• 한국전산유체공학회:학술대회논문집
• /
• 2008.08a
• /
• pp.37.4-37.4
• /
• 2008

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.253-254
• /
• 2002

Based on 3-D surface morphology measurements of C.G. irons, the fractal analyses were made on relationship between dry sliding surface morphology and the fractal dimension. It is revealed that the values of fractal dimensions ($D_f$) of sliding surfaces are in the range between 1-2, which are closely related to the surface morphologies. With the increase in depths of grooves or pits, the $D_f$ values increase. At the same time, the increases in densities of the grooves also cause the $D_f$ values to increase. At last, relationship among $D_f$ and friction coefficient as well as wear rate is discussed.

• Proceedings of the KSME Conference
• /
• 2001.06d
• /
• pp.252-259
• /
• 2001

It is derived for the temperature profile in a cylindrical and planar shape capillary pumped loop evaporators subject to a uniform heat flux prior to the initiation of boiling using the finite difference method. The results of the analysis allow for the determination of applied power levels for which nucleation is likely to occur only within the vapor grooves of the evaporator while maintaining subcooling in the liquid core, thereby increasing the likelihood of a successful startup. Also, limits are found for which additional increases in the applied heat flux do not increase the temperature difference between the vapor grooves and the wick-liquid core interface. Several advantages of larger diameter evaporators observed experimentally in startup are explained and quantified by the model. This analysis is appropriate for standard capillary pumped loop evaporators during a fully-flooded startup as well as starter pump designs and loop heat pipes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.4
• /
• pp.859-867
• /
• 1998

An oil lubricated Herringbone aroove jounal bearing(HGJB) with eight-circular-profile grooves on the non-rotating bearing surface is analyzed numerically and experimentally. The load carrying capacity, attitude angle, stiffness and damping coefficients are obtained numerically for the various bearing configurations. The onset speed of instability is also examined for the various eccentricity ratios. The configuration parameters of HGJB, such as groove depth ratio, groove width ratio, and groove angle, are dependent on each other because the grooves are generated by using eight small balls rolling over the inner surface of the sleeve with press fit. Therefore, it is not allowed to suggest a set of optimal design parameters such as the one for the rectangular profile HGJB. The overall results from numerical and experimental analysis prove that the circular profile HGJB has an excellent stability characteristics and the higher load carrying capacity than the plain journal bearing.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.107-110
• /
• 2005

Tribological behaviors of carbon epoxy composites whose surfaces have many small grooves were compared with respect to coating method under dry sliding and water lubricating conditions. The surface coating materials were epoxy (Ep) and polyethylene (PE) mixed with self-lubricating $MoS_2$ and PTFE powders. The wear morphology of the composites observed with a scanning electron microscopic (SEM) revealed that the surface coating layer mixed with the self-lubricating powder on the grooved surface significantly improved the wear resistance under water lubricating condition because the surface coating layer blocked water to penetrate the composite surface and the self-lubricating powder reduced the wear on the coating by suppressing the generation of blisters.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.31 no.8
• /
• pp.711-717
• /
• 2007

Shape optimization of a staggered herringbone groove micromixer using three-dimensional Navier-Stokes analysis has been carried using Kriging model. The analysis of the degree of mixing is performed by the calculation of spatial data statistics. The calculation of the variance of the mass fraction at various nodes on a plane in the channel is used to quantify mixing. A numerical optimization technique with Kriging model is applied to optimize the shape of the grooves on a single wall of the channel. Three design variables, namely, the ratio of groove width to groove pitch, the ratio of the groove depth to channel height ratio and the angle of the groove, are selected for optimization. A mixing index is used as the objective function. The results of the optimization show that the mixing is very sensitive to the shape of the groove which can be used in controlling mixing in microdevices.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.3
• /
• pp.291-298
• /
• 2014

This study uses two numerical approaches to analyze the filling behavior of micro patterns on micro-injection molding for V-grooves pattern which cannot be simulated with conventional CAE packages. The parametric studies have been performed to examine the fidelity of micro patterns with respect to temperature, pressure, inlet velocity and pattern location on the mold according to the boundary condition from the macro pressure and velocity data which can be obtained by conventional CAE packages. Through these numerical approaches, the filling behavior of polymer melt in micro patterns can be understood, the quality of replication can be predicted, and the V-groove pattern can be shaped uniformly during the process of injection molding.

• Textile Coloration and Finishing
• /
• v.13 no.5
• /
• pp.58-58
• /
• 2001

This study surveys the fiber behavior in yarn formation and the physical properties of Solo-spun yarn. The specimens were made by six types of Solo-spun rollers with fixed twist multiplier. The physical properties such as yarn count, evenness, strength, and breaking elongation of these yarns were compared with the properties of ring spun yarns and analysed with the mechanism of Solo-spun yarn formation. The grooves on the surface of Solo-spun roller divide the web and interfere the twist propagation. These phenomena cause the uneven draft and the fly of fiber, so the Solo-spun yarn becomes finer than fing-spun yarn and the yarn breaking strength and elongation deteriorate, but these demerits can be improved with rounding the protruded edge of Solo-spun roller grooves.

• Textile Coloration and Finishing
• /
• v.13 no.5
• /
• pp.346-352
• /
• 2001

This study surveys the fiber behavior in yam formation and the physical properties of Solo-spun yam. The specimens were made by six types of Solo-spun rollers with fixed twist multiplier. The physical properties such as yam count, evenness, strength, and breaking elongation of these yams were compared with the properties of ring spun yams and analysed with the mechanism of Solo-spun yarn formation. The grooves on the surface of Solo-spun roller divide the web and interfere the twist propagation. These phenomena cause the uneven draft and the fly of fiber, so the Solo-spun yam becomes finer than fing-spun yam and the yam breaking strength and elongation deteriorate, but these demerits can be improved with rounding the protruded edge of Solo-spun roller grooves.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.1005-1013
• /
• 1987

For the factory automation and unmanned machine operation, it is very important to manufacture highly reliable and efficient chip breakers for optimal chip control. In this research, using the CALMA CAD/CAM SYSTEM, the manufacturing process of 3-dimensional chip breakers is established. Using the results of the cutting test of the selected chip breakers with double-step grooves, the chip breaking mechanism is schematically analysed. An expression for the chip breaking relation is derived which considers chip material behavior following LUDWIK's stress-strain curve, chip breaking criterion and the shape of chip breakers. This contains the thickness of chip, the radius of chip curl, and the mechanical properties of chip materials. It is found that the expression agrees very closely with the experimental results.