• 한국전기전자재료학회논문지
• /
• 제29권2호
• /
• pp.79-83
• /
• 2016

This research was analyzed thermal characteristics that was appointed disadvantage when smart LED driver ICs was packaged and we applied extracted thermal characteristics for optimal layout design. We confirmed reliability of smart LED driver ICs package without additional heat sink. If the package is not heat sink, we are possible to minimize package. For extracting thermal loss due to overshoot current, we increased driver current by two and three times. As a result of experiment, we obtained 22 mW and 49.5 mW thermal loss. And we obtained optimal data of 350 mA driver current. It is important to distance between power MOSFET and driver ICs. If thhe distance was increased, the temperature of package was decreased. And so we obtained optimal data of 3.7 mm distance between power MOSFET and driver ICs. Finally, we fabricated real package and we analyzed the electrical characteristics. We obtained constant 35 V output voltage and 80% efficiency.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.190-195
• /
• 2008

The objective of this research is to determine overall heat transfer coefficients (K-value) of exterior wall, floor, and roof of Nakseonjae, a Korean traditional residence via field measurement of transient heat flow and temperature difference across each envelope component. Heat flow sensors and T-type thermocouple were attached on the internal and the external surface of each building component, and real-time measurement data were collected for the three consecutive summer days. The K-values determined in this research showed good agreement with other results from open literature. Peak and annual thermal loads of the traditional residence estimated by a commercial energy simulation program were compared with those for a current apartment house. The traditional house showed lower annual cooling load than that of the current building. It may caused by the fact that the traditional building has less air-tight envelopes and no fenestration passing direct solar radiation into the space.

• 대한치과교정학회지
• /
• 제22권3호
• /
• pp.647-656
• /
• 1992

The purpose of this study was to evaluate the elastic memory process in cold worked stainless steel wire and the effect of heat treatment on it. 0.018 inch round and $0.019\times0.025$ inch rectangular wire (ORMCO stainless wire) were used in this study. Each wire type had 4 groups: non-heat treatment group, furnace heat treatment group, electric current heat treatment group, and bending after heat treatment group. Each group was consisted of 10 specimens. With the Jig, each wire was bent into v-shape uniformly, and width of two free ends of each v-shaped wire was measured by caliper (to the point of 0.1 mm correctly) at time interval of offjig, after heat treatment, 1, 2, 3, 4 hours, 1, 2, 3, 4, 5, 6 days, 1, 2, 3, 4 weeks after. The results were as follows: 1. In non-heat treatment group and bending after heat treatment group, elastic memory process was occured $60\%$ within 1 hour, and more than $90\%$ within 1 week. 2. In furnace and electric current heat treatment group, almost all elastic memory process was occured during teat treatment, and then specimen was stabilized dimensionally. 3. Magnitude of deformation by elastic memory was greater in heat treatment group than non heat treatment group and bending after heat treatment group. 4. There was no remarkable difference in deformation pattern between 0.018 inch round wire and $0.019\times0.025$ inch rectangular wire.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.364-369
• /
• 2019

본 논문에서는 전기재해를 일으킬 수 있는 요소를 미리 제거하기 위해 전등부하, 전열부하, 동력부하를 대상으로 누설전류와 절연저항을 측정하여 분포비율과 누적비율을 비교하고 분석하여 보다 효과적이고 신뢰성 있는 누설전류 검출방법을 찾고자 하였다. 누설전류와 절연저항의 적합 비율 차이는 전열부하 32.5%, 전등부하 22.8%, 동력부하 2.2%의 순으로 나타났으며, 누설전류계가 낮은 적합 비율을 나타내었으며, 누설전류계는 측정방법에 따른 오차와 용량성 누설전류 및 영상전류가 포함되어 있기 때문으로 생각되었다.

• 한국재료학회지
• /
• 제24권9호
• /
• pp.465-468
• /
• 2014

The crystallization effects of boron (B) powder on the phase, full width at half maximum (FWHM) values, and critical properties were investigated for in-situ reacted $MgB_2$ bulk superconductors. The semi-crystalline B powder was heat-treated at different temperatures of 1000, 1300 and $1500^{\circ}C$ for 5 hours in an Ar atmosphere. Then, using as-received and heat-treated B powders, the $MgB_2$ samples were prepared at $600^{\circ}C$ for 40 hours in an Ar atmosphere. As the heat-treatment temperature of the B powder increased, both the particle size of the B powder and crystalline phase increased. In the case of $MgB_2$ samples using B powders heat-treated at above $1300^{\circ}C$, unreacted magnesium (Mg) and B remained due to the improved crystallinity of the B powder. As the heat-treatment temperature of B powder increased, the critical current density of $MgB_2$ decreased continuously due to the reduction of grain boundary density and superconducting volume caused by unreacted Mg and B.

• Journal of Welding and Joining
• /
• 제32권2호
• /
• pp.70-75
• /
• 2014

In automotive industry, applying of Mg alloy to autobody has been issued recently as a light metal. But poor resistance spot weldability of Mg alloy is blocking commercialization. So studies on improving resistance spot weldability of Mg alloy is increasing continuously. For reduce loss of heat input during welding, inverter DC power source is considered because of short rise time to target welding current. But rapid rising of welding current can increase temperature rapidly in nugget and oxide film between electrode and base metal, and that causes generating expulsion on low welding current range. In this study, for increase optimum welding current range and prevent generating expulsion, applicate various types of welding current waveform controls during resistance spot welding. For analysis effects of each current waveform control, acceptable welding current regions according to electrode force and welding time is determined and lobe diagram is derived. In result, pre heat is proposed as optimum type of welding current waveform control.

• 한국전기전자재료학회논문지
• /
• 제27권9호
• /
• pp.576-581
• /
• 2014

This study used the heat conductive silicone rubber sample of 0.95 mm thickness to research the properties of current by changing voltage. When the 1, 10, 30, 60, and 90 minute have passed, the running current has been measured through the applied voltage range of 200 V~800 V on setting temperature of $110^{\circ}C{\sim}170^{\circ}C$. As the temperature increased in applied voltage of 800 V, so did the current value according to time in proportion to the increasing temperature. In an analysis of FT-IR (fourier transform infrared) spectrum, the hydroxyl radicals group(O-H) was created by effects of the hydrogen that methyl group is eliminated by addition of the cross-linking agent peroxide.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.337-342
• /
• 2000

We fabricated resistive superconducting fault current limiters based on YB $a_{2}$/C $u_{3}$/ $O_{7}$ thin films and investigated their quench propagation characteristics. The YB $a_{2}$/C $u_{3}$/ $O_{7}$ films was coated with a gold layer and patterned into 1 mm wide meander lines by photolithography. The quench was concluded to start locally and propagates until completed. The quench propagation characteristics were explained based on the heat transfer within the film as well as between the film and the surrounding liquid nitrogen. The quench completion time depended strongly on potential fault current amplitude and not significantly on fault angle which indicates that the quench propagation speed is affected more by heat dissipation rate than by fault current increase rate. The quench completion time was 1 msec at the fault current of 65 $A_{peak/{\ak}}$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.211-213
• /
• 1994

In tins paper, the method of analysis of induction heating is proposed. It's a coupled problem. First, eddy current problem with current source is analyzed using 2-D finite element method, from which eddy current distribution is obtained. And the second, heat source can be calculated directly by the eddy current. Also the temperature distribution is obtained using 2-D finite element method. Eddy current problem and heat transfer problem are dealt with under steady state in this paper.

• 열처리공학회지
• /
• 제16권6호
• /
• pp.341-348
• /
• 2003

Superalloys which can be devided into three categohes, i.e. Ni-base, Co-base, and Fe-base alloys are widely used for high temperature applications. Since superalloys contain many alloying elements and precipitates, its chemistry and processing parameters need to be carefully designed. In this review, current state-of-the art in the superalloy technologies is described with special attention to the heat-treatment for the control of the microstructures and mechanical properties.