• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.320.1-320
• /
• 2002

In a hard disk drive (HDD) control system, a state-space controller/observer design is popularly adopted fur its advantages such as effective filtering of position and velocity, use of estimation error to handle servo defects, etc. In this report, a systematic method is proposed to accommodate the transport delay in the plant dynamics into the state estimator. (omitted)

• Tribology and Lubricants
• /
• 제22권2호
• /
• pp.59-65
• /
• 2006

In hard disk drives as the head to disk spacing continues to decrease to facilitate recording densities, slider disk interactions have become much more severe due to direct contact of head and disk surfaces in both start/stop and flying cases. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation and tribocharge build-up. The tribocharge build-up in the slider disk interface can cause ESD (electrostatic discharge) damage. In turn, ESD can cause severe melting damage to MR or GMR heads. The spindle speed of typical hard disk drives has increased in recent years from 5400 rpm to 15000 rpm and even higher speeds are anticipated in the near future. And the increasing disk velocity leads to increasing disk acceleration and this might affect the tribocharging phenomena of the slider/disk interface. We investigated the tribocurrent/voltage build-up generated in HDD, operating at increasing disk accelerations. In addition, we examined the effects with relative humidity conditions and rest time. We found that the tribocurrent/voltage was generated during pico-slider/disk interaction and its level was about $3\sim16pA$ and $0.1\sim0.3V$, respectively. Tribocurrent/voltage build-up was reduced with increasing disk acceleration. Higher humidity conditions $(75\sim80%)$ produced lower levels tribovoltage/current. Therefore, a higher tribocharge is expected at a lower disk acceleration and lower relative humidity condition. Rest time affected the charge build-up at the slider-disk interface. The degree of tribocharge build-up increased with increasing rest time.

• 한국소음진동공학회논문집
• /
• 제14권4호
• /
• pp.287-294
• /
• 2004

Dynamic Load/unload (L/UL) mechanism is an alternative to the contact start stop (CSS) technology which eliminates striction and wear failure modes associated with CSS. Inertia latch mechanism becomes important for mobile disk drives because of non operating shock performance. Various types of latch designs have been introduced in hard disk drives to limit a rotary actuator from sudden uncontrolled motion. In this paper, a single spring inertia latch is introduced for a small form optical disk drive, which uses a rotary actuator for moving an optical pick-up. A new small inertia latch with sin91e spring is designed to ensure both feasible and small size. The shock performance of the new inertia latch is experimentally verified.

• Journal of Mechanical Science and Technology
• /
• 제15권3호
• /
• pp.281-290
• /
• 2001

Particle contamination has been an ongoing problem affecting the reliability of the magnetic hard disk drives. Especially the recent use of MR head requires much tighter control of particle contamination due to thermal asperity (TA) phenomenon. In this study, the effects of slider air bearing surface design of TA reduction capability were investigated by manufacturing two types of sliders. Numerical methods were used to simulate the motion of particles in the head/media interface. Experiments were conducted to verify the results predicted by the numerical simulation. Drives were built and exposed to particle contamination using a particle injection chamber, which turned out to be a very simple and reliable particle generation method over conventional aerosol technique. Then the number of TA generated in the drives was recorded and compared. Also the contacts between slider and particles were investigated by acoustic emission study. It was found that a new ABS design, which has aerodynamic U-shaped rail and central flow passage, was beneficial in reducing the particle contamination on the slider.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.177-178
• /
• 2005

The load/unload behavior of the hard disk drive slider is studied in terms of the air bearing static characteristics. The numerical continuation methods are applied to calculate suspension force - equilibrium position curve. The critical preloads of the femto size slider are analyzed. The hi-stability conditions are depicted on the skew angle - preload diagram. The perturbation method is used to check the stability of the solution branches.

• 정보보호학회논문지
• /
• 제25권5호
• /
• pp.1059-1065
• /
• 2015

하드디스크에 설정되는 패스워드는 일반적으로 잘 알려지지 않았을 뿐만 아니라, 설정되면 데이터에 접근이 불가능하기 때문에 포렌식 조사를 방해하는 목적으로 사용될 수 있다. 하드디스크의 패스워드를 해제하기 위해서는 PC-3000과 같은 고가의 도구가 필요한데 이는 조직에 비용 부담을 주며, 해당 도구에 익숙지 않은 조사관에게는 조사 시 어려움을 준다. 본 논문에서는 하드디스크 패스워드를 해제하기 위해 필요한 내용을 정리하고 고가의 도구없이 하드디스크에 설정된 패스워드를 해제하는 방법들을 제안한다. 그리고 이 중 특정 제조사에 특화된 방법을 이용하여 패스워드를 획득하고 하드디스크의 잠금을 해제하는 절차를 제시한다.

• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.335-342
• /
• 1999

Corrosion of the disk has been an ongoing concern for the manufacturers of hard disk drives. With the advent of magnetoresistive (MR) head, very low levels of corrosion and contamination become more critical since the raised defects and corrosion products on the disk surface-anything that heats the MR sensor due to the contact-can distort the output signal of the head. This phenomenon is called as thermal asperity. In this paper, the effect of corrosion as a form of Co migration on the occurrence of thermal asperity in MR drives was investigated. The corrosion test at high temperature (60$^{\circ}C$) and high relative humidity (80%) was emphasized in this study and the testing results at ambient condition were compared. The corrosion on the disks was characterized as the amount of Co ion migration using an ion chromatography (IC) and a time-of-flight secondary ion mass spectroscopy (TOF-SIMS). It is proved that corrosion on the disk surface after storage testing is closely correlated to the amount of Co ions migration from the magnetic layer to disk surfaces and higher Co migration causes more thermal asperities in the drive. In order to reduce Co migration, several methods such as burnishing process and structure of the carbon overcoat were investigated. It is found that the hydrogenated carbon overcoat shows the least Co migration among different types of overcoat layer. However, the most effective way to reduce Co migration is the application of Cr layer between the overcoat and the magnetic alloy layer.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.88-95
• /
• 2005

The head to disk spacing must be decreased to increase recording densities in hard disk drives. Recently, to decrease the head to disk spacing, smooth disk having no bumps onto the lading zone has used. In this research, we compared the number of particles generated in HDD with smooth and textured disks. We used a sampling method using a particle sampler and a CPC (condensation particle counter) to detect particles in HDD. First, we sampled and counted panicles generated with disk rotational speed and various rest times when the smooth disk and textured disks were used, then analyzed the sampled particles by SEM (scanning electron microscopy) and AES (auger electron spectroscopy). In results of measuring particles, more particles in case of LZT disk drive generated than that of the smooth disk drive in all test modes. The number of particles generated in the smooth disk was very low. The particle generation increased as the rest time increased (smooth/LZT disks) and more particles in case of LZT disk drive generated than that of the smooth disk drive. In results of analyzing particle components, Al, Ti, Si components were detected and we could not found differences between components in case of smooth/LZT disk drive.

• 정보저장시스템학회논문집
• /
• 제2권2호
• /
• pp.123-129
• /
• 2006

The head to disk spacing must be decreased to increase recording densities in hard disk drives. Recently, to decrease the head to disk spacing, smooth disk having no bumps onto the lading zone has used. In this research, we compared the number of particles generated ill HDD with smooth and textured disks. We used a sampling method using a particle sampler and a CPC (condensation particle counter) to detect particles in HDD. First, we sampled and counted particles generated with disk rotational speed and various rest times when the smooth disk and textured disks were used, then analyzed the sampled particles by SEM (scanning electron microscopy) and AES (auger electron spectroscopy). In results of measuring particles, more particles in case of LZT disk drive generated than that of the smooth disk drive in all test modes. The number of particles generated in the smooth disk was very low. The particle generation increased as the rest time increased (smooth/LZT disks) and more particles in case of LZT disk drive generated than that of the smooth disk drive. In results of analyzing particle components, Al, Ti, Si components were detected and we could not found differences between components in case of smooth/LZT disk drive.

• 한국정밀공학회지
• /
• 제18권3호
• /
• pp.107-114
• /
• 2001

The durability of head/disk interface is an important issue for hard disk drives. Currently, there are several means of assessing the performance and integrity of the head/disk interface. In this work Track Average Amplitude(TAA) signal was used to analyzed the head/disk interface with respect to variations in disk velocity, slider pre-load and preformed scratch on the disk. Particularly, TAA variation due to disk defect in the form of a scratch was investigated.