• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.2
• /
• pp.74-79
• /
• 2010

The synthesis and reactivities of molybdenum carbide crystallites were examined in this study. Especially, the effect of synthesis conditions were scrutinized on the preparation of molybdenum carbide crystallites. In order to perform this purpose, various characterization techniques such as BET surface area and oxygen uptake measurements were employed for the synthesized molybdenum carbide crystallites. First of all, the molybdenum carbide crystallites were synthesized using molybdenum oxide crystallites and methane gas or methane-hydrogen mixture. The experimental results showed that BET surface areas ranged from $7.4m^2/g$ to $31m^2/g$ and oxygen uptake values varied from $8.1{\mu}mol/g$ to $24.3{\mu}mol/g$. The Mo compounds were found to be active for ammonia decomposition reaction. Even though there are some molybdenum carbide crystallites that were exceeded by Pt/$Al_2O_3$ crystallite, the steady state reactivities for other molybdenum carbide crystallites were comparable to or even higher than that determined for the Pt/$Al_2O_3$ crystallite. These results implied that molybdenum carbide crystallites could be one of the promising crystallites that might be substitutes for Pt-like noble metal crystallites in the petroleum processes.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.2
• /
• pp.80-84
• /
• 2010

The temperature-programmed reduction of titanium oxide ($TiO_2$) with pure $CH_4$ was used for the preparation of titanium carbide crystallites. The synthesized materials had the different surface areas, indicating that the structural properties of these materials were strong functions of two different heating rates and space velocity employed. The titanium carbide crystallites were active for $NH_3$ decomposition. Since the reactivity varied with changes in the particle size, ammonia decomposition reactivity over the titanium carbides crystallites appeared to be related to the different active species. The reactivities of titanium carbide crystallites were two and three times lower than those of the vanadium and molybdenum carbide crystallites, respectively. These results suggested that the difference in activities might be related to the degree of electron transfer between metals and carbon.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.3
• /
• pp.125-129
• /
• 2009

The preparation and characterization of niobium carbide crystallites were investigated in this study, and in particular, the effect of preparation conditions were studied on the synthesis of niobium carbides crystallites. For this purpose, various characterization techniques including x-ray diffraction, BET surface area, and oxygen uptake measurements were employed to characterize the synthesized niobium carbide crystallites. The niobium carbide crystallites were prepared using niobium oxide and methane gas or methane-hydrogen mixture. Using x-ray diffraction a lattice parameter of $4.45{\AA}$ and a crystallite size ranging from $52{\AA}$ to $580{\AA}$ was found. BET surface areas ranged from $3.2\;m^2/g$ to $16.6\;m^2/g$ and oxygen uptake values varied from $0.5{\mu}mol/g$ to $6.1{\mu}mol/g$. It was observed that niobium carbide crystallites were active for ammonia decomposition reaction. While the BET surface area increased with increasing the oxygen uptake, the conversion of ammonia decomposition reaction decreased. These results indicated that the ammonia decomposition over these materials was considered to be structure-sensitive.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.670-675
• /
• 2016

Calcium phosphate crystallites were prepared by wet chemical method for use in artificial bone. In order to obtain ${\beta}$-tricalcium phosphate (TCP), nano-crystalline calcium phosphate (CaP) was precipitated at $37^{\circ}C$ and at $pH5.0{\pm}0.1$ under stirring using highly active $Ca(OH)_2$ in DI water and an aqueous solution of $H_3PO_4$. The precipitated nano-crystalline CaP solution was kept at $90^{\circ}C$ for the growth of CaP crystallites. Through the growing process of CaP crystallites, we were able to obtain various sizes of rectangular CaP crystallites according to the crystal growing times. Dry nano-crystalline CaP powders at $37^{\circ}C$ were mixed with dry macro-crystalline CaP crystallites and the shaped mixture sample was fired at $1150^{\circ}C$ to make a ${\beta}-TCP$ block. Several tens of nm powders were uniformly coated on the surface, which was comprised of powders of several tens of ${\mu}m$, using a vibrator. The mixing ratio between the nanometer powders and the micrometer powders greatly affected the mechanical strength of the mixture block; the most appropriate ratio of these two materials was 50 wt% to 50 wt%. The sintered block showed improved mechanical strength, which was caused by the solid state interaction between the nano-crystalline ${\beta}-TCP$ and the macro-crystalline ${\beta}-TCP$.

• Korean Journal of Materials Research
• /
• v.8 no.3
• /
• pp.229-237
• /
• 1998

We grew the hexagonal GaN films on (100) Si and (00.1) sapphire substrates in the temperature range of $300~730^{\circ}C$ by the direct reaction between thermally ionized N-source and thermally evaporated Ga-source. The GaN growth rates are increased at the initial stage of GaN formation and it was saturated to some values by the coalescence of each crystallites. The oxygen signal was observed in XPS spectra for all the GaN films grown in this work, especially low- temperature grown GaN film may due to incorporation of the residual oxygen in the growth chamber. The surface of low-temperature and shorter time grown films covered only Ga-droplets. however, with increasing the both substrate temperature and the growth time GaN is growth to crystallites. and coalescence to ring-type crystallites. With sufficient supply of N-source, they were changed to platelets. In the PL spectrum measured at 20 K, we observed the impurity related emission at 3.32eV and 3.38eV.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.8
• /
• pp.708-712
• /
• 2002

The crystallization of amorphous $\alpha$-Fe$_2$O$_3$/$\alpha$-AI$_2$O$_3$(0001) thin films during thermal annealing in air has been studied using real-time synchrotron x-ray scattering. The well aligned (0.02$^{\circ}$/ FWHM) $\alpha$-Fe$_2$O$_3$and Fe$_3$O$_4$interfacial crystallites (50- -thick) coexist on the $\alpha$-AI$_2$O$_3$(0001) in the sputter-grown amorphous films at room temperature. The amorphous precursor is crystallized to the epitaxial $\alpha$-Fe$_2$O$_3$grains in three steps with annealing temperature; i ) the growth of the well aligned $\alpha$-Fe$_2$O$_3$interfacial crystallites, together with the transformation of the Fe$_3$O$_4$crystallites to the $\alpha$-Fe$_2$O$_3$ crystallites, ii ) the growth of the less aligned (3.08$^{\circ}$ FWHM)$\alpha$-Fe$_2$O$_3$grains on the well aligned grains (＞40$0^{\circ}C$), and iii) the nucleation of the other less aligned (1.39$^{\circ}$ FWHM) $\alpha$-Fe$_2$O$_3$grains directly on the $\alpha$-AI$_2$O$_3$substrate (＞$600^{\circ}C$). The effective thickness thinner than 230 may be very useful for enhancing the epitaxial quality of $\alpha$-Fe$_2$O$_3$/AI$_2$O$_3$(0001) thin films.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1430-1432
• /
• 2009

The effect of different annealing methods on the sheet resistance of indium tin oxide (ITO) on polyimide (PI) substrate has been investigated. As electro-annealing induced the predominant growth of crystallites of ITO thin films along (400) plane, the sheet resistance of ITO films that were electro-annealed for 2 mA at $180^{\circ}C$ considerably decreased from 50 to 28 ${\Omega}/cm^2$.

• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.659-667
• /
• 1997

The effect of calcination temperature of Mg(OH)2 on the green density and densification of MgO was investigated. It was observed that the impure magnesium hydroxide powder showed a higher crystallization rate while it had a lower tendency of agglomeration between periclae crystallites, as compared to that of the pure magnesium hydroxide powder. In the case of calcination of the powders under 85$0^{\circ}C$, the impure powder showed the higher green and sintered density. In spite of higher green density upon the calcination over 100$0^{\circ}C$, the impure powder showed the lower sintered density, caused by exaggerated growth of the periclase crystallites. The highest sintered densities in the both powders were obtained at the calcination temperature of 100$0^{\circ}C$. And the green density was inversely proportional to the sintered density at the calcination over 100$0^{\circ}C$.

• Journal of the Korean institute of surface engineering
• /
• v.18 no.2
• /
• pp.53-60
• /
• 1985

The microstructure of zine electrodeposits was investigated by using zinc sulfate solution in still bath. The cathode current efficiency decreased with increasing current density, and decreasing temperature. The preferred orientation of the zinc electrodeposits changed from (10.3) texture to(10.${\ell}$)-(00.1)(${\ell}$=1, 2, 3) texture through (10.2)-(10.3) preferred orientation with increasing cathode over potential. The surface morphology of zinc electrodeposits changed from the dendritic growth with granular crystallites to the blocks of hexagonal crystallites packed together with increasing current density. The microstructure of cross section of the above deposits are the rough granular structure and columnar structure respectively.

• Korean Journal of Metals and Materials
• /
• v.50 no.7
• /
• pp.539-544
• /
• 2012

Thermal shock behavior of TiN-coated SUS 304 substrate was investigated using a laser ablation method. By short surface ablation with a pulse Nd-YAG laser, considerable surface crack and spalling were observed, whereas there were few oxidation phenomena, such as grain growth of TiN crystallites, nucleation and growth of $TiO_2$ crystallites, which were observed from the coatings quenched from $700^{\circ}C$ in a chamber. The oxygen concentration of the ablated coating surface with the pulse laser also had a lower value than that of the quenched coating surface by Auger electron spectroscopy and electron probe micro analysis. These results were attributed to the fact that the properties of the pulse laser method have a very short heating time and so the diffusion time for oxidation was insufficient. Consequently, it was verified that the laser thermal shock test provides a way to evaluate the influence of the thermal shock load reduced oxidation effect.