Liquid hydrogen (LH2) has a higher density than gaseous hydrogen, so it has high transport efficiency and can be stored at relatively low pressure. In order to use efficient bulk hydrogen in the industry, research for the LH2 supply system is needed. In the high-pressure hydrogen station based on LH2 currently being developed in Korea, a heat exchanger is used to heat up supercritical hydrogen at 700 bar and 60 K, which is pressurized by a cryogenic high-pressure pump, to gas hydrogen at 700 bar and 300 K. Accordingly, the heat exchanger used in the hydrogen station should consider the design of high-pressure tubes, miniaturization, and freezing prevention. A helical heat exchanger generates secondary flow due to the curvature characteristics of a curved tube and can be miniaturized compared to a straight one on the same heat transfer length. This paper evaluates the heat transfer performance through parametric study on the distance between coils, guide effect, and anti-icing design of helical heat exchanger. The helical heat exchanger has better heat transfer performance than the straight tube exchanger due to the influence of the secondary flow. When the distance between the coils is uniform, the heat transfer is enhanced. The guide between coils increases the heat transfer performance by increasing the heat transfer length of the shell side fluid. The freezing is observed around the inlet of distribution tube wall, and to solve this problem, an anti-icing structure and a modified operating condition are suggested.
국내의 줄눈 콘크리트 포장설계에 주로 사용되는 다웰바 설계 기준은 국외 기준과 검증되지 않은 경험에 의해 사용되고 있다. 또한 다웰바의 설치는 길어깨나 하부층의 조건 등을 고려하지 못한 상태에서 슬래브 폭에 대하여 일률적으로 적용되고 있다. 이에 다웰바를 합리적으로 설계하기 위해서는 다웰바 거동에 대한 고찰이 요구되며, 이를 3차원 유한요소해석을 이용하여 수행하였다. 다웰바의 거동에 대한 3차원 유한요소해석 결과의 타당성을 검토하기 위하여 Timoshenko이론의 다웰바 거동을 비교하였다. 또한 실제 도로에서 교통하중이 여러 개의 다웰바에 분산 전달하는 다웰바의 그룹작용(Dowel Group Action)을 3차원 유한요소해석을 통하여 다웰바 그룹작용 적용범위를 산정하였다. 본 연구에서 제시된 다웰바 그룹작용 범위는 Friberg의 그룹작용 범위와는 상이한 결과가 나타났으며, 비교적 최근 연구 결과인 Tabatabaie의 그룹작용 범위의 연구결과와 유사한 결과가 도출되었다.
With the increasing interest of reducing process variation, statistical process control has served the pivotal tool in most industrial quality programs. In this study, system analyses have been performed associated with a cost incorporated version of a process control, a quadratic loss-based X over bar control chart model. Specifically, two issues, the capital/research investments for improvement of a system and the precision of a parameter estimation, have been addressed and discussed. Through the analysis of experimental results, we show that process variability is seen to be one of the most important sources of loss and quality improvement efforts should be directed to reduce this variability. We further derive the results that, even if the optimal designs may be sensitive, the model appears to be robust with regard to misspecification of parameters. The approach and discussion taken in this study provide a meaningful guide for proper process control. We conclude this study with providing general comments.
In this paper, in order to achieve slim and light liquid crystal display, we examine the optical conditions that can obtain uniform light with higher optical efficiency over whole light guide plate (LGP) through simulation. Furthermore, to overcome the issues of hot spot in front of red, green, and blue light emitting diodes (RGB LEDs) source and non-uniform color mixing, we propose four shaped color mixing bars tied up with the LGP and check the optical characteristics of the LGP with them by simulation. Consequently, we could know the optical conditions of improving optical efficiency and optical uniformity in the LGP through the optical design. Also we confirmed that the issues of the hot spot and non-uniform color mixing in edge type LED could be solved by using the ${\bigwedge}$-shaped window color mixing bar.
무치악 환자를 수복할 때 임플란트 피개의치를 이용한 치료법은 전통적인 총의치의 문제점인 저작시 동통, 의치의 부족한 유지와 안정을 포함하는 기능저하 문제 등을 해결할 수 있는 방법이다. $Locator^{(R)}$ (Zest Anchors LLC, Espandido, USA) 어태치먼트는 임플란트 피개의치에 사용되는 어태치먼트 중 수직적으로 필요한 공간이 가장 적고, 나일론 부품에 따라 유지력 조절이 용이하다. 하지만 Ball이나 Bar에 비해 기능시 부품의 마모로 유지력이 빠르게 감소하는 특징이 있어 가급적 임플란트 간 각도가 최소가 되도록 식립하려는 노력이 필요하다.
본 연구는 분전반 또는 배전반에 설치되는 부스바(busbar)의 절연 피복을 절단하는 커팅기에 관한 기술로써, 연구 결과, 첫째, 커팅기 상부와 하부에 각각 레이저기가 부착된 하우징을 포함하는 커팅유닛 및 프레임의 상부에 설치되고, 부스바의 피복 커팅거리를 조절하는 스토퍼로 구성된 것이 특징인 부스바 피복 레이저 커팅기이다. 둘째, 프레임은, 테이블의 후방 측 단부에 위치하도록 상부에 길이 방향으로 가이드 바가 놓여 설치되고 상부 중간 부분에서 전방과 후방에 각각 수직 상으로 포스트가 설치되며, 전방 포스트의 외측부에 위치하도록 테이블에 커팅 홀이 형성된 것이 특징이다. 셋째, 서포터는, 프레임에 배치된 가이드 바의 상부에 고정 설치되고, 실린더와 지지 판으로 구성된 것이 특징이다. 본 연구의 의미는 작업자의 안전사고를 방지하며, 커팅 작업의 효율성을 높이고, 부스바의 표면에 흠집이 발생하는 것을 방지하는 효과가 있다는데 연구의 의미를 찾을 수 있었다.
Global interests in RFID are increased and Korean government and companies make an active effort to propagate and spread RFID. Due to the overwhelming advantages of RFID system in comparison with existing bar code system, ripple effects on logistics sector among the utilizing fields of RFID technology are expected to be great, but application of RFID system is lowly progressed unlike the expectation of several experts. Therefore, this research extracts precedent studies on theoretical background, applying fields, promotion condition and domestic/foreign parts of RFID system, factors for operating domestic RFID system and effects and considers the effects of RFID's external variables on easiness and effectiveness of TAM. It confirms the relations of RFID applying effects for companies applying and utilizing RFID and verifies the relations among the effects for application of RFID system, accepting intention of RFID system and applying effects. Based on the results of analysis, it should play a role of good guide for all of companies and institution who will introduce RFID system to all of Korean logistics fields, make policies and systems which promote RFID acceptance nationally and socially and play a role of guide making confident climate for RFID technolog
The binders introduced in Korea were originally designed to be used for Japonica varieties which have realtively long stem and are highly resistant to shattering. In order to use it for Tongil varieties which are short and easy to be shattered, mechanical modifications are necessary to reduce a grain loss incurred during its operation. This study was intended to investigate the binding unit, one of the major factors affecting grain losses. The binding parts of three binders used in Korea were analyzed and the grain loss was experimentally assessed for these binders. The results obtained from this study are summarized as follows: 1. From the motion analysis of discharge mechanism, the trajectory of the discharge arm appeared to be either circular or skewed elliptic. The velocity of a circular path mechanism was constant and smaller than that of a skewed elliptic path mechanism. The discharge grain loss of the former was about twice less than that of the latter. 2. It was found that the grain loss incurred due to the collision of the paddy bundles and ground was considerably high for Tongil varieties. The auxiliary discharge bar gave a significant influence on the motion and posture of the bundles, and the degree of impact on ground. 3. The installation of an auxiliary bar, which guides the paddy bundles smoothly to ground in order to reduce impact when the bundles fall down on ground, appeared to be very effective since the grain losses could be decreased by about 1.6 percentage point. However, the guide bar should be installed after some mechanical modification to reduce the velocity of discharge arm has been made.
심한 하악 치조골 흡수룰 보이는 완전 무치악 환자에서 의치는 환자의 저작 효율이 극히 저하되며 특히 치조골의 형태가 불규칙한 경우 의치의 안정성은 더 떨어질 수 있다. 이때 임플란트를 통한 지지를 얻는 피개의치를 통해 편안감 회복과 향후 지속적인 치조골 흡수를 줄이는데 도움을 줄 수 있다. 임플란트 피개의치를 위한 하방의 attachment는 크게 bar attachment와 solitary attachment로 나뉘며 임플란트 고정체의 위치가 하악 전방 치조골에 있으면서 의치 전체가 견고한 지지를 얻기 위해서는 bar attachment가 유리하고 구치부에도 고정체가 위치하며 쉬운 착탈과 유지관리의 편의를 얻고자 하면 solitary attachment를 고려할 수 있다. 본 증례는 환자의 상황에 따른 임플란트 식립 위치 결정, attachment를 선택을 통하여 임플란트 피개의치를 다양하게 적용하여 만족할만한 결과를 얻어 이를 보고하는 바이다.
As new city apartment construction of five brought about the short of the domestic output rocal construction materials , therefore the construction materials have been in part imported from foreign, here it is important that it is ensured the warranty of the quality for the construction materials lacking K.S. mark. Therefore in this research, we are trying to grasp the degree of strength of the concrete made as the cement from china and the intensity power of the estimate for the quality of construction materials and the guide in making a construction.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.