• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.255-268
• /
• 2018

Subsea tunnel can be highly vulnerable to seawater intrusion due to unexpected high-water pressure during construction. An artificial ground freezing (AGF) will be a promising alternative to conventional reinforcement or water-tightening technology under high-water pressure conditions. In this study, the freezing energy and required time was calculated by the theoretical model of the heat flow to estimate the total amount of refrigerant required for the artificial ground freezing. A lab-scale freezing chamber was devised to investigate changes in the thermal and mechanical properties of sandy soil corresponding to the variation of the salinity and water pressure. The freezing time was measured with different conditions during the chamber freezing tests. Its validity was evaluated by comparing the results between the freezing chamber experiment and the numerical analysis. In particular, the freezing time showed no significant difference between the theoretical model and the numerical analysis. The amount of refrigerant for artificial ground freezing was estimated from the numerical analysis and the freezing efficiency obtained from the chamber test. In addition, the energy ratio for maintaining frozen status was calculated by the proposed formula. It is believed that the energy ratio for freezing will depend on the depth of rock cover in the subsea tunnels and the water temperature on the sea floor.

• Journal of Animal Science and Technology
• /
• v.59 no.10
• /
• pp.23.1-23.11
• /
• 2017

Background: Although soybean meal (SBM) is excellent source of protein in diets for poultry, it is sometimes inaccessible, costly and fluctuates in supply. The SBM can partially be replaced by full-fat SBM, but the meals prepared from raw full-fat soybean contain antinutritional factors. To avoid the risk of antinutritional factors, heat treatment is always advisable, but either excessive or under heating the soybean could negatively affect the quality. However, the potential for further improvement of SBM by supplementing with microbial enzymes has been suggested by many researchers. The objective of this study was to evaluate the performance and ileal nutrient digestibility of birds fed on diets containing raw soybeans and supplemented with microbial protease. Methods: A $3{\times}2$ factorial, involving 3 levels of raw full-fat soybean (RFFS; 0, 45 or 75 g/kg of diet) and 2 levels of protease (0 or 15,000 PROT/kg) was used. The birds were raised in a climate-controlled room. A nitrogen-free diet was also offered to a reference group from day 19 to 24 to determine protein and amino acid flow at the terminal ileum and calculate the standardized ileal digestibility of nutrients. On days 10, 24 and 35, body weight and feed leftover were recorded to calculate the body weight gain (BWG), feed intake (FI) and feed conversion ratio (FCR). On day 24, samples of ileal digesta were collected at least from two birds per replicate. Results: When RFFS was increased from 0 to 75 g/kg of diet, the content of trypsin inhibitors was increased from 1747 to 10,193 trypsin inhibitors unit (TIU)/g of diets, and feed consumption of birds was also reduced (P < 0.05). Increasing RFFS level reduced the BWG from hatch 0 to 10 d (P < 0.01) and hatch to 24 d (P < 0.05). The BWG of birds from hatch to 35 was not significantly (P = 0.07) affected. Feed intake was also reduced (P < 0.05) during 0 to 35 d. However, protease supplementation improved (P < 0.05) the BWG and FCR during 0 to 24 d. Rising levels of RFFS increased the weight of pancreas (P < 0.001) and small intestine (P < 0.001) at day 24. Except for methionine, apparent and the corresponding standardized ileal digestibility of CP and AA were reduced (P < 0.01) by increasing levels of RFFS in diets. Conclusion: This study showed that some commercial SBM could be replaced by RFFS in broiler diets, without markedly compromising productivity. The AID and SID of CP and lysine were slightly improved by dietary supplementation of microbial protease.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.25-33
• /
• 2018

Renewable energy has been of interests in the area of modern alternative fuels. Biogas is produced in waste landfill sites through anaerobic digestion processes, including hydrolysis, acidogenesis, organic acid fermentation (acetogenesis), and methane fermentation (methanogenesis). High contents of fine dust and moisture limited its utilization for direct combustion, town gas and vehicle fuel. Thus, this study proposed a new design for a cooling device using a centrifugal cyclone for simultaneous removal of fine dust and moisture as a pretreatment in the purification processes. A heat exchanger and an ID fan, which are installed inside and outside of the cyclone, in order to cool the humid gas below the freezing point and form a foggy mist. Such an atmosphere enhanced to capture fine dust as recirculating the cold mist flow. The water removal rate was 80.8% at a relative humidity of 95%, and the particle removal efficiency was 98.3% for $2.5{\mu}m$. Simultaneous removal efficiency was 70.8% and 99.6% for particle and moisture respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.2
• /
• pp.689-696
• /
• 2017

The practical applications of ordinary high-fluidity concrete have been limited due to several drawbacks, such as high hydration heat, high amount of shrinkage, and non-economic strength development. On the other hand, due to its advantages, such as improvement of construction quality, reduction of construction cost and period, the development of high-fluidity concrete is a pressing need. This study examined the properties of high-fluidity concrete, which can be manufactured on the low binders using a viscosity agent to prevent the segregation of materials. The optimal viscosity agent was selected by an evaluation of the mechanical properties of high-fluidity concrete among six viscosity agents. The acrylic type and urethane type viscosity agents showed the best performance within the range where no material separation occurred. The mechanical properties were evaluated to examine the optimal amount of AC and UT viscosity agent added by mixing two viscosity agents according to the adding ratio and blending them together with high performance water reducing agent. When the ratio of the AC : UT viscosity agents was 5:5, it was most suited for high-fluidity concrete with low binders by increasing the workability and effect of the reducing viscosity.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.1
• /
• pp.61-67
• /
• 2015

The cooling of hot exhaust gas is an important issue for the construction of combustor test facility. Water spray is an effective method for exhaust gas cooling due to its large latent heat in process of evaporation. In this study, 1-D analysis has been performed based on continuity, energy conservation, and saturated vapor property to understand water spray cooling of combustion gas. In the exhaust duct of combustor test facility, the injected water decreases combustion gas temperature, and evaporates in the combustion gas. However, some of the injected water is collected in the sump due to condensation. The evaporation of water helps combustion gas cooling, but causes pressure increase inside the exhaust duct due to increase of vapor pressure. These phenomena has been analyzed by 1-D modeling in this study. From 1-D analysis, the adequate mass flow rate of water spray to cool combustion gas and to avoid excessive pressure rise inside the exhaust duct has been decided.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.8 s.350
• /
• pp.13-18
• /
• 2006

[ $SnO_2$ ] and ZnO nanostructures were grown on the surface of thin film by heat treatment of metal Sn, Zn under Ar gas flow and $O_2$ at atmospheric pressure, respectively. The sensitivity of the $SnO_2$ thin film device on which grown nanowires to CO gas(5,000 ppm) was 50 % at the operating temperature of $200^{\circ}C$. In case of using Pt as catalysts, the sensitivity was enhanced and operating temperature was reduced(73 % at $150^{\circ}C$ ). The sensitivity of the ZnO nanorods device using Cu as catalysts to NOx gas was 90 % at the operating temperature of $200^{\circ}C$. It was found that the sensitivity to CO and NOx gases for the device on which grown nanostructures was much higher than those for general thin film device.

• Applied Chemistry for Engineering
• /
• v.8 no.4
• /
• pp.568-574
• /
• 1997

The effect of microencapsulation of maetal hydride (MH) with copper on the electrode performance of a Ni/MH battery has been investigated. The MH electrodes were prepared with a combination of cold press and paste methods. The discharge capacity of the electrode increased with an addition of small amounts if CMC into the electrode, but decreased when heat-treated in an oxygen-free nitrogen flow. The capacity of a Cu-coated $LaNi_5$ electrode was higher than that of LaNi5electrode. The discharge capacity of the electrode prepared with Cu-coated $LaNi_5$ increased with the increase of copper content in the electrode. It is considered that the increase of copper content enhanced the current density on the electrode surface, leading to the increase of the discharge capacity The MH electrode coated by an acidic electroless plating method showed much higher discharge capacity than that using an alkaline electroless plating method. The discharge capacity of the $LaNi_{4.5}Al_{0.5}$ electrode was higher than that of the $LaNi_5$ electrode. Also, the effect of microencapsulation on the deactivation of $LaNi_5$ was studied using an absorption-desorption cycle in CO-containing hydrogen.

• Journal of Aquaculture
• /
• v.11 no.2
• /
• pp.133-140
• /
• 1998

A 20-week growth trial was conducted in flow-through aquarum system to investigate the practical dietary carbohydrate sources for juvenile abalone (Haliotis discus hannai). Four replicate grops of the abalone averaging 0.125g were fed one of eight diets containing 24.2% wheat flour (WF), 20% dextrin (DEX), 20% sucorse (SUC), 10% $^{\alpha}$-potato starch+10% $^{\beta}$-potato starch (ab-S), 15% $^{\alpha}$-potato starch (a-S15), 20% $^{\alpha}$-potato starch (a-S20), 25% $^{\alpha}$-potato starch (a-S25), or mixture (MIX) with practical ingredients such as soybean meal, corn gluten meal, cotton seed meal and heat flour. In addition, these formulated diets were compare with macroalgae such as dried sea mustard Undaria (D-SM) or dried sea tangle Laminaria(D-ST). Survival rate, weight gain, shell growth and soft body weight of abalone were not significantly affected by the different dietary carbohydrate sources (P>0.05), whereas those fed a-S15 diet were slightly low. These values of abalone fed D-ST were lowest (P<0.05), followed by those fed D-SM. Lipid contents of soft body from abalones fed a-S25, D-ST or D-SM were significantly lower than those of abalone fed other diets (P<0.05). These data indicate that abalone can equally utilize any carbohydrate sources used in this study.

• Journal of the Korean Ceramic Society
• /
• v.56 no.2
• /
• pp.178-183
• /
• 2019

A process of fabricating the foamed glass that has closed pores with 8 ~ 580 ㎛ sizes without a blowing agent by sintering 10 ㎛ boron-free glass powder composed of CaO, MgO, SO₃, Al₂O₃-83 wt% SiO₂ at a molding pressure of 0 ~ 120 MPa and a sintering temperature of 750 ~ 1000℃ was investigated. To analyze the glass transition temperature of glass powder, thermogravimetric analysis-differential thermal analysis (TGA-DTA) method were used. The microstructure and pore size of foamed glass were examined using the optical microscopy and field emission scanning electron microscopy (FE-SEM). For the thermal diffusivity and color of the fabricated samples, a heat flow meter and ultraviolet-visible-near-infrared (UV-VIS-NIR)-colormetry were used, respectively. In the TGA-DTA result, the glass transition temperature of glass powder was confirmed to be 626℃. In the microstructure result, closed pores of 7 ~ 20 ㎛ were formed at 750 ~ 900℃, and they were not affected by the molding pressure and sintering temperature. However, at 1,000℃, when there was 0 MPa molding pressure, closed pores of 580 ㎛ were confirmed, and the pore size decreased as the molding pressure increased. Moreover, at a molding pressure of 30 MPa or higher, closed pores of approximately 400 ㎛ were formed. The porosity showed an increasing trend of smaller molding pressure and larger sintering temperature, and it was controllable in the range of 5.69 ~ 68.45%. In the thermal diffusivity result, there was no change according to the molding pressure, and, by increasing the sintering temperature, up to 0.115 W/m·K could be obtained. The Lab color index (CIE-Lab) results all showed a similar translucent white color regardless of molding pressure and sintering temperature. Therefore, based on the foamed glass without boron and blowing agent, it was confirmed that white foamed glass, which has closed pores of 8 ~ 580 ㎛ and a thermal diffusivity characteristic of 0.115 W/m·K, can be fabricated by changing the molding pressure and sintering temperature.

• Korean Chemical Engineering Research
• /
• v.52 no.2
• /
• pp.233-239
• /
• 2014

The slagging which generated from ash deposition on furnace wall and tube in boiler reduces the heat transfer efficiency and damages to safety of boiler. The slag flow behavior in boiler is affected by melting temperature which is related to ash compositions. In this study, the behavior of slag is researched by using ash fusibility test, called TMA (Thermo-Mechanical Analysis). The technique measures the percentage shrinkage as the function of temperature, T25%, T50%, T75%, T90%. These temperatures indicate different stages of melting. Then, the effect of ash chemical compositions measured from XRF (X-ray Fluorescence Spectrometer) to ash fusion temperatures is discussed. Among the chemical compositions, refractory and fluxing influence on ash fusibility is described. High levels of refractory component and limited amount of fluxing components ($Fe_2O_3$, $K_2O$, CaO) increase overall melting temperatures. High $SiO_2/Al_2O_3$ ratio decrease high melting temperatures (T75%, T90%). Meanwhile, the presence of reasonable levels of fluxing components reduces overall melting temperature. A presence of fluxing component such as $K_2O$ and CaO is found to decrease the T25% values significantly. From this research, it is possible to make a reasonable explanation and prediction of ash fusion characteristic from analysis of TMA results and ash chemical compositions.