• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.30 no.2
• /
• pp.8-14
• /
• 2007

The powder blasting process has become an important machining technique for the cost effective fabrication of micro devices. This process is similar to sand blasting, and effectively removes hard and brittle materials. A large number of investigations on the abrasive jet machining with such output parameters as material removal rate, penetration and surface roughness have been carried out and reported by various authors. To achieve higher surface roughness, to increase material removal rate and to identify the influence of blasting parameters on the output parameters, we use the taguchi method which is one of the design methods of experiments. We can select process parameters to optimize the blasting process of glass. Experimental results indicate that the taguchi method is useful as a robust design methodology for the powder blasting process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.739-742
• /
• 2000

Micro machining technology has been studied to fabricate small size and high accuracy milli-structure products. To perfectly overcome the conventional mechanical machining methods, the chemical mechanical micro machining(C3M) process was developed. The mechanism of C3M process is that chemical solution etches the material and results in the generation of the chemical reacted layer, and the mechanical micro tool subsequently removes the layer. From the fundamental experiments, the C3M process has been founded to have the advantages of lower machining resistance, tool wear, and higher surface quality and form accuracy than conventional methods. This study focuses on the micro grooving of both the metallic material(SKDII, A1) and hard brittle silicon oxide.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1011-1017
• /
• 1999

Electrolytic in-process dressing grinding technique which enables application of metal bond wheels with fine superabrasives in mirror surface grinding operations has developed. It is possible to make efficient precision machining of hard and brittle material such as ceramic and hard metal by the employment of this technique. However, in order to ensure the success of performances such as efficient machining, surface finish, and surface quality, it is important to sustain the insulating layer that has sharply exposed abrasives in wheel surface. Using AE(Acoustic Emission) sensor, this paper will show whether the insulating layer sustains stably or not in real grinding time. And by comparing AErms value and surface roughness their thresholds for stable electrolytic in-process dressing grinding will be determined.

• Proceedings of the KWS Conference
• /
• 1999.10a
• /
• pp.297-298
• /
• 1999

Cemented carbides material (WC-Co hard alloy) were recognized very important and expensive tool or die assembly parts because of compose for the main elements of rare metal (W and Co etc). This research was developed to separate and recover of WC fine powder contained by WC-Co materials. Recycling process was a new method named by the Tin impregnation for decobaltification on cemented carbides. This reaction occurred to product a brittle Co-Sn intermetallic compounds, thereafter it carried out by acid cleaning solution and physical milling or powdering. New process was able to recover about 60％ WC fine powder from 1 to 5 ${\mu}{\textrm}{m}$.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.497-504
• /
• 1998

The manufacturing processes of the head hardened rails and the principles of the heat treatment for carbon steels are introduced in this paper, To get the good wear resistance of the rail, many kinds of microstructure had been developed for the rail head hardening. One of these is the tempered martensitic structure, which is very hard but brittle because of Quenching-Tempering Process. Another is the fine pearlitic structure by Slack Quenching. Now Banitic structure steels are emerging as a potential new material to replace eutectoid pearlitic steels for rail. The main reason of this change is due to the limitaion of pearlitic microstructure with regard to mechanical properties and wear resistances of railway rails.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.2
• /
• pp.63-68
• /
• 2008

Hard and brittle materials, such as Ni- and Ti-based alloys, glass, and ceramics, are very useful in aerospace, marine, electronics, and high-temperature applications because of their extremely versatile mechanical and chemical properties. One Ni-based alloy, Inconel 718, is a precipitation-hardenable material designed with exceptionally high yield strength, ultimate tensile strength, elastic modulus, and corrosion resistance with outstanding weldability and excellent creep-rupture properties at moderately high temperatures. However, conventional machining of this alloy presents a challenge to industry. Ultrasonic vibration cutting (UVC) has recently been used to cut this difficult-to-machine material and obtain a high quality surface finish. This paper describes an experimental study of the UVC parameters for Inconel 718, including the cutting force components, tool wear, chip formation, and surface roughness over a range of cutting conditions. A comparison was also made between conventional turning (CT) and UVC using scanning electron microscopy observations of tool wear. The tool wear measured during UVC at low cutting speeds was lower than CT. UVC resulted in better surface finishes compared to CT under the same cutting conditions. Therefore, UVC performed better than CT at low cutting speeds for all measures compared.

• Advances in materials Research
• /
• v.2 no.4
• /
• pp.221-235
• /
• 2013

To obtain bronze with good mechanical properties and high wear resistance, a new bronze (CADZ) is proposed on the basis of various fundamental information. The CADZ consists of the elements Al10.5, Fe4.2, Sn3.7 and Ni3.1, and its design is based on Cu-Al10.5 alloy. The Cu-10.5%Al is very hard and brittle. To obtain the high material ductility of the Cu-10.5%Al alloy, an attempt was made to add a few percent of Sn. Moreover, to make high strength of the Cu alloy, microstructure with small grains was created by the proper amount of Fe and Ni (Fe/Ni = 0.89). The mechanical properties of the CADZ sample have been examined experimentally, and those were compared with commercial bronzes. The tensile strength and wear resistance of CADZ are higher than those for commercial bronzes. Although the ductility of CADZ is the lower level, the strain to failure of CADZ is about 2.0~5.0% higher than that for the Cu-Al10.5 alloy. Details of the microstructural effects on the mechanical properties in the CADZ sample were further discussed using various experimental results.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.831-836
• /
• 2000

During machining, since more than 50% compliance of the cutting point in machine tool structures comes from headstocks, with the remainder coming from beds, slides and structural joints, the structural analysis of the headstock is very important to improve the static and dynamic performances. Especially, in case of machining hard and brittle materials such as glasses and ceramics with the grinding machine, the reinforced headstock with the high damping material is demanded. Since the fiber reinforced composite materials have excellent properties for structures, owing to its high specific modulus, high damping and low thermal expansion, it is expected that the dynamic and thermal characteristics of the headstock will be improved if they are employed as the materials fur headstock. In this paper, the design and the manufacturing methods as well as the static and dynamic characteristics of a steel-composite hybrid headstock were investigated analytically and experimentally to improve the performance of the grinding machine system.

• Current Optics and Photonics
• /
• v.6 no.3
• /
• pp.236-243
• /
• 2022

Monocrystalline silicon has excellent properties, but it is difficult to design and manufacture silicon-based mirrors that can meet engineering applications because of its hard and brittle properties. This paper used monocrystalline silicon as the main mirror material in an imaging system to carry out a feasibility study. The lightweight design of the mirror is completed by the method of center support and edge cutting. The support structure of the mirror was designed to meet the conditions of wide temperature applications. Isight software was used to optimize the feasibility sample, and the optimized results are that the root mean square error of the mirror surface is 3.6 nm, the rigid body displacement of the mirror is 2.1 ㎛, and the angular displacement is 2.5" under the conditions of a temperature of ∆20 ℃ and a gravity load of 1 g. The optimized result show that the silicon-based mirror developed in this paper can meet the requirements of engineering applications. This research on silicon-based mirrors can provide guidance for the application of other silicon-based mirrors.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.5
• /
• pp.171-176
• /
• 2001

Plasma Display Panel(PDP) is a type of flat panel display utilizing the light emission produced by gas discharge. Barrier Ribs of PDP separating each sub-pixel prevents optical and electrical crosstalks from adjacent sub-pixels. Mold for forming barrier ribs has been newly researched to overcome the disadvantages of conventional manufacturing process such as screen printing, sand-blasting and photosensitive glass methods. Mold for PDP barrier ribs have stripes of micro grooves transferring glass-material wall. In this paper, Stripes of grooves of which width 48${\mu}{\textrm}{m}$ and 270${\mu}{\textrm}{m}$, depth 124${\mu}{\textrm}{m}$, pitch 274${\mu}{\textrm}{m}$ was acquired by machining hard and brittle materials of WC, Silicon, Alumina with dicing saw blade. Maximum roughness of the bottom and sidewall of the grooves was respectively 120nm, 287nm in grooving WC. Maximum tilt angle caused by difference between upper-most width and lower-most width was 2$^{\circ}$. Maximum Radius of bottom curvatures was 7.75${\mu}{\textrm}{m}$. This results satisfies the specification for barrier ribs of 50 inch XGA PDP if the groove form of mold was fully transferred to the barrier ribs. Barrier ribs were formed with Silicone rubber mold, which is transferred from grooved hard materials. Silicone rubber mold has elasticity accommodating the waveness of lower glass plate of PDP.