• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.116-120
• /
• 2011

In this paper, we studied the optimization of the screen pringting method for crystalline silicon solar cell fabrication. The 156 * 156 mm2 p-type silicon wafers with $200{\mu}m$ thickness and $0.5-3{\Omega}cm$ resistivity were used after texturing, doping, and passivation. Screen printing method is a common way to make the c-Si solar cell with low-cost and high-efficiency. We studied the optimized condition for screen printing with crystalline silicon solar cell as changing the printing direction (finger line or bus bar), finger width, and mesh angle. As a result, the screen printing with finger line direction showed higher finger height and better conversion efficiency, compared with one with bus bar direction. The experiments with various finger widths and mesh angles were also carried out. The characteristics of solar cells was obtained by measuring light current-voltage, optical microscope and electroluminescence.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.4
• /
• pp.321-329
• /
• 2015

The static synchronous compensator (STATCOM) of cascaded H-bridge configuration accompanying multiple separate DC sides is inherently subject to the problem of uneven DC voltages. These DC voltages in one leg can be controlled by adjusting the AC-side output voltage of each cell inverter, which is proportional to the active power. However, when the phase current is extremely small, large AC-side voltage is required to generate the active power to balance the cell voltages. In this study, an alternative zero-sequence current injection method is proposed, which facilitates effective cell balancing controllers at no load, and has no effect on the power grid because the injected zero sequence current only flows within the STATCOM delta circuit. The performance of the proposed method is verified through simulation and experiments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.5A
• /
• pp.517-525
• /
• 2008

In this paper, we cary out system level simulations to investigate the effect of cell shape(i.e., different base station displacements in the two directions defined by the street grid) on minimizing transmitter power, interference power, and blocking probability for CDMA system in urban microcellular environments. In urban microcell, path loss to the base station depends on the orientation of the street where the mobile is located. Interference from mobile stations to the base station in the reference cell is considered up to second tier. The wrap around method is used to include the second tier interference with realistic computational complexity without reducing the accuracy of interference calculations. The investigation shows that the transmitter power, interference power, and blocking probability in a cell can be reduced by proper selection of the efficient cell shape.

• Journal of Navigation and Port Research
• /
• v.45 no.5
• /
• pp.231-237
• /
• 2021

Enhancing the performance of maritime wireless communication has been highlighted by the issue of cell planning in the sea area because of lack of an appropriate Propagation Loss Model (PLM). To resolve the cell planning issue in vast sea areas, it was essential to develop the (PLM) matching the intended sea area. However, there were considerable gaps between the prediction of legacy PLMs and field measurement in propagation loss and there was a need to develop the adjusted PLM (A-PLM). Therefore, cell planning was performed on this adjusted model, including modification of the base station's location, altitude, and antenna azimuth to meet the quality objectives. Furthermore, in order to verify the availability of the cell planning, Communication Service Quality Monitoring System (CS-QMS) was developed in the LTE-Maritime project to collect LTE signal quality information from the onboard equipment at regular intervals and to ensure that the service quality was high enough to satisfy the goals in each designated grid. As a result of verification, the success rate of RSRP was 95.7% for the intensive management zone (IMZ) and 96.4% for the interested zone (IZ), respectively.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.11 no.4
• /
• pp.10-21
• /
• 2008

A forest functions classification map is an essential element for the management planning of national forests. This study was intended to make out the map at the stand level by utilizing the Forest Functions Evaluation Program(FFEP), developed by Korea Forest Research Institute. In this program, the potential of each function was evaluated in each grid cell, and then a forest functions estimation map was generated based on the optimum grid cell values in each sub-compartment unit. Finally, the program produced a forest functions classification map with consideration of the priority of the functions. The final forest functions classification map required for the national forest management planning made out overlapping those results which the rest of the forest classified referring priority functions classification map to national forest manager and classified according to the local administrative guidance and sustainable forest resources management guidance. The results indicated that the forest function classification using the FFEP program could be an efficient tool for providing the data required for national forest management planning. Also this study made a meaningful progress in the forest function classification by considering the local forest administrative guidance and sustainable forest resources management guidance.

• KIPS Transactions on Computer and Communication Systems
• /
• v.6 no.5
• /
• pp.239-246
• /
• 2017

Communications for mobile sink groups such as rescue teams or platoons bring about a new challenging issue for handling group mobility in wireless sensor networks. Recently, a group region-based approach has been proposed to send data to a mobile sink group. However, it uses excessive flooding for 3 steps (group region discovery, region information notification, and data dissemination) to support mobile sink group. Thus, it causes high energy consumption and data delivery failure. Moreover, its per-sink mobility supporting scheme makes energy consumption and data delivery failure more serious. Thus, this paper proposes an Energy-efficient and Reliable Mobile Group communication protocol (ERMG) to support a mobile sink group, which exploits a virtual grid structure. For the group region discover and notification and the data dissemination, ERMG uses communications with only cell heads of grid cells that manages group sinks. ERMG also uses a per-grid based scheme to support sink mobility. Simulation results show that ERMG has 30% less energy consumption and 6% more desired delivery deadline success ratio than the existing protocols.

• Solar Energy
• /
• v.17 no.4
• /
• pp.3-11
• /
• 1997

Because grain boundaries in polycrystalline silicon act as potential barriers and recombination centers for the photo-generated charge carriers, these defects degrade conversion effiency of solar cell. To reduce these effects of grain boundaries, we investigated various influencing factors such as thermal treatment, various grid pattern, selective wet etching for grain boundaries, buried contact metallization along grain boundaries, grid on metallic thin film. Pretreatment above $900^{\circ}C$ in $N_2$ atmosphere, gettering by $POCl_3$ and Al treatment for back surface field contributed to obtain a high quality poly-Si. To prevent carrier losses at the grain boundaries, we carried out surface treatment using Schimmel etchant. This etchant delineated grain boundaries of $10{\mu}m$ depth as well as surface texturing effect. A metal AI diffusion into grain boundaries on rear side reduced back surface recombination effects at grain boundaries. A combination of fine grid with finger spacing of 0.4mm and buried electrode along grain boundaries improved short circuit current density of solar cell. A ultra-thin Chromium layer of 20nm with transmittance of 80% reduced series resistance. This paper focused on the grain boundary effect for terrestrial applications of solar cells with low cost, large area, and high efficiency.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.3
• /
• pp.371-375
• /
• 2013

A new model about output power prediction of PV module with various tilted angles and cell to cell distances has been proposed in this paper. Light intensity arrived on a solar cell could be changed by characteristics of PV module materials. Refractive indices, thickness and absorption coefficients of glass, EVA, solar cell and Backsheet are used to predict output. Also, the incident angle of light is changed 0 to 90[$^{\circ}$] and cell to cell distances are 5, 10 15[mm]. Two types of light incident on a solar cell are considered which are direct to a solar cell and reflected from Backsheet. The intensity of the incident light directly into the solar cell is reduced through glass and EVA about 17.5[%] in theoretical way. It has an error of 2.26[%] compared with experimental result. The results for compare theoretical with experimental data is validated within the error of 6.3[%]. This paper would be a research material to predict output power when the PV module is installed outdoor or a building.

• Journal of Electrical Engineering and information Science
• /
• v.2 no.5
• /
• pp.65-71
• /
• 1997

We present heterojunction solar cells with a structure of metal/a-Si:H(n-i-p)/poly-Si(n-p)/metal for the terrestrial applications. This cell consists fo two component cells: a top n-i-p junction a-Si:Hi cell with wide-bandgap 1.8eV and a bottom n-p junction poly-Si cell with narrow-bandgap 1.1eV. The efficiency influencing factors of the solar cell were investigated in terms of simulation an experiment. Three main topics of the investigated study were the bottom cell with n-p junction poly-Si, the top a-Si:H cell with n-i-p junction, and the interface layer effects of heterojunction cell. The efficiency of bottom cell was improved with a pretreatment temperature of 900$^{\circ}C$, surface polishing, emitter thickness of 0.43$\mu\textrm{m}$, top Yb metal, and grid finger shading of 7% coverage. The process optimized cell showed a conversion efficiency about 16%. Top cell was grown by suing a photo-CVD system which gave an ion damage free and good p/i-a-Si:H layer interface. The heterojunction interface effect was examined with three different surface states; a chemical passivation, thermal oxide passivation, and Yb metal. the oxide passivated cell exhibited the higher photocurrent generation and better spectral response.

• Journal of Korea Water Resources Association
• /
• v.48 no.11
• /
• pp.937-944
• /
• 2015

This study proposed a novel technique, namely the Radar Polygon Method (RPM), for areal rainfall estimation based on radar precipitation data. The RPM algorithm has the following steps: 1. Determine a map of the similar rainfall occurrence of which each grid cell contains the binary information on whether the grid cell rainfall is similar to that of the observation gage; 2. Determine the similar rainfall probability map for each gage of which each grid cell contains the probability of having the rainfall similar to that of the observation gage; 3. Determine the governing territory of each gage by comparing the probability maps of the gages. RPM method was applied to the Anseong stream basin. Radar Polygons and Thiessen Polygons of the study area were similar to each other with the difference between the two being greater for the rain gage highly influenced by the orography. However, the weight factor between the two were similar with each other. The significance of this study is to pioneer a new application field of radar rainfall data that has been limited due to short observation period and low accuracy.