• Journal of Korea Foundry Society
• /
• v.17 no.3
• /
• pp.267-275
• /
• 1997

Fabrication of high strength Mg-Li-Al alloys by squeeze casting was established by the stabilization of melt and mold temperatures, applied pressure and the refining method. The entrapment of inclusions during pouring was prevented using 30 ppi alumina foam filter. The as-cast microstructure consists of a mixture of ${\alpha}$ and ${\beta}$ phases including AILi and $MgLi_2$, Al particles, which are distributed in the ${\beta}$ matrix. The grain sizes of gravity and squeeze casting alloys were 288 ${\mu}m$ and 207 ${\mu}m$ respectively. The addition of Al in Mg-Li alloys promoted the formation of second phase particles, which were adjusted to optimize the properties of Mg-Li-Al alloys. The Mg-10wt%Li-5wt%Al alloy after heat treatment at $350^{\circ}C$ for 1 hour showed the maximum hardness value. This is due to the facts that the amounts of ${\alpha}$ and ${\beta}$ phases and their distributions are dependent upon the solution treatment temperature, and that the amounts of AILi and $MgLi_2Al$ particles are dependent upon the Al content.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.1
• /
• pp.57-64
• /
• 2010

Metal Injection Molding (MIM) is attractive because it produces consistent, complex-geometry components for high-volume, high-strength, and high-performance applications. Also MIM using in optical communication field, display field, and semi-conductor field is a cost-effective alternative to metal machining or investment casting parts. It offers tremendous single-step parts consolidation potential and design flexibility. The objective of this paper is to study the suitability of design, flow analysis, debinding and sinterin processes, and capability analysis. The suitable injection conditions were 0.5~1.5 second filling time, 11.0~12.5 MPa injection pressure derived from flow analysis. The gravity of the product is measured after debinding an sintering. The maximum and minimum gravity levels are 7.5939 and 7.5097. the average and standard deviation are 7.5579 and 0.0122; when converted into density, the figure stands at 98.154%. According to an analysis of overall capacity, PPM total, which refers to defect per million opportunities(DPMO), stands at 166,066.3 Z.Bench-the sum of defect rates exceeding the actual lowest and highest limits-is 0.97, which translates into the good quality rate of around 88.4% and the sigma level of 2.47.

• Transactions of Materials Processing
• /
• v.13 no.7
• /
• pp.608-613
• /
• 2004

Mechanical properties of hypereutectic Al-Si alloy are influenced by the size and distribution of primary Si. To investigate the effects of P addition and holding time, hypereutectic Al-Si alloys with various amount of P content were produced in the lab. Then, the size and distribution of primary Si were examined respectively. Mechanical properties of hardness, tensile strength and wear resistance were analyzed in conjunction with the microstructural variations in alloys.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.4
• /
• pp.244-252
• /
• 1994

The morphological changes of primary solid particles as a fuction of process time on Al-Si alloys during semi-solid state processing with a shear rate of 200s were studied. In hypereutectic Al-15.5wt%Si alloy, it was observed that primary Si crystals are fragmented in the early stage of stirring and morphologies of primary Si crystals change from faceted to spherical during isothermal shearing for 60 minutes. In quaternary Al-12.5wt%Si-2.9wt%Cu-0.7wt%Mg alloy system, it was observed both primary silicon and ${\alpha}$-alumunum particles. Microstructural evolution of primary Si crystals was similar to that of the hypereutectic Al-Si alloy but equiaxed ${\alpha}$-Al dendrites are broken into nearly spherical at the early stage of shearing and later stage of the isothermal shearing ${\alpha}$- Al particles are slightly coarsoned by Ostwald ripening. Mechanical properties of Al-Si-Cu-Mg alloy were compared to those from other processes (squeeze casting and gravity casting). After T6 heat treatment, comparable values of hardness were obtained while slightly lower compressive strength values were observed in rheocast alloy. The elongation, on the other hand, exhibited significant increasement of 15% over gravity cast alloy.

• Transactions of the Korean hydrogen and new energy society
• /
• v.15 no.3
• /
• pp.250-256
• /
• 2004

Magnesium and its alloys have the high potential as hydrogen storage materials because of their highest hydrogen storage capacity, low density and abundant resources. But poor kinetic properties of hydriding and dehydriding and high working temperature have limited their practical applications. In this study, the Mg-Ni binary alloys with different amount of Ni were produced by gravity casting and characterized in order to investigate the relationship between the microstructures and hydriding properties. The maximum hydrogen absorption capacity decreased, but the absorption kinetics increased with Ni content. The difference in the absorption kinetics was resulted from the differences in the sort and shape of primary solid phases and eutectic microstructure.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.320-324
• /
• 2015

Optimization of the fabrication process of NiO-yttrium doped barium zirconate (BZY) composite anode substrates using tape-casting for high performance thin-film protonic ceramic fuel cells (PCFCs) is investigated. The anode substrate is composed of a tens of microns-thick anode functional layer laminated over a porous anode substrate. The macro-pore structure of the anode support is induced by micron-scale polymethyl methacrylate (PMMA) pore formers. Thermal gravity analysis (TGA) and a dilatometer are used to determine the polymeric additive burn-out and sintering temperatures. Crystallinity and microstructure of the tape-cast NiO-BZY anode are analyzed after the sintering.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.3
• /
• pp.97-103
• /
• 2018

The objective of this study is to develop the mechanical properties of AlSiCu aluminum alloy by the two-step solution heat treatment. The microstructure of gravity casting specimen represents a typical dendrite structure having a secondary dendrite arm spacing (SDAS) of 40 mm. In addition to the Al matrix, a large amount of coarsen eutectic Si phase, $Al_2Cu$ intermetallic phase, and Fe-rich phases are generated. The eutectic Si phases are fragmented and globularized with solution heat treatment. Also, the $Al_2Cu$ intermetallic phase is resolutionized into the Al matrix. The $2^{nd}$ solution temperature at $525^{\circ}C$ might be a optimum condition for enhancement of mechanical properties of AlSiCu aluminum alloy.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.427-432
• /
• 2001

In this study, crushed sand is blended with river sand and sea sand, to investigate the quality change of antiwashout underwater concrete with variation of blend ratio of crushed sand(0%, 20%, 40%, 60%, 80%, 100%). To see experiment conclusion, the more blend ratio of crushed sand increases, the more unit weight increases. Because the for that specific gravity of crushed sand is higher comparatively than that of river sand and sea sand. Higher compressive strength is measured following the order of river sand, crushed sand, sea sand regardless of age and casting-curing condition. Except for case of using river sand, blend ratio of 40% is appeared on most compressive strength. So the optimum blend ratio of crushed sand is 40% from the view point of compressive strength.

• Journal of Korea Foundry Society
• /
• v.32 no.3
• /
• pp.150-156
• /
• 2012

발포금속은 초경량 재료로서 폐기공과 개기공의 두 가지 형태의 구조를 지니고 있으며 폐기공은 내충격성, 흡음성, 단열성의 기능을 지니고 있고, 개기공은 필터, 생체지지대, 촉매재, 열방출재 등으로 사용되고 있다. 개기공발포재는 삼차원 구조모양으로 프리커서를 이용한 압력정밀주조나 기공입자용출법으로 제조하고 있으나 기공의 크기나 셀의 형상, 두께 등을 조절하기에 어려움이 있다. 이를 해결하기 위하여 환경친화적인 펄라이트를 사용하여 목적하는 크기의 그래뉼을 제조한 후, 용융마그네슘합금을 감압주조법으로 주조하여 그래뉼의 크기로 기공율을 조절하고, 주형의 온도와 압력에 따른 유동의 길이를 측정하였다. 그래뉼 직경이 2.3 $mm{\O}$ 일때에 주형의 온도 $300^{\circ}C$ 이상, 압력이 5000 Pa 이상에서 유동길이 6.5 cm 이상을 얻었다.

• Journal of Korea Foundry Society
• /
• v.10 no.3
• /
• pp.247-253
• /
• 1990

주철의 중력금형주조에서 반복작업에 따른 응고과정의 변화를 3차원의 수치해석적 방법에 의하여 컴퓨터해석을 하였다. 수치해석적 방법으로는 차분법을 채택하였다. 반복작업과정에 따라 변화되어지는 주물의 응고시간과 미세조직, 기계적성질과의 관계가 조사 되어졌다. 컴퓨터에 의해 계산된 각싸이클의 냉각속도로 부터 주물의 공정셀의 수, 경도, 인장강도등의 변화를 예측하였으며 또한 반복싸이클에 따른 금형 및 주물의 온도분포와 최종응고부위등을 예측하였고 이들은 실제주조시험에서 얻어진 결과와 비교적 잘일치하였다. 중력금형주조에서 회주철의 응고시간, 공정셀, 기계적성질 및 응고속도에 미치는 냉각수의 영향이 또한 컴퓨터해석에 의하여 잘예측되었으며 컴퓨터해석에 의한 냉각수 라인의 적절한 설계에 의하여 주물의 미세조직 및 기계적성질과 결함발생 가능위치를 효과적으로 제어할수 있음을 확인하였다.