• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.39-43
• /
• 1996

This paper described on the effect of residual stocks in internal grinding of tungsten carbide materials in order to improve the grinding efficiency as well as grinding accuracy. Though the fundamental investigation is carried out for tungsten carbide materials using electroplated diamond wheel, the residual stock after grinding process is effective to the grinding effciiency. The obtained results are as follows: (1) Under the depth of cut(t) is constant and decreasing the workpiece velocity(Vw), the resiudal stock after grinding is increased, but the difference is little less than the difference by table speed. (2) Increasing the wheel velocity, the residual stock after grinding is decreased. Therefore in order to minimize the residual stock, the wheel velocity should be increased as far as possible. (3) The surface foughness and out-of roundness increased with depth of cut and table speed, and decreased with wheel velocity, but it may as well adopt as much as polssible under the dimensional tolerance which is required for high efficiency grinding. (4) In order to remove residual stock, the spark-out grinding shoule be done, and it also can be improved about 20 .approx. 25% throughout spark-out grinding, and the number of optimal spark-out times were within 10 times.

• 한국공작기계학회논문집
• /
• 제10권3호
• /
• pp.1-6
• /
• 2001

An analytical thermal model of HESG(higt efficiency speed grinding) is presented, in which the heat flux to workpiece in grinding zone is modeled as time dependent and moves along a slope decided by contact chord(approximation of con-tact arc). By matching the maximum surface temperature of workpiece derived from this model to the maximum surface temperature of grinding wheel composite as done in Lavins simple thermal model, the relation of maximum surface tem-perature and energy partition of workpiece to grinding speed is obtained. In high speed grinding, as wheel speed increases, energy partition decreases with no regard to table speed.

• 한국세라믹학회지
• /
• 제40권7호
• /
• pp.696-701
• /
• 2003

교반형 볼 밀에서 실리카 분말의 열처리에 따른 분쇄효율을 분쇄에 따른 에너지 소비량을 측정함으로써 조사하였다. 열처리를 행한 것과 행하지 않은 시료를 비교해 보면, 600~90$0^{\circ}C$에서 열처리 후 실온에서 냉각된 시료를 건식 분쇄하였을 경우 약 40~50% 정도, 열처리 후 물속에서 급속 냉각한 경우 약 52～62% 정도의 에너지의 감소 효과가 있었다. 또한 열처리한 실리카 분말을 습식 분쇄를 할 경우 건식 분쇄에 비하여 약 40% 정도의 분쇄에너지가 적게 소모되고 있음을 알 수 있었다. 또한 실리카 분말을 열처리 한 후, 급속 냉각할 경우 발생하는 열충격은 입도에 대한 영향을 거의 받지 않으며 분쇄효과를 향상시킴을 알 수 있었다.

• 한국정밀공학회지
• /
• 제13권8호
• /
• pp.52-59
• /
• 1996

Conventionally, grinding of stainless steel, aluminium ally, copper alloy, and titanum alloy are difficult to obtain the high quality finish, because they have the mechanical properties such as low hardness, high toughness which result in the loading of wheel and the poor surface finish. Inorder to perform the grinding operations for these sorts of materials easily, the discontinuous grinding wheel with multi-porous grooves has newly been developed. The multi-porous grooves were formed during wheel production. This discontinous grinding wheel increases the grinding performance. It is desirable to use the discontinuous grinding wheel when grinding materials wiht high efficiency and accuracy which is impossible by conventional wheels. In this paper, the constructing and manufacturing method of grinding wheel with multi-proous grooves are explained, and the grinding charateristics of discontinuous grinding wheel are also illustrate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.272-276
• /
• 1993

We made to develop CNC Tool Grinding Machine automating the linear motion of X,Y,Z axis of table, and thetilting and rotation of tool holding vice by using Encorder to increase the efficiency of tool grinding for the Conventional Tool Grinding Machine. We did not consider the part of static, dynamic and thermal behavior that must necessary consider when wedesign, because we used existing Conventional Tool Grinding Machine as it is. We investigated simulation to make existing Conventional Tool Grinding Machine like CNC. We also designed it, and we compared the capability of existing Conventional Tool Grinding and CNC Tool Grinding Machine, and we investigated, too.

• 한국정밀공학회지
• /
• 제12권8호
• /
• pp.99-105
• /
• 1995

This paper provides a highly efficient grinding for ferrous materials using ELID-grinding method. The grinding efficiency using ELID gring method with CIFB-cBN wheel and CB-cBN wheel is compared with general grinding method with V-cBN wheel. This paper measured grinding ratio for plunge grinding and grinding resistance for traverse grinding in order to investigate grinding ability. The results show that ELID grinding methods is useful for the high efficient grinding of ferrous materials.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.204-209
• /
• 1999

The dressing time monitoring in cylindrical grinding is very important with respect to machining efficiency. Therefore, the purpose of this paper is to determine the wheel life by monitoring behavior of grinding power for Wa, 19A and GC. For this purpose, we investigated indirectly the attritious wear of grain edge, the loading of grinding wheel and the breakage of grain through the grinding power and the surface roughness under various grinding conditions. From obtained the results, the relationship between the wheel life and the average sectional chip area is examined to guide for the determination of dressing time.

• 한국기계가공학회지
• /
• 제14권2호
• /
• pp.19-24
• /
• 2015

Gears are produced through a variety of methods. In general, a metal piece is formed into the general shape of a gear through rough cuts. The gear then moves on to a more precise machine that removes more material. Grinders work via abrasion, rubbing a rough surface against a work piece at such high speeds that it literally scrapes unwanted material away from the item. Since the grinder is spinning so fast, the material is removed very quickly. This allows a grinder to remove a very small amount without taking any unwanted material with it. This study investigates the effect of grinding process parameters like grinding spindle speed and table transfer speed on the gear grade and grinding efficiency.

• Tribology and Lubricants
• /
• 제34권6호
• /
• pp.209-216
• /
• 2018

Sapphire is a substrate material that is widely used in optical and electronic devices. However, the processing of sapphire into a substrate takes a long time owing to its high hardness and chemical inertness. In order to process the sapphire ingot into a substrate, ingot growth, multiwire sawing, lapping, and polishing are required. The lap grinding process using pellets is known as one of the ways to improve the efficiency of sapphire substrate processing. The lap grinding process ensures high processing efficiency while utilizing two-body abrasion, unlike the lapping process which utilizes three-body abrasion by particles. However, the lap grinding process has a high material removal rate (MRR), while its weakness is in obtaining the required surface roughness for the final polishing process. In this study, we examine the effects of free abrasives in lap grinding on the material removal characteristics of sapphire substrate. Before conducting the lap grinding experiments, it was confirmed that the addition of free abrasives changed the friction force through the pin-on-disk wear test. The MRR and roughness reduction rate are experimentally studied to verify the effects of free abrasive concentration on deionized water. The addition of free abrasives (colloidal silica) in the lap grinding process can improve surface roughness by three-body abrasion along with two-body abrasion by diamond grits.

• 한국생산제조학회지
• /
• 제7권5호
• /
• pp.59-65
• /
• 1998

In order to utilize the information of well-know grinding database or grinding machine characteristics, a database needs to be designed by considering the delicate property of the machine tools for the high precision and quality of the demanding specification. Among the machine tools for the high precision and quality of the demanding specification. Among the machine tools, machining conditions of the grinding are various and knowledge repeatance obtained form the grinding process are less credable. therefore it is desirable for database, which is used to set the grinding conditions, to utilize the maximum machine tool capability. The present paper studied on the occurance limit of chatter vibration and burn considering the characteristics of machine tool. And also basic experiments were performed to establish the optimum grinding conditions which could maximize the grinding efficiency.