• Journal of the Korea Concrete Institute
• /
• v.16 no.6 s.84
• /
• pp.805-811
• /
• 2004

In this paper, effects of mixture proportion and material condition on both fundamental properties, drying and autogenous shrinkage of high performance concrete are discussed. According to the results, for the effect of mixture proportion on the fundamental properties, decrease in W/B and unit water content results in reduction of fluidity, while air content has no variation. Compressive strength exhibits an decreasing tendency with an increase in W/B and unit water content do not remarkable affect the compressive strength. For the effect of materials on the fluidity, the fluidity of low heat portland cement(LPC) is smaller than that of ordinary portland cement(OPC). The use of Polycarbonic acid based superplasticizer(PS) has more favorable effect on enhancing fluidity than Naphtalene based superplasticlzer(NS) and Melamine based superplasticizer(MS). Air content of concrete using LPC is larger than that using OPC. The effects of superplasticizer type on the air content is larger in order of MS, PS and NS. The use of LPC exhibited lower strength development at early age than OPC, whereas after 91days, similar level of compressive strength is achieved regardless of cement type. Compressive strength of concrete is not affected by SP type. For the effect of mixture proportion and materials on drying and autogenous shrinkage, an increase in W/B results in reduction of drying shrinkage and an decrease in water content leads to reduce drying shrinkage. Autogenous shrinkage is not observed until 49 days with the concrete mixture with $35\%$ of W/B and $145 kg/m^3$ of water content. This is due to the combination effects of expansion admixture and shrinkage reducing admixture, which causes an offset of autogenous shrinkage. The use of LPC results in a reduction in autogenous shrinkage compared with OPC. SP type has little influence on the autogenous shrinkage. It is found from the results that mixture proportioning of high performance concrete incorporating fly ash, silica fume, expansion admixture and shrinkage reducing admixture is need to focus on the increase in W/B and the reduction in water content and the use of LPC and MS is also required to use to secure the stability against shrinkage properties.

• The Journal of the Korean bone and joint tumor society
• /
• v.10 no.2
• /
• pp.71-78
• /
• 2004

Purpose: The purpose of this study is to investigate the characteristic of recurred giant cell tumor after bony curettage and cementation, and to review a way to prevent the recurrence. Materials and Methods : Thirty seven cases were analyzed, which were pathologically diagnosed giant cell tumor after diagnostic biopsy or surgical excision, followed by curative curettage, burring and cementation. Location, character, and time interval to recurrence were reviewed. Results: Thirteen out of thirty seven analyzed cases(35%) showed recurrence after primary curettage and cementation. The mean interval to recurrence was sixteen months(5 months to 43 months). Most of recurrence happened within the first two years except two cases. Among the recurred cases, eleven showed recurrence in the vicinity of window area. Two cases recurred in the depth of bone marrow, where cementation was made. The advantage of curettage and cementation is the immediate stability of the operation site, early rehabilitation, and early detection of recurrence. Furthermore, cementation is beneficial in that the cement-producing heat can eradicate the residual tumor burden. In this study, 85% of cases with insufficient curettage (for example, in cases where too small surgical window was made, or where there were anatomical difficulty in approaching the target tumor burden) showed recurrence. Conclusion: Bony curettage, burring and cementation is widely used as the primary curative modality for giant cell tumor. A few other modalities such as chemical cautery using phenol and $H_2O_2$; cryotherapy; and anhydroalcohol have also been introduced, but the benefit of these are still questionable. For some cases that relatively small surgical window was made due to anatomically complicated structures (such as ligament insertion or origin site) over the target tumor burden, unsatisfactory curettage and burring was made. This study showed high chance of recurrence after unsatisfactory curettage, and 85% of recurrence developed in the vicinity of the small window area. Most of the recurrence occurred within the first two years. It is concluded that sufficient window opening, extensive curettage and eradicative burring are key factors to prevent recurrence. Also, it should be reminded that careful and close observation should be made for at least the first two years after initial treatment for early detection of recurrence.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.45 no.12
• /
• pp.1717-1724
• /
• 2016

Probiotic effects of Lactobacillus plantarum pF1 NITE-P1462 (Lp-pF1), L. plantarum KCCM 11352P (Lp-PNU), L. plantarum CBT LP3 KCTC 10782BP (Lp-CB), and L. plantarum KCTC 3099 (Lp-3099) isolated from kimchi and Lactococcus lactis KFCC 11510P (L-lactis) isolated from Doenjang were studied. Resistance to gastric and bile acid, adhesion to intestines in colon cells, thermal stability, and antioxidative and in vitro anticancer effects in HT-29 cancer cells were evaluated. L. plantarum strains showed improved tolerance of gastric and bile acids than L-lactis. Lp-pF1 had better adhesion ability in the intestine than Lp-PNU, Lp-3099, and L-lactis. Lp-pF1 also showed better heat resistance at $50^{\circ}C$, $70^{\circ}C$, and $80^{\circ}C$ than Lp-CB, Lp-3099, and L-lactis. In addition, Lp-pF1 exhibited greater antioxidant activity by scavenging DPPH radicals or hydroxyl radicals and anticancer effects in MTT assay than others. Taken together, these results suggest that L. plantarum isolated from kimchi showed higher probiotic activities with antioxidant and anticancer properties than Lac. lactis isolated from Doenjang. Lp-pF1 revealed the best probiotic activities among L. plantarum and could be used as a promising potential probiotics.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.1
• /
• pp.23-30
• /
• 2007

The ultimate objective of this study is to develop oxygen-enriched combustion techniques applicable to the system of practical industrial boiler. To this end the combustion characteristics of lab-scale LNG combustor were investigated as a first step using the method of numerical simulation by analyzing the flame characteristics and pollutant emission behaviour as a function of oxygen enrichment level. Several useful conclusions could be drawn based on this study. First of all, the increase of oxygen enrichment level instead of air caused long and thin flame called laminar flame feature. This was in good agreement with experimental results appeared in open literature and explained by the effect of the decrease of turbulent mixing due to the decrease of absolute amount of oxidizer flow rate by the absence of the nitrogen species. Further, as expected, oxygen enrichment increased the flame temperatures to a significant level together with concentrations of $CO_2$ and $H_2O$ species because of the elimination of the heat sink and dilution effects by the presence of $N_2$ inert gas. However, the increased flame temperature with $O_2$ enriched air showed the high possibility of the generation of thermal $NO_x$ if nitrogen species were present. In order to remedy the problem caused by the oxygen-enriched combustion, the appropriate amount of recirculation $CO_2$ gas was desirable to enhance the turbulent mixing and thereby flame stability and further optimum determination of operational conditions were necessary. For example, the adjustment of burner with swirl angle of $30\sim45^{\circ}$ increased the combustion efficiency of LNG fuel and simultaneously dropped the $NO_x$ formation.

• Microbiology and Biotechnology Letters
• /
• v.37 no.3
• /
• pp.280-286
• /
• 2009

To investigate anti-phytopathogenic fungal activity of Coptis chinensis, the methanol extract and its organic solvent fractions were prepared. Using the extract and the fractions, in-vitro spore-germination inhibition and mycelial-growth inhibition activities were evaluated against Colletotrichum gloeosporioides, Phytohpthora capsici, Pyricularia grisea, Rhizoctonia solani, Botryosphaeri dothidea, Glomerella cingulata, respectively. Treatment of the methanol extract (500 mg/mL) into the spore of phytopathogenic fungi completely inhibited germinations for 5 days, except B. dothidea, and showed strong antifungal activities against P. grisea and B. cinerea, and antioomycetes activity against P. capsici. The minimal growth inhibition concentrations of the methanol extract against P. grisea, B. cinerea and P. capsici were 300, 300, and 500 mg/mL, respectively. For practical application of C. chinensis in red-pepper field, the hot-water extract (1,000 mg/mL) was prepared in commercial facility, after evaluation of heat stability and solvent-extraction yields of antifungal substances. The 3-times leaf-spray of the extract from June to August, 2008 did not show any deleterious effect to red-pepper. In fact, the leaf-spray promoted plant growth including leaf, root and fruit. The average weight and rind of each fruit were increased to 119% and 117% comparison to those of without treatments. Our results suggest that C. chinensis is a useful source for control of red-pepper diseases and plant growth.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.25 no.5
• /
• pp.383-391
• /
• 1992

A comparative study of enzymatic properties between the trypsin from the cat-shark Cephaloscyllium umbratile ( C-T) and the two trypsins from the mackerel Scomber japonicus $(M-T_A\;and\;M-T_B)$ was carried out following after the previous paper(Pyeun et al., 1991). Trypsin from cat-shark(C-T) showed the higher heat stability compared to the others $(M-T_A\;and\;M-T_B)$ and its denaturation constant$(K_D)$ was $10.68\times10^{-4}\;sec^{-1}\;at\;55^{\circ}C$ with BA-p-NA substrate. The activation energies(Ea) of the trypsins measured at a temperature range from $30^{\circ}C\;to\;50^{\circ}C$ were estimated to be 4.07 kcal/mole for C-T, 11.61 kcal/mole for $M-T_A$, and 8.43kcal/mole for $M-T_B$, respectively. The Km values were $24.9\times10^{-5}\;M\;for\;C-T,\;5.37\times10^{-5}\;M\;for\;M-T_A,\;and\;9.65\times10^{-5}\;M\;for\;M-T_B$. On the other hand, the Ki values for TLCK and DFP determined by Dixon plot were $1.50\times10^{-6}\;M\;and\;9.28\times10^{-6}\;M\;for\;C-T\;2.86\times10^{-6}\;M\;and\;2.11\times10^{-4}\;M\;for\;M-T_A\;and\;3.90\times10^{-6}\;M\;and\;1.60\times10^{-4}\;M\;for\;M-T_B$ Similar amino acid profiles were showed between three trypsins each other, with few exceptions of $M-T_B$ containing higher amount of arginine, and the smaller amount of tryptophan in C-T than the others.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.19 no.5
• /
• pp.469-476
• /
• 1986

Proteolytic activity of the tissue extracts from the muscle of mackerel, Scomber japonicus, and sardine, Sardinops melanostcta, was comparence with referenced to the optimum reaction condition. Thermal stability and change of proteolytic activity of the tissue extracts during storage were investigated. The existence of acid, weak acid and alkaline proteinase was identified in the ordinary and dark muscle of the mackerel and sardine. Specific activity of acid proteinase was stronger than weak acid or alkaline proteinase in the both fish. The proteolytic activity of the tissue extracts on the optimum reaction condition was: ordinary muscle of mackerel, 0.12 nM-Tyr. eq./mg-prot. /min. at pH 3.0 and $50^{\circ}C$; dark muscle of mackerel, 0.36 nM-Tyr. eq./mg-prot. /min. at pH 3.0 and $45^{\circ}C$; ordinary muscle of sardine, 0.45 nM-Tyr. eq./mg-prot. /min. at pH 2.4 and $45^{\circ}C$; dark muscle of sardine, 0.24 nM-Tyr. eq./mg-port. /min. at pH 2.4 and $45^{\circ}C$. The proteinases distributed in the muscle of mackerel and sardine were stable with the heat treatment at $45^{\circ}C$ for 5 minutes, but those in the dark muscle of mackerel was stable with the treatment at $5^{\circ}C$ for 5 minutes. The proteinases from the muscle were slowly inactivated with the whole storage days at $5^{\circ}C\;and\;-15^{\circ}C$, those were more stable at $-15^{\circ}C\;than\;5^{\circ}C$ storage.

• The Journal of the Petrological Society of Korea
• /
• v.21 no.3
• /
• pp.335-365
• /
• 2012

Fission-track (FT) thermochronological records from SE Korean Cretaceous-Paleogene granitic plutons in different fault-bounded blocks reveal contrasting cooling and later thermal histories. Overall cooling patterns are represented by a monotonous (J-shaped) curve in most plutons except some Cretaceous granites retaining a complicated (N-shaped) path due to post-reset re-cooling. Discriminative cooling rates over different temperature ranges can be explained for individual plutons with respect to relative pluton sizes, differences in initial heat loss depending on country rocks, and the presence and proximity of later igneous activity. Even within a single batholith, cooling times for different isotherms were roughly contemporaneous with respect to positions. Insignificant deviations in cooling ages from two different plutons in succession across the Yangsan fault may suggest their contemporaneity before major horizontal fault movement. The extent of later thermal rise recorded locally along the Yangsan and Dongnae fault zones were reached the Apatite Partial Stability Zone ($70-125^{\circ}C$), but did not exceed $200^{\circ}C$. Thermal alteration from fractured zones in the Yangsan-Ulsan fault junction may suggest a thermal reset above $290^{\circ}C$ resulting a complete reset in FT sphene age (31 Ma), caused by a tectonic subsidence in Early Oligocene. A consistency in FT zircon/apatite ages (24 Ma) may imply a sudden rapid cooling over $200-105^{\circ}C$, plausibly related to the abrupt tectonic uplift of the Pohang-Gampo Block including the fault junction in Late Oligocene. A remarkable trend of lower cooling ages for $300-200-100^{\circ}C$ isotherms (i.e., 19% for FT sphene and K-Ar biotite; 20% for FT zircon; 27% for FT apatite) from the east of the Ulsan fault (Pohang-Gampo Block) comparing to the west of the fault may be attributed to retarded cooling times from the Paleogene granites and also reflected by their partially-reduced apatite ages due to later thermal effects.

• Journal of the East Asian Society of Dietary Life
• /
• v.20 no.1
• /
• pp.20-29
• /
• 2010

Naringin has antioxidant and antihyperlipidemic properties, however, phenolic compounds including naringin are unstable in the presence of light, heat and oxygen. Beta-cyclodextrin ($\beta$-CD) is a cyclic heptamer composed of seven glucose units that enhances the stability and solubility of molecules through the formation of inclusion complexes. This study was conducted out to compare the effects of CD-naringin (CD-N) inclusion complexes with naringin on lipid metabolism in high fat-fed animals. Male C57BL/6 mice were fed either CD-N (0.048%, w/w) or naringin (N, 0.02%, w/w) in a 20% high-fat (HFC, 15% lard, 5% corn oil, w/w) diet for 10 weeks. Orlistat (Xenical, 0.01%, w/w) was used as a positive control (PC). There were no differences in body weight, food intake, liver and heart weights, plasma triglyceride(TG), leptin, adiponectin, resistin, IL-$1{\beta}$ and IL-6 concentrations, and hepatic $\beta$-oxidation, carnitine palmitoyl transferase(CPT), glucose-6-phosphate dehydrogenase (G6PD) and malic enzyme activities between the HFC and CD-N groups or between the HFC and N groups. However, both CD-naringin and naringin supplementation les to a significant reduction in the epididymal and perirenal white adipose tissue weights, plasma free fatty acid, insulin and blood glucose concentrations, hepatic cholesterol and TG contents and hepatic fatty acid synthase (FAS), phosphatidate phosphohydrolase (PAP) and HMG-CoA reductase activities compared to the HFC group. The plasma HDL-cholesterol concentration was significantly higher in CD-N and N groups than in HF and PC groups. These results indicate that both CD-naringin and naringin supplementation effectively improved plasma and hepatic lipid metabolism without differences between CD-N and naringin groups.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.6
• /
• pp.71-84
• /
• 2003

The metallic shell of soil-steel structures are so weak in bending moment that it should sustain the applied load by the interaction of the backfill soil around the structures. The shell can be subjected to excessive bending moment during side backfilling or under live-load when the soil cover is less than the minimum value. The current design code specifies the allowable deformation and Duncan(1979) and McGrath et al.(2001) suggested the strength analysis methods to limit the moments by the plastic capacity of the shell. However, the allowable deformation is an empirically determined value and the strength analysis methods are based on the results of FE analysis, hence the experimental verification is necessary. In this study, the full-scale tests were conducted on the high-profile arch to investigate its behaviors during backfilling and under static live-loads. Based on the measurements, the allowable deformation of the tested structure could be estimated to be 1.45% of rise, which is smaller than the specified allowable deformation. The comparison between the measurements and the results of two strength analyses indicate that Duncan underestimates the earth-load moment and overestimates the live-load moment, while McGrath et al. predicts both values close to the actual values. However, as the predicted factors of safeties using two methods coincide with the actual factor of safety, it can be concluded that both methods can predict the structural stability under live-loads adequately when the cover is less than the minimum.