• Journal of radiological science and technology
• /
• v.29 no.4
• /
• pp.249-255
• /
• 2006

Purpose: The diagnostic utility of fluorine-18 2-deoxy-D-glucose positron emission tomograhpy ($^{18}F-FDG $PET) for the non-invasive differentiation of focal lung lesions originated from cancer or inflammation disease by combined visual image interpretation and semi-quantitative uptake value analysis has been documented. In general, Standardized Uptake Value(SUV) is used to diagnose lung disease. But SUV does not contain dynamic information of lung tissue for the glucose. Therefore, this study was undertaken to hypothesis that analysis of dynamic kinetics of focal lung lesions base on $^{18}F-FDG$ PET may more accurately determine the lung disease. So we compared Time Activity Curve(TAC), Standardized Uptake Value-Dynamic Curve(SUV-DC) graph pattern with Glucose Metabolic Rate(MRGlu) from Patlak analysis. Methods: With lung disease, 17 patients were examined. They were injected with $^{18}F-FDG$ over 30-s into peripheral vein while acquisition of the serial transaxial tomographic images were started. For acquisition protocol, we used twelve 10-s, four 30-s, sixteen 60-s, five 300-s and one 900-s frame for 60 mins. Its images were analyzed by visual interpretation TAC, SUV-DC and a kinetic analysis(Patlak analysis). The latter was based on region of interest(ROIs) which were drawn with the lung disease shape. Each optimized patterns were compared with itself. Results: In TAC patterns, it hard to observe cancer type with inflammation disease in early pool blood area but over the time cancer type slope more remarkably increased than inflammation disease. SUV-DC was similar to TAC pattern. In the result of Patlak analysis, In time activity curve of aorta, even though inflammation disease showed higher blood activity than cancer, at first as time went by, blood activity of inflammation disease became the lowest. However, in time activity curve of tissue, cancer had the highest uptake and inflammation disease was in the middle. Conclusion: Through the examination, TAC and SUV-DC could approached the results that lung cancer type and inflammation disease type has it's own difference shape patterns. Also, it has outstanding differentiation between cancer type and inflammation in Patlak and MRGlu analysis. Through these analysis methods, it will helpful to separation lung disease.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.1
• /
• pp.58-64
• /
• 2011

Objective: The 3-dimensional reconstruction method with resolution recovery modeling has advantages of high spatial resolution and contrast because of its precise modeling of spatial blurring according to the distance from detector plane. The aim of this study was to evaluate one of the resolution recovery reconstruction methods (Astonish, Philips Medical), compare it to other iterative reconstructions, and verify its clinical usefulness. Materials and Methods: NEMA IEC PET body phantom and Flanges Jaszczak ECT phantom (Data Spectrum Corp., USA) studies were performed using Skylight SPECT (Philips) system under four different conditions; short or long (2 times of short) radius, and half or full (40 kcts/frame) acquisition counts. Astonish reconstruction method was compared with two other iterative reconstructions; MLEM and 3D-OSEM which vendor supplied. For quantitative analysis, the contrast ratios obtained from IEC phantom test were compared. Reconstruction parameters were determined by optimization study using graph of contrast ratio versus background variability. The qualitative comparison was performed with Jaszczak ECT phantom and human myocardial data. Results: The overall contrast ratio was higher with Astonish than the others. For the largest hot sphere of 37 mm diameter, Astonish showed about 27.1% and 17.4% higher contrast ratio than MLEM and 3D-OSEM, in short radius study. For long radius, Astonish showed about 40.5% and 32.6% higher contrast ratio than MLEM and 3D-OSEM. The effect of acquired counts was insignificant. In the qualitative studies with Jaszczak phantom and human myocardial data, Astonish showed the best image quality. Conclusion: In this study, we have found out that Astonish can provide more reliable clinical results by better image quality compared to other iterative reconstruction methods. Although further clinical studies are required, Astonish would be used in clinics with confidence for enhancement of images.

• Economic and Environmental Geology
• /
• v.18 no.1
• /
• pp.65-92
• /
• 1985

A total of 12 mineral commodities significant in domestic output, economy and/or strategy of the Republic of Korea are chosen to examine the structural changes in production and demand-supply of these minerals during the last two decades of her industrialization. These include iron and manganese ores as the raw materials for iron and steel making, copper, zinc and tungsten ores among other non-ferrous metallic minerals, limestone (cement), kaolin, talc, pyrophyllite and graphite among other non-metallic minerals, and anthracite coal as the only domestic source of fossil energy. These are reviewed historically in time-series based on the statistical data which are tabulated and graphed in terms of domestic output, export, import, apparent demand-supply, its increasing rate, and self-sufficiency rate of each commodity. The increasing rates of demand-supply (IRDS) of some more important commodities are compared with those of Gross Domestic Production (GDP) and Economic Growth Rate (EGR) to evaluate how the IRDS contributed to the GDP and EGR. The major results revealed are as follows: Among the 12 commodities, the domestic output of 8 commodities appeared to have grown with steady upward trends: they are ores of lead, zinc and tungsten, limestone (cement), kaolin, talc, pyrophyllite and anthracite coal. Two commodities, ores of iron and copper, continued with unchanging or slightly declining trends and varied fluctuations, in spite of their cardinal importance to the heavy industry and strategy of Korea. The remaining two, graphite and manganese ore, have gradualy declined in domestic output in which the former has still enough resource potential but the latter has not and virtually ceased its domestic output. Trade patterns for mineral commodities in the Republic of Korea during the last two decades have changed greatly, being marked by a shift from mineral-exporting to mineral importing, mainly because of increasing consumption of mineral raw materials for industrialization rather than beceuse of decreasing output of domestic mineral commodities in quantity. In terms of trade patterns, the 12 commodities concerned in this study can be classified into the following four groups. The 1st group - ores of lead and tungsten have only been exported without imports. The 2nd group - amorphous graphite, and pyrophyllite have mainly been exported but partly been imported. The 3rd group - kaolin, talc and crystalline graphite have equally been exported and imported, but quantity of imports have rapidly been increased with time. The 4th group - ores of iron, manganese and zinc have shifted from exports to imports during the industrialization, particularly owing to the initiation of iron and steel making by the Pohang Iron and Steel Company in the middle 1970' s and the new establishment of the Onsan Zinc Refinery in the late 1970' s. All of the 12 commodities under considerations were far above 100% in self-sufficiency rate before or in the early 1960' s. Recently, however, most of them have been declined to below 100% except for those of limestone (cement) and pyrophyllite. It is particularly serious to identify that the self-sufficiency rates of the three important metallic minerals, iron, copper and manganese ores in 1982 appeared to be 5.1%, 0.5%, and 0.01%, respectively. The average self-sufficiency rate of the total domestic minerals produced in 1982 was 14.4% (in value) for that year. Mining industry appeared to be extremely high in its intermediate demand rate whereas its intermediate input rate to be quite low indicating that mineral raw materials have been exerted strong forward linkage effects upon the other industries rather than backward linkage effects. In comparing the curves of increasing rates of demand-supply of several major minerals - iron ore, manganese ore, copper ore, limestone (cement), kaolin, and anthracite coal - with those of Gross Domestic Production and Economic Growth Rate drawn on every graph, it is clearly shown that the curves of increasing rates of demand-supply comprise around 6 to 7 periods of cycles which roughly harmonious with those of the curves of GDP and EGR, except for the curve of anthracite coal of which the configuration seems to have resulted from the (artificial) government's mineral policy rather than from economic free market mechanism. The harmonic feature of these curves well suggests that the increasing rates of demand-supply of major minerals have been significantly contributed to the GDP and EGR. In addition, the wider amplitudes of the iron, manganese and copper curves than those of the limestone (cement) and kaolin curves indicate that the contribution of the former, metallic commodities, has been greater than that of the latter, non-metallic commodities.

• Journal of the Korean Society of Earth Science Education
• /
• v.10 no.1
• /
• pp.50-61
• /
• 2017

The purpose of this study is to analysis eye tracking for high school students' learning styles in the process of solving in the behavioral domains of the College Scholastic Ability Test on Earth Science I. The subjects of this study were 50 students from two classes out of 4 classes in E high school in Chungcheong province. Among them, we conducted experiments by randomly sampling 2 students of each type of learning based on the criteria that they had not encountered the problem of Earth Science I from the past two years. The findings indicate that the item correctness rate of divergers, assimilators, convergers, and accommodators were higher in the knowledge domain, application domain, knowledge-understanding domain, and understanding domain. This confirms that there is a difference among the four learning styles in the level of achievement according to the behavioral areas of the assessment questions. The latter finding was that the high eye-share of AOI 2 appeared higher than AOI 1, 3, 4 in the course of solving the problems. This is because the four types of learners pay more careful attention to the AOI 2 area, which is the cue-or-information area of problem solving, that is, the Table, Figure, and Graph area. Therefore, in order to secure the fairness and objectivity of the selection, it is necessary that an equal number of questions of each behavioral domain be selected on the Earth Science I Test of the College Scholastic Ability Test in general. Besides, it seems to be necessary that the knowledge, understanding, application, and the behavior area of the inquiry be highly correlated with the AOI 2 area in development of test questions.

• Journal of KIISE:Databases
• /
• v.33 no.1
• /
• pp.102-116
• /
• 2006

Electronic catalogs (or e-catalogs) hold information about the goods and services offered or requested by the participants, and consequently, form the basis of an e-commerce transaction. Catalog management is complicated by a number of factors and product classification is at the core of these issues. Classification hierarchy is used for spend analysis, custom3 regulation, and product identification. Classification is the foundation on which product databases are designed, and plays a central role in almost all aspects of management and use of product information. However, product classification has received little formal treatment in terms of underlying model, operations, and semantics. We believe that the lack of a logical model for classification Introduces a number of problems not only for the classification itself but also for the product database in general. It needs to meet diverse user views to support efficient and convenient use of product information. It needs to be changed and evolved very often without breaking consistency in the cases of introduction of new products, extinction of existing products, class reorganization, and class specialization. It also needs to be merged and mapped with other classification schemes without information loss when B2B transactions occur. For these requirements, a classification scheme should be so dynamic that it takes in them within right time and cost. The existing classification schemes widely used today such as UNSPSC and eClass, however, have a lot of limitations to meet these requirements for dynamic features of classification. In this paper, we try to understand what it means to classify products and present how best to represent classification schemes so as to capture the semantics behind the classifications and facilitate mappings between them. Product information implies a plenty of semantics such as class attributes like material, time, place, etc., and integrity constraints. In this paper, we analyze the dynamic features of product databases and the limitation of existing code based classification schemes. And describe the semantic classification model, which satisfies the requirements for dynamic features oi product databases. It provides a means to explicitly and formally express more semantics for product classes and organizes class relationships into a graph. We believe the model proposed in this paper satisfies the requirements and challenges that have been raised by previous works.

• Journal of Nutrition and Health
• /
• v.52 no.1
• /
• pp.36-46
• /
• 2019

Purpose: This study evaluated amounts of physical activity and sedentary behavior patterns in older adults using an accelerometer and physical activity diary. Methods: Forty-nine older adults (male 26, female 23) participated in this study. They wore a triaxial accelerometer (ActiGraph wGT3X-BT) for one week and wrote a physical activity diary concurrently for three days. Amounts of physical activity, sedentary behavior patterns, and percentage of meeting the World health organization (WHO) physical activity guidelines were analyzed using an accelerometer. In addition, the contents recorded in the physical activity diary were reclassified to 18 levels and the average daily times spent on each level and physical activity level (PAL) were calculated. Results: The subjects were sitting more than half of the day except for bedtime and shower time (59.2%). The numbers of prolonged ${\geq}30$, 40 minutes sedentary bouts were significantly higher in males ($3.10{\pm}1.34$, $1.78{\pm}1.09$, respectively) than in females ($2.34{\pm}1.22$, $1.32{\pm}1.07$, respectively) and the number of breaks per sedentary hour was significantly less in males ($5.74{\pm}0.89$) than in females ($6.44{\pm}0.71$). Among the activities corresponding to sedentary behavior surveyed by the physical activity diary, only the amount of time spent 'resting, speaking and watching TV' showed a significant correlation with the sedentary behavior pattern measured by the accelerometer. The persistence of sedentary behavior was interrupted primarily when low intensity activity was performed. Only 22.4% of the subjects met WHO physical activity guidelines. Conclusion: Based on these results, the physical activity guidelines for older adults should be developed that reflects the appropriate strength, including low activity level and maintenance time of moderate to vigorous physical activity.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.7 no.1
• /
• pp.861-876
• /
• 1965

During my stay in the Netherlands, I have studied the following, primarily in relation to the Mokpo Yong-san project which had been studied by the NEDECO for a feasibility report. 1. Unit hydrograph at Naju There are many ways to make unit hydrograph, but I want explain here to make unit hydrograph from the- actual run of curve at Naju. A discharge curve made from one rain storm depends on rainfall intensity per houre After finriing hydrograph every two hours, we will get two-hour unit hydrograph to devide each ordinate of the two-hour hydrograph by the rainfall intensity. I have used one storm from June 24 to June 26, 1963, recording a rainfall intensity of average 9. 4 mm per hour for 12 hours. If several rain gage stations had already been established in the catchment area. above Naju prior to this storm, I could have gathered accurate data on rainfall intensity throughout the catchment area. As it was, I used I the automatic rain gage record of the Mokpo I moteorological station to determine the rainfall lntensity. In order. to develop the unit ~Ydrograph at Naju, I subtracted the basic flow from the total runoff flow. I also tried to keed the difference between the calculated discharge amount and the measured discharge less than 1O~ The discharge period. of an unit graph depends on the length of the catchment area. 2. Determination of sluice dimension Acoording to principles of design presently used in our country, a one-day storm with a frequency of 20 years must be discharged in 8 hours. These design criteria are not adequate, and several dams have washed out in the past years. The design of the spillway and sluice dimensions must be based on the maximun peak discharge flowing into the reservoir to avoid crop and structure damages. The total flow into the reservoir is the summation of flow described by the Mokpo hydrograph, the basic flow from all the catchment areas and the rainfall on the reservoir area. To calculate the amount of water discharged through the sluiceCper half hour), the average head during that interval must be known. This can be calculated from the known water level outside the sluiceCdetermined by the tide) and from an estimated water level inside the reservoir at the end of each time interval. The total amount of water discharged through the sluice can be calculated from this average head, the time interval and the cross-sectional area of' the sluice. From the inflow into the .reservoir and the outflow through the sluice gates I calculated the change in the volume of water stored in the reservoir at half-hour intervals. From the stored volume of water and the known storage capacity of the reservoir, I was able to calculate the water level in the reservoir. The Calculated water level in the reservoir must be the same as the estimated water level. Mean stand tide will be adequate to use for determining the sluice dimension because spring tide is worse case and neap tide is best condition for the I result of the calculatio 3. Tidal computation for determination of the closure curve. During the construction of a dam, whether by building up of a succession of horizontael layers or by building in from both sides, the velocity of the water flowinii through the closing gapwill increase, because of the gradual decrease in the cross sectional area of the gap. 1 calculated the . velocities in the closing gap during flood and ebb for the first mentioned method of construction until the cross-sectional area has been reduced to about 25% of the original area, the change in tidal movement within the reservoir being negligible. Up to that point, the increase of the velocity is more or less hyperbolic. During the closing of the last 25 % of the gap, less water can flow out of the reservoir. This causes a rise of the mean water level of the reservoir. The difference in hydraulic head is then no longer negligible and must be taken into account. When, during the course of construction. the submerged weir become a free weir the critical flow occurs. The critical flow is that point, during either ebb or flood, at which the velocity reaches a maximum. When the dam is raised further. the velocity decreases because of the decrease\ulcorner in the height of the water above the weir. The calculation of the currents and velocities for a stage in the closure of the final gap is done in the following manner; Using an average tide with a neglible daily quantity, I estimated the water level on the pustream side of. the dam (inner water level). I determined the current through the gap for each hour by multiplying the storage area by the increment of the rise in water level. The velocity at a given moment can be determined from the calcalated current in m3/sec, and the cross-sectional area at that moment. At the same time from the difference between inner water level and tidal level (outer water level) the velocity can be calculated with the formula $h= \frac{V^2}{2g}$ and must be equal to the velocity detertnined from the current. If there is a difference in velocity, a new estimate of the inner water level must be made and entire procedure should be repeated. When the higher water level is equal to or more than 2/3 times the difference between the lower water level and the crest of the dam, we speak of a "free weir." The flow over the weir is then dependent upon the higher water level and not on the difference between high and low water levels. When the weir is "submerged", that is, the higher water level is less than 2/3 times the difference between the lower water and the crest of the dam, the difference between the high and low levels being decisive. The free weir normally occurs first during ebb, and is due to. the fact that mean level in the estuary is higher than the mean level of . the tide in building dams with barges the maximum velocity in the closing gap may not be more than 3m/sec. As the maximum velocities are higher than this limit we must use other construction methods in closing the gap. This can be done by dump-cars from each side or by using a cable way.e or by using a cable way.

• Journal of Intelligence and Information Systems
• /
• v.19 no.2
• /
• pp.1-20
• /
• 2013

Nowadays, social network is a huge communication platform for providing people to connect with one another and to bring users together to share common interests, experiences, and their daily activities. Users spend hours per day in maintaining personal information and interacting with other people via posting, commenting, messaging, games, social events, and applications. Due to the growth of user's distributed information in social network, there is a great potential to utilize the social data to enhance the quality of recommender system. There are some researches focusing on social network analysis that investigate how social network can be used in recommendation domain. Among these researches, we are interested in taking advantages of the interaction between a user and others in social network that can be determined and known as social relationship. Furthermore, mostly user's decisions before purchasing some products depend on suggestion of people who have either the same preferences or closer relationship. For this reason, we believe that user's relationship in social network can provide an effective way to increase the quality in prediction user's interests of recommender system. Therefore, social relationship between users encountered from social network is a common factor to improve the way of predicting user's preferences in the conventional approach. Recommender system is dramatically increasing in popularity and currently being used by many e-commerce sites such as Amazon.com, Last.fm, eBay.com, etc. Collaborative filtering (CF) method is one of the essential and powerful techniques in recommender system for suggesting the appropriate items to user by learning user's preferences. CF method focuses on user data and generates automatic prediction about user's interests by gathering information from users who share similar background and preferences. Specifically, the intension of CF method is to find users who have similar preferences and to suggest target user items that were mostly preferred by those nearest neighbor users. There are two basic units that need to be considered by CF method, the user and the item. Each user needs to provide his rating value on items i.e. movies, products, books, etc to indicate their interests on those items. In addition, CF uses the user-rating matrix to find a group of users who have similar rating with target user. Then, it predicts unknown rating value for items that target user has not rated. Currently, CF has been successfully implemented in both information filtering and e-commerce applications. However, it remains some important challenges such as cold start, data sparsity, and scalability reflected on quality and accuracy of prediction. In order to overcome these challenges, many researchers have proposed various kinds of CF method such as hybrid CF, trust-based CF, social network-based CF, etc. In the purpose of improving the recommendation performance and prediction accuracy of standard CF, in this paper we propose a method which integrates traditional CF technique with social relationship between users discovered from user's behavior in social network i.e. Facebook. We identify user's relationship from behavior of user such as posts and comments interacted with friends in Facebook. We believe that social relationship implicitly inferred from user's behavior can be likely applied to compensate the limitation of conventional approach. Therefore, we extract posts and comments of each user by using Facebook Graph API and calculate feature score among each term to obtain feature vector for computing similarity of user. Then, we combine the result with similarity value computed using traditional CF technique. Finally, our system provides a list of recommended items according to neighbor users who have the biggest total similarity value to the target user. In order to verify and evaluate our proposed method we have performed an experiment on data collected from our Movies Rating System. Prediction accuracy evaluation is conducted to demonstrate how much our algorithm gives the correctness of recommendation to user in terms of MAE. Then, the evaluation of performance is made to show the effectiveness of our method in terms of precision, recall, and F1-measure. Evaluation on coverage is also included in our experiment to see the ability of generating recommendation. The experimental results show that our proposed method outperform and more accurate in suggesting items to users with better performance. The effectiveness of user's behavior in social network particularly shows the significant improvement by up to 6% on recommendation accuracy. Moreover, experiment of recommendation performance shows that incorporating social relationship observed from user's behavior into CF is beneficial and useful to generate recommendation with 7% improvement of performance compared with benchmark methods. Finally, we confirm that interaction between users in social network is able to enhance the accuracy and give better recommendation in conventional approach.

• Journal of radiological science and technology
• /
• v.31 no.1
• /
• pp.17-23
• /
• 2008

Purpose : Because there is a difference depending on the environment as for an inspection equipment the important part of bone density scan and the precision/accuracy of a tester, the management of quality must be made systematically. The equipment failure caused by overload effect due to the aged equipment and the increase of a patient was made frequently. Thus, the replacement of equipment and additional purchases of new bonedensity equipment caused a compatibility problem in tracking patients. This study wants to know whether the clinical changes of patient's bonedensity can be accurately and precisely reflected when used it compatiblly like the existing equipment after equipment replacement and expansion. Materials and methods : Two equipments of GE Lunar Prodigy Advance(P1 and P2) and the Phantom HOLOGIC Spine Road(HSP) were used to measure equipment precision. Each device scans 20 times so that precision data was acquired from the phantom(Group 1). The precision of a tester was measured by shooting twice the same patient, every 15 members from each of the target equipment in 120 women(average age 48.78, 20-60 years old)(Group 2). In addition, the measurement of the precision of a tester and the cross-calibration data were made by scanning 20 times in each of the equipment using HSP, based on the data obtained from the management of quality using phantom(ASP) every morning (Group 3). The same patient was shot only once in one equipment alternately to make the measurement of the precision of a tester and the cross-calibration data in 120 women(average age 48.78, 20-60 years old)(Group 4). Results : It is steady equipment according to daily Q.C Data with $0.996\;g/cm^2$, change value(%CV) 0.08. The mean${\pm}$SD and a %CV price are ALP in Group 1(P1 : $1.064{\pm}0.002\;g/cm^2$, $%CV=0.190\;g/cm^2$, P2 : $1.061{\pm}0.003\;g/cm^2$, %CV=0.192). The mean${\pm}$SD and a %CV price are P1 : $1.187{\pm}0.002\;g/cm^2$, $%CV=0.164\;g/cm^2$, P2 : $1.198{\pm}0.002\;g/cm^2$, %CV=0.163 in Group 2. The average error${\pm}$2SD and %CV are P1 - (spine: $0.001{\pm}0.03\;g/cm^2$, %CV=0.94, Femur: $0.001{\pm}0.019\;g/cm^2$, %CV=0.96), P2 - (spine: $0.002{\pm}0.018\;g/cm^2$, %CV=0.55, Femur: $0.001{\pm}0.013\;g/cm^2$, %CV=0.48) in Group 3. The average error${\pm}2SD$, %CV, and r value was spine : $0.006{\pm}0.024\;g/cm^2$, %CV=0.86, r=0.995, Femur: $0{\pm}0.014\;g/cm^2$, %CV=0.54, r=0.998 in Group 4. Conclusion: Both LUNAR ASP CV% and HOLOGIC Spine Phantom are included in the normal range of error of ${\pm}2%$ defined in ISCD. BMD measurement keeps a relatively constant value, so showing excellent repeatability. The Phantom has homogeneous characteristics, but it has limitations to reflect the clinical part including variations in patient's body weight or body fat. As a result, it is believed that quality control using Phantom will be useful to check mis-calibration of the equipment used. A value measured a patient two times with one equipment, and that of double-crossed two equipment are all included within 2SD Value in the Bland - Altman Graph compared results of Group 3 with Group 4. The r value of 0.99 or higher in Linear regression analysis(Regression Analysis) indicated high precision and correlation. Therefore, it revealed that two compatible equipment did not affect in tracking the patients. Regular testing equipment and capabilities of a tester, then appropriate calibration will have to be achieved in order to calculate confidential BMD.

• Journal of Intelligence and Information Systems
• /
• v.19 no.1
• /
• pp.57-77
• /
• 2013

Social media has become one of the most popular media in web and mobile application. In 2011, social networks and blogs are still the top destination of online users, according to a study from Nielsen Company. In their studies, nearly 4 in 5active users visit social network and blog. Social Networks and Blogs sites rule Americans' Internet time, accounting to 23 percent of time spent online. Facebook is the main social network that the U.S internet users spend time more than the other social network services such as Yahoo, Google, AOL Media Network, Twitter, Linked In and so on. In recent trend, most of the companies promote their products in the Facebook by creating the "Facebook Page" that refers to specific product. The "Like" option allows user to subscribed and received updates their interested on from the page. The film makers which produce a lot of films around the world also take part to market and promote their films by exploiting the advantages of using the "Facebook Page". In addition, a great number of streaming service providers allows users to subscribe their service to watch and enjoy movies and TV program. They can instantly watch movies and TV program over the internet to PCs, Macs and TVs. Netflix alone as the world's leading subscription service have more than 30 million streaming members in the United States, Latin America, the United Kingdom and the Nordics. As the matter of facts, a million of movies and TV program with different of genres are offered to the subscriber. In contrast, users need spend a lot time to find the right movies which are related to their interest genre. Recent years there are many researchers who have been propose a method to improve prediction the rating or preference that would give the most related items such as books, music or movies to the garget user or the group of users that have the same interest in the particular items. One of the most popular methods to build recommendation system is traditional Collaborative Filtering (CF). The method compute the similarity of the target user and other users, which then are cluster in the same interest on items according which items that users have been rated. The method then predicts other items from the same group of users to recommend to a group of users. Moreover, There are many items that need to study for suggesting to users such as books, music, movies, news, videos and so on. However, in this paper we only focus on movie as item to recommend to users. In addition, there are many challenges for CF task. Firstly, the "sparsity problem"; it occurs when user information preference is not enough. The recommendation accuracies result is lower compared to the neighbor who composed with a large amount of ratings. The second problem is "cold-start problem"; it occurs whenever new users or items are added into the system, which each has norating or a few rating. For instance, no personalized predictions can be made for a new user without any ratings on the record. In this research we propose a clustering method according to the users' genre interest extracted from social network service (SNS) and user's movies rating information system to solve the "cold-start problem." Our proposed method will clusters the target user together with the other users by combining the user genre interest and the rating information. It is important to realize a huge amount of interesting and useful user's information from Facebook Graph, we can extract information from the "Facebook Page" which "Like" by them. Moreover, we use the Internet Movie Database(IMDb) as the main dataset. The IMDbis online databases that consist of a large amount of information related to movies, TV programs and including actors. This dataset not only used to provide movie information in our Movie Rating Systems, but also as resources to provide movie genre information which extracted from the "Facebook Page". Formerly, the user must login with their Facebook account to login to the Movie Rating System, at the same time our system will collect the genre interest from the "Facebook Page". We conduct many experiments with other methods to see how our method performs and we also compare to the other methods. First, we compared our proposed method in the case of the normal recommendation to see how our system improves the recommendation result. Then we experiment method in case of cold-start problem. Our experiment show that our method is outperform than the other methods. In these two cases of our experimentation, we see that our proposed method produces better result in case both cases.