) with spatially distributed emission factors is proposed and a measurement is also carried out for two different furnace operation conditions. Finally, the difference between the model outputs and the measurements is minimized by using the new optimization algorithm named uDEAS(Univariate Dynamic Encoding Algorithm for Searches) with multi-step tuning strategy. Hence, the information of billet temperatures can be obtained by using proposed model on various furnace operation conditions.

• Nuclear Engineering and Technology
• /
• v.38 no.8
• /
• pp.753-762
• /
• 2006

In this paper, works related to enhancement of the CHF are reviewed in terms of fundamental mechanisms and practical applications. Studies on CHF enhancement in forced convection are divided into two categories, CHF enhancement of internal flow in tubes and enhancement of CHF in the nuclear fuel bundle. Methods of enhancing the CHF of internal flows in tubes include enhancement of the swirl flow using twisted tapes, a helical coil, and a grooved surface; promotion of flow mixing using a hypervapotron; altering the characteristics of the heated surface using porous coatings and nano-fluids; and changing the surface tension of the fluid using additives such as surfactants. In the fuel bundle, mixing vanes or wire wrapped rods can be employed to enhance the CHF by changing the flow distributions. These methods can be applied to practical heat exchange systems such as nuclear reactors, fossil boilers, fusion reactors, etc.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.56 no.1
• /
• pp.37-44
• /
• 2007

This paper describes characteristics for copper oxide growth of polyvinyl chloride(PVC) insulated wires by series arc. In this experiment, 600V IV wires were used, and characteristics of oxide growth and ignition process were analyzed in case load was 300W, 460W and 600W, respectively. In the result of experiment, covering materials were molten, carbonized and ignited, whereas, oxidized materials were grown in conducting material. During copper oxide was growing, contact voltages and power dissipations increased. When there is copper oxide growth, the waveform of current showed sinusoidal waveform, and the waveform of voltage showed modified waveform. Oxidized materials were heated at about $905^{\circ}C$, surface structure showed irregular shapes, and cross-section showed multiple cracks. And, the results of this experiment were applied to the fire cause analysis of fire evidence collected at the fire scene.

• Solar Energy
• /
• v.15 no.2
• /
• pp.39-46
• /
• 1995

Reported is a visual and quantitative experimental study on the two-phase flow and heat transfer characteristics of miniature two-phase closed thermosyphons with wire inserts. The visual study clearly demonstrated the two-phase flow involved in such thermosyphons. In the quantitative study, the effects on the heat transfer rate of the insert wire diameter, the ratio of heated-length to cooled length and the applied heat flux were investigated.