• 한국진공학회지
• /
• 제15권3호
• /
• pp.325-330
• /
• 2006

ITER (International Thermonuclear Experimental Reactor) 조달용 일차벽의 제조 건전성을 검증하기 위해서, 일차벽을 구성하는 Cu/SS mock-up을 제작하여 고열부하 시험을 수행하였다. Cu/SS mock-up은 CuCrZr과 SS316L이 사용되었으며, 두 금속은 $1050^{\circ}C$, 150 MPa의 조건에서 고온등방가압법 (HIP, Hot Isostatic Pressing) 과정을 통해 접합되었다. 시험에 사용된 고열부하 장치는 일본 원자력연구소의 JEBIS (JAEA Electron Beam Irradiation Stand)를 이용하였으며, 시험 조건은 FEM 코드인 ANSYS 해석을 통해 결정하였다. 시험은 $5MW/m^2$의 고열부하를 15초간 인가하고, 30초간 냉각하는 방법으로 수행되었으며, 시험 종료 후 얻어진 시험결과와 해석결과가 잘 일치함을 확인하였다.

• Nuclear Engineering and Technology
• /
• 제42권6호
• /
• pp.662-669
• /
• 2010

To develop the manufacturing methods for the blanket first wall (FW) of the International Thermonuclear Experimental Reactor (ITER) and to verify the integrity of the joint, Be/Cu mockups were fabricated and tested at the KoHLT-1 (Korea Heat Load Test facility), a graphite heater facility located at the Korea Atomic Energy Research Institute (KAERI). Since Be and Cu joining is the focus of the present study, the fabricated mockups had a CuCrZr heat sink joined with three Be tiles as an armor material, unlike the original ITER blanket FW, which has a stainless steel structure and coolant tubes. Hot isostatic pressing (HIP) was carried out at $580^{\circ}C$ and 100 MPa for 2 hours as the method for Be/Cu joining. Three interlayers, namely, $1{\mu}mCr/10{\mu}mCu$, $1{\mu}mTi/0.5{\mu}mCr/10{\mu}mCu$, and $5{\mu}mTi/10{\mu}mCu$ were applied as a coating to the Be tiles by a physical vapor deposition (PVD) method. A shear test was performed with the specimens, which were fabricated by the same methods as those used to fabricate the mockups. The average values were 125 MPa to 180 MPa, and the samples with the $1{\mu}mCr/10{\mu}mCu$ interlayer showed the lowest value. No defect or delamination was found in the joints of the mockups by the developed ultrasonic test using a flat-type probe with a 10 MHz frequency and a 0.25 inch diameter. High heat flux (HHF) tests were performed at $1.0\;MW/m^2$ heat flux for each mockup using the given conditions, and the results were analyzed by ANSYS-CFX code. For the test criteria, an expected fatigue lifetime about 1,000 cycles was obtained by analysis with ANSYS-mechanical code. Mockups using the interlayers of $1{\mu}mTi/0.5{\mu}mCr/10{\mu}mCu$ and $5{\mu}mTi/10{\mu}mCu$ survived up to 1,100 cycles over the required number of cycles. However, one of the Be tiles in the other two mockups using the $1{\mu}mCr/10{\mu}mCu$ interlayer was detached during the screening test, and others were detached by discharge after 862 cycles. The integrity of the joints using the proposed interlayers was proven by the HHF test, but the other interlayer requires more study before it can be used for the joining of Be to Cu. Moreover, it was confirmed that the measured temperatures agreed well with the analysis temperatures, which were used to estimate the lifetime and that the developed facility showed its capability of the long time operation.

• Geomechanics and Engineering
• /
• 제10권5호
• /
• pp.677-687
• /
• 2016

Industrialization and urbanization are the two phenomena that are going relentless all over the world. The consequence of this economic success has been a massive increase in waste on one hand and increasing demand for suitable sites for construction on the other. Owing to the surplus raw materials and energy requirement needed for manufacturing synthetic fibers, applications of waste fibers for reinforcing soils evidenced to offer economic and environmental benefits. The main objective of the proposed work is to explore the possibilities of improving the strength of soil using fly ash waste as an admixture and Human Hair Fiber (HHF) as reinforcement such that they can be used for construction of embankments and land reclamation projects. The effect of fiber content on soil - fly ash mixture was observed through a series of laboratory tests such as compaction tests, CBR and unconfined compression tests. From the stress - strain curves, it was observed that the UCC strength for the optimised soil - flyash mixture reinforced with 0.75% human hair fibers is nearly 2.85 times higher than that of the untreated soil. Further, it has been noticed that there is about 7.73 times increase in CBR for the reinforced soil compared to untreated soil. This drastic increase in strength may be due to the fact that HHF offer more pull-out resistance which makes the fibers act like a bridge to prevent further cracking and thereby it improves the toughness which in turn prevent the brittle failure of soil-flyash specimen. Hence, the test results reveal that the inclusion of randomly distributed HHF in soil significantly improves the engineering properties of soil and can be effectively utilized in pavements. SEM analysis explained the change of microstructures and the formation of hydration products that offered increase in strength and it was found to be in accordance with strength tests.

• Nuclear Engineering and Technology
• /
• 제55권6호
• /
• pp.2139-2146
• /
• 2023

During reactor operation, the divertor must withstand unprecedented simultaneous high heat fluxes and high-energy neutron irradiation. The extremely severe service environment of the divertor imposes a huge challenge to the bonding quality of divertor joints, i.e., the joints must withstand thermal, mechanical and neutron loads, as well as cyclic mode of operation. In this paper, potassium-doped tungsten (KW) is selected as the plasma facing material (PFM), oxygen-free copper (OFC) as the interlayer, oxide dispersion strengthened copper (ODS-Cu) alloy as the heat sink material, and reduced activation ferritic/martensitic (RAFM) steel as the structural material. In this study, a vacuum brazing technology is proposed and optimized to bond Cu and ODS-Cu alloy with the silver-free brazing material CuSnTi. The most appropriate brazing parameters are a brazing temperature of 940 ℃ and a holding time of 15 min. High-quality bonding interfaces have been successfully obtained by vacuum brazing technology, and the average shear strength of the as-obtained KW/Cu and ODS-Cu alloy joints is ~268 MPa. And a fabrication route for manufacturing the flat-type divertor target based on brazing technology is set. For evaluating the reliability of the fabrication technologies under the reactor relevant condition, the high heat flux test at 20 MW/m² for the as-manufactured flat-type KW/Cu/ODS-Cu/RAFM mockup is carried out by using the Electron-beam Material testing Scenario (EMS-60) with water cooling. This paper reports the improved vacuum brazing technology to connect Cu to ODS-Cu alloy and summarizes the production route, high heat flux (HHF) test, the pre and post non-destructive examination, and the surface results of the flat-type KW/Cu/ODS-Cu/RAFM mockup after the HHF test. The test results demonstrate that the mockup manufactured according to the fabrication route still have structural and interfacial integrity under cyclic high heat loads.

• 전기학회논문지P
• /
• 제67권1호
• /
• pp.1-8
• /
• 2018

ACL and DCL are have been conventionally used for reducing harmonic current on the input side of an ACMD. The current distortion ratio ITHD using ACL and DCL is only 35% to 85%, therefore to satisfy the IEEE Std. 519 requirements, the line filters has been focused as an alternative means. Those are installed between the AC power supply and the input of the ACMD, and must meet the IEEE Std. 519, be economical and be compact. To contribute to the widespread of using these line filters, we discussed concerning its topologies, simulation results, prototype test results as well as the cost evaluations. It included not only the proposed (NHHF) new hybrid harmonic filters which have both merits of simplicity and economic but also the past (BBHF) broadband harmonic filters and (HHF) hybrid harmonic filters.

• 한국약용작물학회지
• /
• 제25권3호
• /
• pp.152-159
• /
• 2017

Background: In this study, examined the effects of an extract of a mixture of Angelica gigas, Cnidium officinale, Paeonia lactiflora, and Rehmannia glutinosa fermented by Leuconostoc mesenteroides, with enhanced value and functionality. In oriental medicine, a mixture of these herbs is called Samultang. Methods and Results: In this study, we evaluated the effects of a fermented extract of Samultang on oxidative stress, procollagen type I expression, and melanin production. Samultang was extracted with 70% ethanol, followed by inoculation with Leuconostoc mesenteroides to obtain the fermented extract. The evaluation of viability of B16F10 cells and human foreskin fibroblast (HHF) revealed that both ethanol and fermented extracts of Samultang were non-toxic. The results of 1,1-diphenyl-2-picrylhydrazyl (DPPH) test showed that the fermented extract of Samultang ($SC_{50}value=100{\mu}g/m{\ell}$) was a more effective DPPH free radical scavenger than its ethanol extract. In addition, procollagen type I expression was higher in cells treated with the fermented extract of Samultang than in cells treated with ethanol. In the non-toxic concentration range, the fermented extract of Samultang showed strong inhibitory effect on melanin production in ${\alpha}-melanocyte$ stimulatin hormone-stimulated B16F10 cells ($IC_{50}=37.9{\mu}g/m{\ell}$). Conclusions: These results suggest that the fermented extract of Samultang has considerable protential as a cosmetic ingredient owing to its antioxidant, anti-wrinkle, and whitening effects.