• Tribology and Lubricants
• /
• v.28 no.6
• /
• pp.283-288
• /
• 2012

In this study, a new sliding contact problem involving an elastomeric seal, a spherical particle and a hard coated steel counterface was modeled to investigate the detailed wear mechanisms related to the sealing surface. The model was also used to design the optimum coating conditions. A three-dimensional finite element contact problem was modeled and analyzed using the nonlinear finite element code, MARC. The deformed steel surface and stress distributions are presented for different coating layers and thicknesses. When the coating thickness is relatively small, the entrapped particle produces surface plastic deformations such as groove and torus. In addition, the sealing surface can be damaged by abrasive wear as well as fatigue wear. For a relatively thick and multi-layered coating, on the other hand, surface plastic deformation does not occur, and the amount of abrasive and fatigue wear is reduced. Therefore, the proposed contact model and results can be used in the design of various sealing systems, further intensive studies are required.

• Proceedings of the KWS Conference
• /
• 1996.10a
• /
• pp.3-15
• /
• 1996

The formation of a thicker hard alloyed layer have been investigated on the surface of aluminum cast alloy (AC2B) by PTA overlaying process with Cr, Cu and Ni motel powders under the condition of overlaying current 125-200A. overlaying speed 150 mm/min and different powder feeding rate 5-20 g/min. In addition the characteristics of hardening and wear resistance of alloyed layer here been examined in relation to the microstructure of alloyed layer. Main results obtained were summarized as follows: 1) There was an optimum overlaying condition to get a good alloyed layer with smooth surface. This good layer became easy to be formed as increasing overlaying current and decreasing powder feeding rate under a constant overlaying speed. 2) Cu powder was the most superior one in metal powders used due to a wide optimum overlaying condition range, uniform hardness distribution of Hv250-350, good oar resistance and freedom from cracking in alloyed layer with fine hyper-eutectic structure. 3) On the contrary, irregular hardness distribution was usually obtained in Cr ar Ni alloyed layers of which hardness was increased as Cr or Ni contents and reached to maximum hardness of about Hv400-850 at about 60wt%cr or 40wt%Ni in alloyed layer. 4) Cracking occurred in Cr or Ni alloyed layers with higher hardness than Hv250-300 at mere than 20-25wt% of Cr or Ni contents in alloyed layer. Porosity was observed in all alloyed layers but decreased by usage of spherical powder with smooth surface.

• Corrosion Science and Technology
• /
• v.9 no.6
• /
• pp.289-293
• /
• 2010

To investigate the corrosion behavior of tools steel surface in various coating film, the surface of hard coated Ti-Zr-N film on the tool steel by using magnetron-sputtering methods was researched using various experimental methods. STD 61 steels were manufactured by using vacuum furnace and solutionized for 1hr at $1050^{\circ}C$. Steel surface was coated with Ti-Zr-N film at $150^{\circ}C$ and 100W for 1h by using DC-sputtering equipment. Surface characteristics of Ti-Zr-N film coated specimens were investigated by OM, XRD, FE-SEM and nano-scratch tester. And corrosion behaviors of the coated specimen were investigated by polarization test and electrochemical impedance spectroscopy(EG&G Co, PARSTAT 2273. USA). It was found that Ti-Zr-N film coated sample had a thick coated layer and showed a good wear resistance and corrosion resistance of surface compared with ZrN and TiN coated sample. The corrosion resistance and mechanical property of Ti-Zr-N film coated STD 61 alloy increased as sputtering time increased.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.405-410
• /
• 2005

In the hard oxidizing fire iron red glaze which colorated red exposed magnesioferrite and whitlockite-type crystals. And whitlockite-type crystals has formed before magnesioferrite forming in the step of sintering. This study tries to identify the coloration mechanism of hard oxidizing fire iron red glaze by the experiment of substitution of whitlockite-like crystals and to confirm such substitution be able to farm magnesioferrite. As the results of experiment, magnesioferrite was appeared during substitution of two kinds of whitlockite-type. It can be considered that the magnesioferrite colors the iron glaze to red with covering the glaze surface.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2007.02a
• /
• pp.88-88
• /
• 2007

• Proceedings of the Korean Magnestics Society Conference
• /
• 1997.11a
• /
• pp.46-47
• /
• 1997

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2002.05a
• /
• pp.41-41
• /
• 2002

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.05a
• /
• pp.13-14
• /
• 2000

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.05a
• /
• pp.61-61
• /
• 2000

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.05a
• /
• pp.62-63
• /
• 2000