• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.8
• /
• pp.1262-1267
• /
• 2004

An anticoagulant was purified from corn silk which has been used in Oriental Medicine. The anticoagulant from corn silk has a molecular mass of 135 kDa, and purified by 24 folds with a recovery of 11%. It was not sensitive to heat and protease treatment. However, periodate oxidation of the anticoagulant resulted in loss of activity significantly, implying that a carbohydrate was responsible for an anticoagulant activity. Galactose, glucose, mannose, fucose, glucosamine, and galactosamine were detected after acid hydrolysis by thin layer chromatography (TLC) and Bio-LC. It was confirmed that anticoagulant had OH and NH bonds by IR, supporting that the anticoagulant is composed of neutrosugar and aminosugar. Its anticoagulating activity was measured by delay in thrombin time (TT) and prothrombin time (PT) without affecting clotting by snake venom and delay in activated partial thromboplastin time (APTT). TT was more sensitive than PT, and was delayed two and three times at the concentration of 60 and 88 nM, respectively. The anticoagulating activity was reduced in the thrombin-induced clotting assay using purified fibrinogen according to the increase of fibrinogen concentration with the apparent Ki value of 23 nM.

• Resources Recycling
• /
• v.15 no.1 s.69
• /
• pp.46-57
• /
• 2006

For the development of combustion technology of RDF(refuse derived fuel), combustion characteristics are examined in bubbling fluidized bed, circulating fluidized bed, continuos combustor and batch type combustor. The characteristics of combustion and exhaust gas has been compared and analyzed in many type of combustion facilities, which has been utilized as basic data for the advanced research of specified RDF combustion facility. Stable combustion has been observed in bubbling and circulating fluidized bed from controled operating condition like the proper feeding rate and superficial gas velocity. In circulating fluidized bed, concentration of NOx has been increased with the operating condition by the fuel-NO and oxygen reaction and $SO_2$ can be considered not to be produced in RDF fluidized bed from very low concentration in flue gas. HCl concentration is 36.4 ppm as average value and lower than standard emission value, but the counter plan is needed. Shaped RDF and fluff RDF have been compared in continuos combustor and batch type combustor and shaped RDF shows benefit for the stable heat recovery and gas emission shows similar value and characteristics.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.172-172
• /
• 2011

Anaerobic digestion(AD) has successfully been used for many applications that have conclusively demonstrated its ability to recycle biogenic wastes. AD has been successfully applied in industrial waste water treatment, stabilsation of sewage sludge, landfill management and recycling of biowaste and agricultural wastes as manure, energy crops. During AD, i.e. organic materials are decomposed by anaerobic forming bacteria and fina1ly converted to excellent fertilizer and biogas which is primarily composed of methane(CH4) and carbon dioxide(CO2) with smaller amounts of hydrogen sulfide(H2S) and ammonia(NH3), trace gases such as hydrogen(H2), nitrogen(N2), carbon monoxide(CO), oxygen(O2) and contain dust particles and siloxanes. The production and utilisation of biogas has several environmental advantages such as i)a renewable energy source, ii)reduction the release of methane to the atomsphere, iii)use as a substitute for fossil fuels. In utilisation of biogas, most of biogas produced from small scale plant e.g. farm-scale AD plant are used to provide as energy source for cooking and lighting, in most of the industrialised countries for energy recovery, environmental and safety reasons are used in combined heat and power(CHP) engines or as a supplement to natural. In particular, biogas to use as vehicle fuel or for grid injection there different biogas treatment steps are necessary, it is important to have a high energy content in biogas with biogas purification and upgrading. The energy content of biogas is in direct proportion to the methane content and by removing trace gases and carbon dioxide in the purification and upgrading process the energy content of biogas in increased. The process of purification and upgrading biogas generates new possibilities for its use since it can then replace natural gas, which is used extensively in many countries, However, those technologies add to the costs of biogas production. It is important to have an optimized purification and upgrading process in terms of low energy consumption and high efficiency giving high methane content in the upgraded gas. A number of technologies for purification and upgrading of biogas have been developed to use as a vehicle fuel or grid injection during the passed twenty years, and several technologies exist today and they are continually being improved. The biomethane which is produced from the purification and the upgrading process of biogas has gained increased attention due to rising oil and natural gas prices and increasing targets for renewable fuel quotes in many countries. New plants are continually being built and the number of biomethane plants was around 100 in 2009.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.44-54
• /
• 2018

Stress and fatigue of the distributor, an equipment of the high-pressure evaporator for the HRSG, were evaluated according to ASME Boiler & Pressure Vessel Code Section VIII Division 2. First, from the results of the piping system analysis model, reaction forces of the tubes connected to the distributor were derived and used as the nozzle load applied to the detailed analysis model of the distributor afterward. Next, the detailed model to analyze the distributor was constructed, the distributor being statically analyzed for the design condition with the steam pressure and the nozzle load. As a result, the maximum stress occurred at the bore of the horizontal nozzle, and the primary membrane stress at the shell and nozzle was found to be less than the allowable. Next, for the transient operating conditions given for the distributor, thermal analysis was performed and the structural analysis was carried out with the steam pressure, nozzle load, and thermal load. Under the transient conditions, the maximum stress occurred at the vertical downcomer nozzle, and of which fatigue life was evaluated. As a result, the cumulative usage factor was less than the allowable and hence the distributor was found to be safe from fatigue failure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.10
• /
• pp.2786-2793
• /
• 2009

Recently, the development and spread of the new recyclable energy becomes urgent because of the depletion of fossil fuel and strengthening the environmental regulation. To recovery from the waste out of the many new recyclable energies has been proved as the most favorable when the potential value of energy source is compared. The RDF from the waste has been approved as the most economical method out of the other methods. However, the toxic gases (HCl, Dioxin etc) and heavy metals generated during the burning of the industrial wastes have been pointed out as problems. The PVC, alkali metal chloride, and alkaline earth metal chloride are major materials for emitting the chlorine and chlorine compounds have the problem such as the erosion on the heat collection device. This research has analyzed the heavy metal components containing in the industrial waste, and the concentration of Cl and S in the industrial waste generated in B industrial complex are slightly high than that of the A industrial complex. The results can be used to discuss the origin of inorganic components in industrial waste and utilized as a base data to improve the performance of the RDF as fuel.

• Resources Recycling
• /
• v.22 no.2
• /
• pp.11-17
• /
• 2013

The recycling technology of carbon residue produced from the process of oil recovery in waste tire pyrolysis is significant in environmental and economical aspects. This study was done to figure out the recycling possibility of carbon residue to activated carbon. For this, the characteristics of the carbon residue obtained from the commercial pyrolysis process of waste tire were studied. Also, the variation of pore structure of carbon residue was studied after 1 hour of carbonization at $600^{\circ}C$ and $800^{\circ}C$ and 3 hours of activation at $950^{\circ}C$. The specific surface area of the carbon residue was $8.0m^2/g$ and it increased to $548.3m^2/g$ after carbonization and activation.

• Journal of Ginseng Research
• /
• v.3 no.2
• /
• pp.168-186
• /
• 1979

Three hundred gram of Korean ginseng root was extracted with 95% ethanol on a boiling water bath for about 300 hr. Evaporation of alcohol yieled 50.2g of dark brown residue which was used by dissolving 4 mg of the residue in 1 ml of physiological saline. The ginseng group and the saline group received each day 0.5 ml per 100 g body weight of ginseng extract and physiological saline, respectively. Both the ginseng and saline group with stress were exposed to positive radial acceleration (1∼29g), cold (5$^{\circ}C$, 0$^{\circ}C$ &-10$^{\circ}C$) and heat (35$^{\circ}C$) environment, and surgical stress. After termination of the last stress, the tolerance, body weight, visceral organ weight, basal metabolism rate, rectal temperature, the number of erythrocyte and leucocyte, hemoglobin level, hematocrit ratio, total serum protein content and it's fraction and the content of adrenal ascorbic acid in the experimental animal exposed to stress were measured and at the corresponding periods, the same measurements were also carried out with the ginseng and the saline groups without stress exposure (serving as control). Results obtained were as follows. 1. Administration of ginseng does depressed the decrease of the tolerance, body weight, visceral organ weight, basal metabolism rate, the number of erythrocyte, hemoglobin value, hematocrit ratio and the A/G ratio in the mice and rats exposed to various stress. 2. The change of the rectal temperature, eosinophile counts, total serum protein content and the content of adrenal ascorbic acid of ginseng group that exposured to various stress facilitates the reaction to, and accelerates the recovery from the stress. 3. Even after hypophysectomy which served the link between the central and the peripheral portion of the stress mechanism, the adrenal ascorbic acid content of ginseng group decreased significantly more than that of the saline group 30 min. after administration of ACTH, while the value approached the normal level significantly closer in the ginseng group than in the saline group 1 and 2 hr after ACTH administration. Judging from the above results, it is concluded that administration of ginseng extract tolerated the experimental animals under the environment of stressfu1 stmuli, although the ginseng has no significant influence upon the stress mechanism in the absence of stressful stimuli. The site of action of the ginseng appears to be in the peripheral portion of the stress mechanism.

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.1
• /
• pp.104-111
• /
• 2011

In order to assess the performance of co-digester using pig slurry and food waste at the farm scale biogas production facility, the anaerobic facility that adopts the one-stage CSTR of 5 $m^3\;day^{-1}$ input scale was designed and installed under the conditions of the OLR of 2.33 kg $m^3\;day^{-1}$ and HRT of 30 days in an pig farmhouse. Several operation parameters were monitored for assessment of the process performance. The anaerobic facility was operated in three stages to compare the performance of the anaerobic co-digester. In the Stage I, that was fed with a mix of pig slurry to food waste ratio of 7:3 in the input volume, where input TS content was 4.7 (${\pm}0.8$) %, and OLR was 0.837-1.668 kg-VS $m^3\;day^{-1}$. An average biogas yield observed was 252 $Nm^3\;day^{-1}$ with methane content 67.9%. This facility was capable of producing an electricity of 626 kWh $day^{-1}$ and a heat recovery of 689 Mcal day-1. In Stage II, that was fed with a mixture of pig slurry and food waste at the ratio of 6:4 in the input volume, where input TS content was 6.9 (${\pm}1.9$) %, and OLR was 1.220-3.524 kg-VS $m^3\;day^{-1}$. The TS content of digestate was increased to 3.0 (${\pm}0.3$) %. In Stage III, that was fed with only pig slurry, input TS content was 3.6 (${\pm}2.0$) %, and OLR was 0.182-2.187 kg-VS $m^3\;day^{-1}$. In stage III, TS and volatile solid contents in the input pig slurry were highly variable, and input VFAs and alkalinity values that affect the performance of anaerobic digester were also more variable and sensitive to the variation of input organic loading during the digester operation. The biogas produced in the stage III, ranged from 11.3 to 170.0 $m^3\;day^{-1}$, which was lower than 222.5-330.2 $m^3\;day^{-1}$ produced in the stage II.

• Nuclear Engineering and Technology
• /
• v.28 no.2
• /
• pp.137-149
• /
• 1996

The present study is to analyze an integral test, BETHSY test 6.9c, which represent loss of RURS accident under mid-loop operation. Both the pressurizer manway and the steam generator outlet plenum manway are opened as vent paths in order to prevent the system from pressurization by removing the steam generated in the core. The main purposes are to gain insights into the physical phenomena and identify sensitive parameters. Assessment of capability of CATHARE2 prediction can be established the effective recovery procedures using the code in an actual plant. Most of important physical phenomena in the experiment could be predicted by the CATHARE2 code. The peak pressure in the upper plenum is predicted higher than experimental value by 7 kPa since the differential pressure between the pressurizer and the surge line is overestimated. The timing of core uncovery is delayed by 500 seconds mainly due to discrepancy in the core void distribution. It is demonstrated that openings of the pressurizer manwey and the steam generator manway can prevent the core uncovery using only gravity feed injection. Although some disagreements are found in the detailed phenomena, the code prediction is considered reasonable for the overall system behaviors.

• Journal of the Microelectronics and Packaging Society
• /
• v.10 no.2
• /
• pp.49-54
• /
• 2003

We have investigated the effects of hydrogen annealing on the physical and electrical properties of $SrBi_{2}Ta_{2}O_9(SBT)$ thin films in the Pt/SBT/Si (MFS) structure and Pt/SBT/Pt (MFM) one, respectively. The microstructure and electrical characteristics of the SBT films were deteriorated after hydrogen annealing due to the damage of the SBT films during the annealing process. To investigate the reason of the degradation of the SBT films in this work, in particular, the effect of the Pt top electrodes, SBT thin films deposited on Si, Pt, respectively, were annealed with the same process conditions. From the XRD, XPS, P-V, and C-V data, it was seen that the SBT itself was degraded after $H_2$ annealing even without the Pt top electrodes. In addition, the degradation of the SBT films after $H_2$ annealing was accelerated by the catalytic reaction of the Pt top electrodes which is so-called hydrogen degradation. To prevent this phenomenon, we proposed the alternative top electrode material, i.e. Ir, and the electrical properties of the SBT thin films were examined in the $Ir/IrO_2/SBT/IrO_2$ structures before and after the H$_2$ annealing and recovery heat-treatment processes. From the results of the P-V measurement, it could be concluded that Ir is one of the promising candidate as the electrode material for degradation resistance in the MFM structure using SBT thin films.