• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.63-70
• /
• 2000

In 1925, H.J. Joosten was the first in the world to use chemical injection grouts composed of sodium silicate and calcium chloride. This unique development prompted the introduction of other chemical grouting techniques. Among these chemical grouting techniques, sodium silicate based grout has been the most widely used in the world, but it has not been generally considered to be a permanent material. Therefore, studies to improve the weak points of sodium silicate based grout have been conducted, and new applications of grout were recently developed. We also developed the micro fine hybrid silicate grout of suspention type which properties are sepecialized as the high strength and durability, according to the reactant of special sodium silicate grout and the high strength hardener. As the results of this study we could derive the 2 times over high strength of Micro fine hybrid Silicate grouting method(MS method) more than that of the ordinary sodium silicate grout. And also we could confirm that the alkali leakage of micro fine hybrid silicate grout is less than that of ordinary sodium silicate grout. So we could get the high strength and durability of hybrid silicate grout are superior to those of ordinary sodium silicate grout.

• 한국지반공학회논문집
• /
• 제18권5호
• /
• pp.229-236
• /
• 2002

본 논문은 실용화된 지반개량용 마이크로시멘트 및 보통포틀랜드시멘트의 주입특성에 관한 연구로서 기초물성, 고결율, 침투성과 같이 실험적으로 주입재의 입도와 다짐정도를 조정하고, 주입대상 토사지반의 투수계수를 3종류로 변화시컥 약액주입의 주요 특성을 검토한 것이다. 주입재의 적용성을 평가하기 위하여 고결성 시험 및 침투성 시험을 실시한 결과, 모형토사지반의 상대밀도에 따른 투수계수를 $10^{-4}$~$10^{-2}$cm/sec로 변화시킨 경우, 마이크로시멘트는 투수 계수 $10^{-4}$cm/sec에서 유효고결율 75%, 침투주입율 86%로서 침투성 및 고결성이 우수한 결과를 나타낸 반면, OPC는 $10^{-2}$cm/sec에서 유효고결율 및 침투주입율이 50% 미만으로서 원활한 침투주입이 될 수 없음을 알 수 있었다. 댐 기초 지반 및 연약지반의 보강을 위해 주입재의 침투성이 요구되는 경우에는 마이크로시멘트가 적용성이 매우 우수한 것으로 판단된다. 동수지중 모형시험 결과 유속이 상대적으로 느린 경우 주입압이 높을수록, 완결형 주입재가 고결효과가 우수한 반면, 유속이 빠른 경우에는 완결형의 경우 주입재의 대부분이 외부로 유출되는 등 유효고결율이 매우 낮아 고결효과가 불량함을 알 수 있었다.

• Journal of Ceramic Processing Research
• /
• 제19권6호
• /
• pp.509-513
• /
• 2018

This study uses fly ash for non-shrinkage grout in order to develop strength of grout and improve its durability. We grind fly ash to the extent of $7,000cm^2/g$ and use ground fly ash and raw fly ash respectively at the proportion of 10%, 20%, 30% instead of OPC and compare the results drawn on the condition of each proportion. As a mixed material of grout, EVA and water-reducing agent is added in order to prevent bleeding and improve segregation resistance, CSA is added with a view to preventing drying shrinkage and improving early strength property. In regard to flow and flow time test for analyzing and evaluating workability, it is revealed that grouts of all mix proportions except raw fly ash 30% mix proportion satisfy all performance criteria. With regard to length change rate, grout with no admixture shows the highest shrinkage rate, but the rate is 0.0005%, extremely insignificant rate. As material age increases, compressive strength of two grouts, that is to say ground fly ash 10% and 20%-used grouts, exceed that of grout with no admixture or show high-level compressive strength.

• 한국지반환경공학회 논문집
• /
• 제11권9호
• /
• pp.47-53
• /
• 2010

본 연구는 최근 개발된 실리카졸 그라우트재의 압축강도 특성을 규명한 것으로써 연구에 사용된 그라우트재는 3차원 겔형성재인 실리카졸 그라우트재와 규산나트륨 그라우트재에 대한 공학적 특성을 비교하기 위하여 일축압축강도시험(호모겔, 샌드겔), 투수시험, 휨강도시험등을 통해 강도 특성과 친환경성을 규명하고자 하였다. 실리카졸 그라우트재가 규산나트륨 그라우트재보다 초기(72시간 이내)에 일축압축강도가 3~5배 이상의 고강도로 증진되고 있음을 확인하였다. 샌드겔과 호모겔의 재령 28일의 일축압축강도로 비교 시 실리카졸 그라우팅제의 경우 샌드겔이 호모겔에 비해 약 1.3배 정도 강도가 높게 측정되었고, 이는 실리카졸의 경우 실제로 지반에 주입되어 사용되었을 경우 고강도를 발휘하는 특성이 있기 때문으로 추정된다. 투수시험 결과 실리카졸이 차수성면에서 현장에 적용하는데 무리가 없다고 판단되어 차수성을 요구하는 현장에 적용이 가능하다고 판단된다. 휨강도시험결과 그라우팅제용 실리카졸은 최종 28일 강도의 경우 규산나트륨 그라우팅제에 비해 3배 이상의 차이를 보이고 있다.

• 한국안전학회지
• /
• 제26권5호
• /
• pp.59-64
• /
• 2011

This paper presents the research results performed to develope the shrinkage-free grout with high early strength. Alumina cement and anhydrite were utilized as the expensive tool to gain the shrinkage-free grout. The compressive strength, length change, and ettringite formation of the grout were investigated with compressive test, length change test, and X-ray diffraction. The more anhydrite was added into the grout, the larger the early expansion of the grout. In addition, the more anhydrite formated the more ettringite. From this study, It was conformed that the grout mixture with shrinkage-free property and high early strength is the mixture with the ratio of alumina cement and anhydrite of 40:60 by weight.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.259-266
• /
• 2019

This paper presents a comparison between experimental measurements and numerical estimations of penetration length of a cement grout injected in discrete joints. In the experiment, a joint was generated by planar acryl plates with a certain separation distance (; aperture) and was designed in such a way to vary the separation distances. Since a cement grout was used, the grout viscosity can be varied by controlling water-cement (W/C) ratios. Throughout these experiments, the influence of joint aperture, cement grout viscosity, and injection rate on a penetration length in a discrete joint was investigated. During the experiments, we also measured the time-dependent variation of grout viscosity due to a hardening process. The time-dependent viscosity was included in our numerical simulations as a function of elapsed time to demonstrate its impact on the estimation of penetration length. In the numerical simulations, Bingham fluid model that has been known to be applicable to a viscous cement material, was employed. We showed that the estimations by the current numerical approach were well comparable to the experimental measurements only in limited conditions of lower injection rates and smaller joint apertures. The difference between two approaches resulted from the facts that material separation (; bleeding) of cement grout, which was noticeable in higher injection rate and there could be a significant surface friction between the grout and joint planes, which are not included in the numerical simulations. Our numerical simulation, meanwhile, could well demonstrate that penetration length can be significantly over-estimated without considering a time-dependency of viscosity in a cement grout.

• 한국지반환경공학회 논문집
• /
• 제24권1호
• /
• pp.15-23
• /
• 2023

그라우팅 공법은 연약지반의 차수 및 보강을 목적으로 시공되는 공법이다. 그라우트가 지반 내에 주입될 때, 지반을 구성하는 지반의 형태, 토립자의 크기, 공극율 및 지하수의 유무에 따라 그라우트가 침투 및 확산하는 형태가 다양하게 나타나고 있으나, 그라우팅 설계 시에는 이러한 요인을 적용하기 어려운 실정이다. 따라서, 본 연구에서는 전도성 재료를 함유한 그라우트를 지반내로 주입하는데 있어서 전도성 재료 첨가에 따른 그라우트의 침투 성능을 파악하기 위하여 실내시험을 수행하였다. 주입시험에서는 전도성 재료를 혼합수의 0%, 3% 및 5%를 그라우트에 첨가하고, 원지반 조건을 자갈과 규사로 구성된 다양한 지반으로 조성하였다. 전도성 그라우트는 전용주입장치를 사용하여 모형지반 내로 압력에 의해 주입되면서 주입시간(t), 압력(p), 유속(v) 및 주입량(q)를 계측하고, 모형지반 내 주입된 경화체를 채취하여 침투성능을 평가하였다. 그라우트 주입실험 결과에서는 전도성 재료의 사용량과 그라우트 주입율은 역의 관계를 나타내었으며, 모형지반 토립자 크기에 따라 침투형태가 변화되는 것을 확인하였다. 전도성 재료를 함유한 그라우트는 지반 내 침투가 비교적 양호하고 경화체의 강도 및 내구성이 우수하여 그라우트의 침투범위 측정을 위한 첨가제로 사용하는 것이 가능하다고 판단하였다.

• Geomechanics and Engineering
• /
• 제18권1호
• /
• pp.59-69
• /
• 2019

Grout injection is mainly used for permeability reduction and/or improvement of the ground by injecting grout material into pores, cracks, and joints in the ground. The oscillatory grout injection method was developed to enhance the grout penetration. In order to verify the level of enhancement of the grout, field grout injection tests, both static and oscillatory tests, were performed at three job sites. The enhancement in the permeability reduction and ground improvement effect was verified by performing a core boring, borehole image processing analysis, phenolphthalein test, scanning electron microscopy analysis, variable heat test, Lugeon test, standard penetration test, and an elastic wave test. The oscillatory grout injection increased the joint filling rate by 80% more and decreased the permeability coefficient by 33-68%, more compared to the static grout injection method. The constrained modulus of the jointed rock mass was increased by 50% more with oscillatory grout injection compared to the static grout injection, indicating that the oscillatory injection was more effective in enhancing the stiffness of the rock mass.

• KCI Concrete Journal
• /
• 제14권1호
• /
• pp.8-14
• /
• 2002

This is the first of two part series on experimental studies of grout type transverse joints. In this study, grout type transverse joints between precast concrete slabs are statically tested to determine the cracking loads and ultimate shear capacities of the grout type transverse joints. The tests are performed with a loading equipment designed and constructed especially in the lab to induce shear failures on the joints of the test specimens. Shape of the transverse joints, grouting materials and amount of prestress are selected as test parameters for the study. The results indicate that epoxy is an excellent grouting material which can be used in limited locations where large tensile stress is acting on the slab. Longitudinal prestressing is also an effective method to increase the shear strength of the transverse joints. A rational method to estimate the cracking and ultimate loads for the design of grout type transverse joints is proposed based on the static loading tests. Success of the tests with shear loading equipment allowed continuing the research further onto the fatigue strength of the grout type joints, which will be presented in the second part of the paper.

• KIEAE Journal
• /
• 제14권2호
• /
• pp.29-36
• /
• 2014

The ground source heat pump (GSHP) system has attracted much of attention, because of its stability of heat production and the high efficiency of the system. Performance of the heat exchanger is dependent on the soil temperature, the ground thermal conductivity, the operation schedule, the pipe placement and the design temperature. However, in spite of the many variables of these systems, there have been few research on the effect of the systems on system performance. In this study, analysis of the heat exchange rate according to soil temperature and grout material was conducted by numerical simulation. Furthermore, the heat distribution around the ground heat exchanger was presented on the different conditions of grout and underground temperature by the simulation.