• 한국결정성장학회지
• /
• 제22권4호
• /
• pp.178-182
• /
• 2012

결정립 성장은 여러 가지 재료의 성질에 미치는 큰 영향으로 재료공학에서 매우 중요하다. 그래서 본 연구에서는 PC에서 대규모 상장 모델을 사용하여 이방성 결정립 계면에너지의 2차원 결정립 성장에 미치는 효과를 조사하였다. 컴퓨터 모사에서는 $2000{\times}2000$의 그리드 시스템과 약 7300개의 초기 결정립 개수가 사용되었다. 결정립계 에너지의 이방성의 비, ${\sigma}_{max}/{\sigma}_{min}$는 1부터 3까지 변경되었다. 이방성이 증가함에 따라 결정립 성장 지수, n은 2.05에서 2.37로 증가하였다. 결정립 크기의 분포는 등방성인 경우에는 중앙에 평탄한 영역을 보였으나 이방성의 경우에는 중앙의 평탄한 영역이 사라지고 매우 느리게 사라지는 작은 결정립에 기인하여 작은 결정립 크기의 분포가 약간 증가하였다. 마지막으로 모사된 결정립 미세구조가 이방성에 따라 비교, 분석되었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.291-293
• /
• 1997

The effect of strain accumulation on the superplastic deformation behavior has been investigated through a series of load relaxation tests. The experimental results were analyzed using the recently proposed inelastic constitutive theory. The superplastic deformation of fine grained materials is confirmed to consist of grain boundary sliding and accommodating grain matrix deformation. However the flow behavior is changed with the plastic strain. It is believed that the microstructural changes such as grain growth and cavitation affect the superplastic deformation behaviors.

• 한국세라믹학회지
• /
• 제47권1호
• /
• pp.71-74
• /
• 2010

We have investigated protonic conduction in highly dense (>98%) polycrystalline Y-doepd $BaZrO_3$ (BYZ) ceramic with an average grain size of ~85 nm. It is observed that the protonic conductivity across the grain boundaries in this nano-crystallilne BYZ (n-BYZ) is significantly higher than the microcrystalline counterpart. Such a remarkable enhancement in grain boundary conductivity results in high overall conductivity that may allow this chemically stable protonic conductor to serve as a solid electrolyte for low-temperature solid oxide fuel cell applications.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.326-331
• /
• 2007

Large-scale molecular dynamics simulations are performed to verify the deformation characteristics of grain boundaries in nanolithography process. The copper substrate made of 200,000 atoms is constructed by two grains in different crystal orientations using dynamic relaxation method. The grain boundary is located in the middle of the substrate with $45\sim135$ degree angles. The plowing tip is made of diamond-like-carbon atoms in a variety of shapes. In the simulations, the generation, propagation, and accumulation of dislocations are observed inside the substrate. From the numerical results, we address the dynamic behavior of the grain boundaries as well as the frictional characteristics in terms of the morphology of initial grain boundaries.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1738-1740
• /
• 1999

This paper deals with a novel structure of poly-Si solar cell. A solar cell conversion efficiency was degraded by grain boundary effect in Polycrystalline silicon. To reduce grain boundary effect, we performed a preferential grain boundary etching, $POCl_3$ n-type emitter doping, and then ITO film growth on poly-Si. Among the various preferential etchants, Schimmel etch solution exhibited the best result having grain boundary etch depth about $10{\mu}m$. RF magnetron sputter grown ITO films showed a low resistivity of $10^{-4}\Omega-cm$ and high transmittance of 85%. With well fabricated poly-Si solar cells. we were able to achieve as high as 15% conversion efficiency at the input power of 20mW/$cm^2$.

• 한국정밀공학회지
• /
• 제25권4호
• /
• pp.127-133
• /
• 2008

As the application of the MEMS parts increases, the structural safety of MEMS appears importantly. A lot of MEMS parts are made by a multi-grain silicon wafer, which is an orthotropic material. Moreover directions of the materials on each grain are distributed randomly. The stress analysis for the multi-grain is important factor in order to apply the MEMS parts to industrial applications. The finite element method (FEM) is commonly used by a stress analysis method but the boundary element method (BEM) is known as the result of the BEM is more accurate than that of the FEM since the fundamental solution are used. In this study, we derived the boundary integration equation for the orthotropic material by applying fundamental solutions with complex variables. The multi-region analysis procedure for the BEM and the multi-grain generation procedure by a random process technique are developed in order to apply the analysis of the multi-grain orthotropic material. The discontinuous element is used in order to remove the comer problem in the BEM. The results of the present method are compared with those of the finite element method in order to verify the present procedure.

• 대한기계학회논문집
• /
• 제4권4호
• /
• pp.152-159
• /
• 1980

The temperature and the grain boundary precipitation have the great influence on the low-cycle fatigue behavior of austenite stainless steel at elevated temperature. For the purpose of investigating the mechanism concerning the change of fatigue micro crack mode in SUS 316 under various conditions low-cycle fatigue test was carried out at the elevated temperature 600.deg.C, plastic strain range 2% and constant strain rate .5c.p.m. A special attention is given to the observation of intergranular crack initiation. The results obtained are summarized as follows. The low-cycle fatigue behavior of SUS 316 at 600.deg.C is affected by transition of crack initiation mode from intergranular to transgranular. The transition is due to the aging effect, which is caused by grain boundary precipitations of Cr$\_$23/C$\_$6/. Since the intergranular crack initiation is brought about by the grain boundary sliding, the transgranular crack initiates in case that the strengthening of grain boundary due to the precipitation of Cr$\_$23/C$\_$6/ carbides takes place ahead of the intergranular crack initiation.

• Nuclear Engineering and Technology
• /
• 제52권1호
• /
• pp.148-154
• /
• 2020

The radiation induced segregation of Cr at grain boundaries (GBs) in Ferritic/Martensitic steels was modeled assuming vacancy and interstitialcy diffusion mechanisms. In particular, the dependence of segregation on temperature and grain boundary misorientation angle was analyzed. It is found that Cr enriches at grain boundaries at low temperatures primarily through the interstitialcy mechanism while depletes at high temperatures predominantly through the vacancy mechanism. There is a crossover from Cr enrichment to depletion at an intermediate temperature where the Cr:Fe vacancy and interstitialcy diffusion coefficient ratios intersect. The bell-shape Cr enrichment response is attributed to the decreasing void sinks inside the grains as temperature rises. It is also shown that low angle grain boundaries (LAGBs) and special Σ coincidence-site lattice (CSL) grain boundaries exhibit suppressed radiation induced segregation (RIS) response while high angle grain boundaries (HAGBs) have high RIS segregation. This different behavior is attributed to the variations in dislocation density at different grain boundaries.

• Corrosion Science and Technology
• /
• 제12권6호
• /
• pp.265-273
• /
• 2013

Ti-stabilized 11 wt% Cr ferritic stainless steels (FSSs) for automotive exhaust systems have been experienced intergranular corrosion (IC) in some heat-affected zone (HAZ). The effects of sensitizing heat-treatment and silicon on IC were studied. Time-Temperature-Sensitization (TTS) curves showed that sensitization to IC was observed at the steels heat-treated at the temperature lower than $650^{\circ}C$ and that silicon improved IC resistance. The sensitization was explained by chromium depletion theory, where chromium is depleted by precipitation of chromium carbide during sensitizing heat-treatment. It was confirmed with the results from the analysis of precipitates as well as the thermodynamical prediction of stable phases. In addition, the role of silicon on IC was explained with the stabilization of grain boundary. In other words, silicon promoted the formation of the grain boundaries with low energy where precipitation was suppressed and consequently, the formation of Cr-depleted zone was retarded. The effect of silicon on the formation of grain boundaries with low energy was proved by the analysis of coincidence site lattice (CSL) grain boundary, which is a typical grain boundary with low energy.

• 대한금속재료학회지
• /
• 제49권12호
• /
• pp.924-929
• /
• 2011

It is well known that grain boundary cavitation is the main failure mechanism in austenitic stainless steel under tensile hold creep-fatigue interaction conditions. The cavities are nucleated at the grain boundary during cyclic loading and grow to become grain boundary cracks. The attenuation of ultrasound depends on scattering and absorption in polycrystalline materials. Scattering occurs when a propagation wave encounters microstructural discontinuities, such as internal voids or cavities. Since the density of the creep-fatigue cavities increases with the fatigue cycles, the attenuation of ultrasound will also be increased with the fatigue cycles and this attenuation can be detected nondestructively. In this study, it is found that individual grain boundary cavities are formed and grow up to about 100 cycles and then, these cavities coalesce to become cracks. The measured ultrasonic attenuation increased with the cycles up to cycle 100, where it reached a maximum value and then decreased with further cycles. These experimental measurements strongly indicate that the open pores of cavities contribute to the attenuation of ultrasonic waves. However, when the cavities develop, at the grain boundary cracks whose crack surfaces are in contact with each other, there is no longer any open space and the ultrasonic wave may propagate across the cracks. Therefore, the attenuation of ultrasonic waves will be decreased. This phenomenon of maximum attenuation is very important to judge the stage of grain boundary crack development, which is the indication of the dangerous stage of the structures.