• 한국군사과학기술학회지
• /
• 제13권5호
• /
• pp.717-724
• /
• 2010

The initial trajectory of a spheroid configuration bobbin for precision guidance has been investigated by analyzing its aerodynamic load and six-degree-of-freedom motion. The effects of changes in the spheroidal head configuration, flow angle and lateral center-of-gravity offset are numerically studied using the commercial software "FLUENT". A wind tunnel test is also conducted to validate the numerical scheme and to examine effect of the Reynolds number on the flow around the bobbin. It is shown that the size of the separation bubble formed on the surface decreases significantly when the Reynolds number is varied between 110,000 and 140,000. At a zero flow angle, an oblate spheroidal head shows relatively moderate rotation while a prolate spheroidal head shows rapid rotation. The bobbin with a spherical head shape has little effect on the flow direction; however, the oblate bobbin is sensitive to the flow angle. The roll motion of the bobbin is greatly influenced by the lateral center-of-gravity offset and maximum dispersion is observed at half of the radius.

• 물과 미래
• /
• 제29권1호
• /
• pp.163-179
• /
• 1996

본 연구에서는 일차원 St. Venat 방정식을 이용하여 한강 하류부(고안-인도교 구간)의 홍수류 특성을 분석하였다. 유한차분 모형인 NETWORK모형을 이용하여 운동량 방정식의 각항(국부가속도항, 대류가속도항, 압력항, 중력항, 마찰항)의 절대적 크기와 상대적 크기를 비교 분석하였다. 분석결과 국부가속도항과 대류가속도항이 작게 나타나고 중력항, 압력항, 마찰항 등이 대부분의 구간에서 크게 나타나서 이 세 항이 흐름을 결정하는 주요 항임을 확인할 수 있었으며 수문곡선의 상태와 하도구간에 따라서는 국부가속도항과 대류가속도항의 상대적인 비율이 무시할 수 없을 정도로 크게 나타나서 이 구간에서는 동역학적 모형이 적절한 것으로 나타났다.

• Nuclear Engineering and Technology
• /
• 제31권5호
• /
• pp.476-485
• /
• 1999

In order to evaluate the gravity-injection capability to maintain core cooling after a loss-of-shutdown-cooling event during shutdown operation, the plant conditions of the Yong Gwang Units 3&4 were reviewed. The six cases of possible gravity-injection paths from the refueling water tank (RWT) were identified and the thermal-hydraulic analyses were performed using the RELAP5/MOD3.2 code. The core cooling capability was significantly dependent on the gravity-injection path, the RCS opening, and the injection rate. In the cases with the pressurizer manway opening higher than the RWT water level, the coolant was held up in the pressurizer and the system pressure continued increasing after gravity-injection. The gravity injection eventually stopped due to the high system pressure and the core was uncovered. In the cases with the injection path and opening on the same leg side, the core cooling was dependent on whether the water injected from the RWT passed the core region or not. However, in the cases with the injection path and opening on the different leg side, the system was well depressurized after gravity-injection and the core boiling was successfully prevented for a long-term transient. In addition, from the sensitivity study on the gravity-injection flow rate, it was found that about 54 kg/s of injection rate was required to maintain the core cooling and the core cooling could be provided for about 10.6 hours after event with that injection rate from the RWT. Those analysis results would provide useful information to operators coping with the event.

• 한국생산제조학회지
• /
• 제19권1호
• /
• pp.57-64
• /
• 2010

Metal Injection Molding (MIM) is attractive because it produces consistent, complex-geometry components for high-volume, high-strength, and high-performance applications. Also MIM using in optical communication field, display field, and semi-conductor field is a cost-effective alternative to metal machining or investment casting parts. It offers tremendous single-step parts consolidation potential and design flexibility. The objective of this paper is to study the suitability of design, flow analysis, debinding and sinterin processes, and capability analysis. The suitable injection conditions were 0.5~1.5 second filling time, 11.0~12.5 MPa injection pressure derived from flow analysis. The gravity of the product is measured after debinding an sintering. The maximum and minimum gravity levels are 7.5939 and 7.5097. the average and standard deviation are 7.5579 and 0.0122; when converted into density, the figure stands at 98.154%. According to an analysis of overall capacity, PPM total, which refers to defect per million opportunities(DPMO), stands at 166,066.3 Z.Bench-the sum of defect rates exceeding the actual lowest and highest limits-is 0.97, which translates into the good quality rate of around 88.4% and the sigma level of 2.47.

• 대한기계학회논문집B
• /
• 제38권1호
• /
• pp.9-16
• /
• 2014

본 논문은 경사진 원형관에서 표면장력과 중력으로 구동되는 비뉴턴 유체(멱법칙 모델)의 유동 및 변위를 이론적으로 연구한 것이다. 그리고 표면장력에 의하여 연속적으로 원형관 내로 유입되는 비뉴턴 유체의 변위를 기술하기 위한 지배방정식을 처음으로 개발하였다. 뉴턴의 운동방정식으로부터 유도된 식은 2계 비선형이며 비제차인 형태의 상미분 방정식이다. 지배방정식의 해를 수평관에서 변위를 시간의 함수로 기술한 식 및 실험과 비교한 결과 정량적으로 동일한 일치를 보였다. 여기에 더하여 정상상태인 힘의 균형식의 결과에 대해서도 정확한 일치로 나타남을 확인할 수 있었다.

• 한국재료학회지
• /
• 제14권11호
• /
• pp.775-779
• /
• 2004

For improvement of heat dissipation performance, heat analysis is conducted on the newly designed heat sinks under two convection conditions by using computational fluid dynamics(CFD). Three types of heat sink, plate, wave and top vented wave, are used, and convection conditions are the variations of gravity direction at natural convection and of fan location at forced convection. The results of analysis showed that the heat resistances of top vented wave heat sink were $0.17^{\circ}C$/W(forced convection) and $0.48^{\circ}C$/W(natural convection). In the case of natural convection, gravity direction affected heat flow change, and protection against heat performance was superior in case of z-axis gravity direction. Under the forced convection, all the heat sinks revealed superior thermal characteristics in the fan position of z-axis rather than y-axis. In this study, it was observed that the top vented wave type heat sink showed the best ability of heat radiation comparing with the others.

• 한국수소및신에너지학회논문집
• /
• 제25권4호
• /
• pp.449-458
• /
• 2014

The heat transfer phenomenon was investigated in this study when a single round water jet with the low velocity and against the direction of gravity flows to the downward facing Isothermal of definite thickness circular plate. Experimental investigation is performed for a single round jet diameter 4mm, 6mm, and 8mm with the jet velocity 2.4m/s and jet fluid temperature of $24^{\circ}C$, varied the ratio of nozzle clearance/nozzle diameter (H/D)1, 2, 3, 6, and 8, on circular plate isothermal condition with $85^{\circ}C$. The local convection heat transfer coefficient distributions are analyzed based on the visualization of jet flow field. The effects of the diameter of Nozzle, the ratio of H/D and the ratio of nozzle diameter/circular plate diameter on heat transfer phenomenon are investigated. As a results of experiment is obtained correlation equation, $Nu_r=3.18Re_r^{0.55}Pr_r^{0.4}$.

• 자원환경지질
• /
• 제44권6호
• /
• pp.493-502
• /
• 2011

본 연구는 지형자료와 Free-air 중력이상을 이용하여 한반도의 모호면 심도 및 지각두께를 계산하였다. Airy-Heiskanen 지각평형 가설에 근거한 Free-air 중력이상에 포함된 지형중력과 연관성 있는 성분들을 파동수상관분석으로 추출하고 이로부터 보상이 이루어진 상태의 중력효과를 계산하였다. 계산된 결과로부터 반복법을 통한 역산을 이용하여 지각과 맨틀의 경계면인 모호면 심도를 도출하였고 역산 시 기존에 연구된 지진파에 의한 20개의 모호면 심도를 활용하여 포텐셜 필드에서 나타날 수 있는 비유일성의 가능성을 최소화하였다. 최종적으로 모호면 심도와 고도 자료를 더하여 한반도 지각두께를 도출하였으며 한반도 평균지각두께는 32.15 km, 표준편차 3.12 km를 나타내었다. 이 연구에서 구한 남한지역의 모호면과 같은 지역의 타 논문결과들과 비교하였을 때 평균 모호면 심도는 각각 31.08 km, 31.96 km, 33.02 km을 나타내고 표준편차는 1.94 km, 1.62 km, 1.77 km을 나타냄으로 각 연구결과의 통계치는 거의 일치하는 것으로 나타났고 모호면 굴곡 역시 공통적으로 태백산맥과 소백산맥을 따라 모호면이 깊어지고 경상분지는 얕아짐을 확인하였다. 또한 지각 내 중력 이상체의 분포에 대한 정보를 포함하고 있는 지형과 비상관된 Freeair 중력이상을 가지고 지열류량분포와 비교하였다. 저주파성분의 지형과 비상관된 Free-air 중력이상과 지열류량분포를 상관 비교한 결과 높은 양의 상관관계를 나타냈고, 특히, 경상분지지역은 높은 지열류량분포가 암석의 밀도보상으로 인해 모호면의 상승을 가져다 준 것으로 보인다. 이러한 결과는 최근 Kim et al.(2008)에서 언급한 경상분지의 높은 지열류량이 맨틀로부터 야기되는 모델과 부합된다는 사실을 뒷받침해주고 있다.

• 한국안전학회지
• /
• 제30권6호
• /
• pp.18-25
• /
• 2015

Computational study of a gravity current prior to the backdraft was conducted using fire dynamic simulator (FDS). Various initial conditions of mixture compositions and compartment temperature as well as four opening geometries (Horizontal, Door, Vertical, and Full opening) were considered to figure out their effects on the gravity current. The density difference ratio (${\beta}$) between inside and outside of compartment, the gravity current time ($t_{grav}$) and velocity ($v_{grav}$), and non-dimensional velocity ($v^*$) were introduced to quantify the flow characteristics of the gravity current. Overall fluid structure of the gravity current at the fixed opening geometry showed similar development process for different ${\beta}$ conditions. However, $t_{grav}$ for entering air to reach the opposed wall to the opening geometry increased with ${\beta}$. Door, Vertical, and Horizontal openings where openings are attached on the ground showed similar development process of the gravity current except for Horizontal opening, which located on the middle of the opening wall. The magnitude of $v_{grav}$ at fixed ${\beta}$ was, from largest to smallest, Full > Vertical > Door > Horizontal, but it depended on both the size and location of the opening. On the other hand, $v^*$ was found to be independent to ${\beta}$, and only depended on the geometry of the opening.

• 자원환경지질
• /
• 제32권2호
• /
• pp.177-187
• /
• 1999

Gravity, magnetic and VLF surveys were conducted to investigat the structural stability and hazards associated with the Ubong landfill in Pohang City, which has been built to dump industrial wastes. In 1994, the collapse of a bank happened in the 6th landfill site due to sudden heavy rain, and a large quantity of waste materials flowed out to the nearby landfill sites, factories and roads. We used $10{\times}10m$ resolution DEM data for gravity reductions. The maximum variation of the terrain effect in the survey area is about 0.5 mgal and the terrain effect is large in the vicinity of bank boundary. The Bouguer gravity anomaly map shows the effect due to the variatino of thickness and type of waste materials. The small negative gravity anomaly increases from the 9th site to the 6th site. The small negative gravity anomaly of the 9th site reflects the relatively shallow dumping depth of average 14.5 m in this site and increased density of waste materials by the repeated stabilization process of soil overlaying. The 6th site is located at the center of the former valley and rainfall and groundwater are expected to flow from south-east to north-west. Therefore, considering the previous accident of mixing waste and bank materials at the north-west boundary of the landfill, there may be some environmental problems of leakage of contaminated water and bank stability. The complex inversion technique using Simulated annealing and Marquardt-Levenberg methods was applied to calculate three-dimensional density distribution from gravity data. In the case of 6th site, it is apparent that the landfill had been dumped in four sectors. However, most part of the 9th site and showed that high magnetic industrial wastes were concentrated in the 6th site. The result of magnetic survey showing low magnetic anomalies along the boundaries of two sites is similar to that of gravity data. The VLF data also reveals four divided sectors in the 6th site, and overall anomaly trend indicates the directio of former valley.