• Resources Recycling
• /
• v.9 no.2
• /
• pp.40-45
• /
• 2000

Low density ceramic supporter was prepared by using fly ash as a starting mterial with borax or glass powders. Also the wheat powders were used by 30 wt% to increase the initial porosity of the supporter. The density of the supporter decreased as the amount of borax increased. The bulk density of $0.79g/\textrm{cm}^3$ and the apparent density of $1.10g/\textrm{cm}^3$ were obtained when the fly ash with 15% of borax was sintered at $1160^{\circ}C$ for 15 minutes. The density also decreased as the plate glass powders past through $212\mu\textrm{m}$ size were mixed. When the fly ash with 12% of glass powder was sintered at $1280^{\circ}C$ for 10 minutes, the bulk and apparent density were $0.90g/\textrm{cm}^3$ and $1.00g/\textrm{cm}^3$, respectively.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.11 no.1
• /
• pp.46-49
• /
• 2008

Recycling glass fiber, 'F-fiber,' was obtained by the separation of the roving layer from waste FRP and the concrete products or structures were considered for its application. Experiment was carried out for the bending strength of aggregate (2.45 of cement) by weight and F-fiber (density of 1.45, volume ratio to all of the aggregate and the cement). Whereas the specimen containing 1% F-fiber showed the bending strength 23% higher than that without F-fiber after curing far 28 days, the one with 0.5% F-fiber did not give any change. It could be found, therefore, that the minimum mixing amount should be larger than 0.5% fur the strength reinforcement. One of the reinforcing concrete product, bench flume, containing 1% F-fiber showed 21% increment of bending strength In contrast to that without F-fiber.

• Journal of the Korea Concrete Institute
• /
• v.13 no.2
• /
• pp.184-191
• /
• 2001

Recently, as industrialization is rapidly growing and the standard of life is rising, the quantities of waste glasses have been hastily increased and most of them are not recycled but abandoned. It cause some problems such as the waste of natural resources and environmental pollution. Therefore, this study was conducted basic experimental research to analyze the possibilities of recycling of waste glasses(crushed waste glasses outbreaking from our country such as amber, emerald-green, flint and mixed) as fine aggregates for concrete. Test results of fresh concrete, slump and compacting factors decrease because grain shape is angular and air content increase due to involving small size particles so much in waste glasses. Also compressive, tensile and flexural strengths decrease with increase of the content of waste glasses. In conclusion, the content of waste glasses below 30% is reasonable and usage of pertinent admixture is necessary to obtain workability and air content.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.1
• /
• pp.43-46
• /
• 2010

As one of the methods for recycling the FRP used for the small and medium-sized waste ships, separation of the roving layer from the mat has some merit in a sense of the recycling energy and the environmental effects. Similar characteristics between the roving and the mat make the mechanically automatic differentiation difficult. They, however, contain different ratio of the resin and the glass and the thickness. In this study photo physical differentiation between the two layers has been made using (1) boiling concentrated sulfuric acid which can dissolve the resin in the FRP layer and (2) hydrogen fluoride(HF) solution which can reacts with $SiO_2$ fragments of the glass. Furthermore coloring the FRP sample with water-soluble dye following the HF treatment makes the roving layer more distinguishable photophysically. The implementation of HF treatment has been successfully tested in this study.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.1
• /
• pp.50-57
• /
• 2021

In this study, the engineering charateristics of recycled cold asphalt mixtures using waste glass and red mud were examined as part of the development of low carbon road pavement materials using large amounts of waste. It also examined the satisfaction of the performance criteria specified in the standard. As a result of the study, it was found that RCA using waste glass were not met standard of GR since strain resistance reduced. Therefore, it has been shown that improvements in the composition of the mixture are needed. It has also been shown to significantly improve the performance of the mixture when adding red mud. In addition, it was found that the quality standards for stability, flow value, indirect tensile strength and tensile strength ratio as specified by GR are satisfied.

• Resources Recycling
• /
• v.30 no.1
• /
• pp.53-59
• /
• 2021

Waste vinyl generated from household waste has been used as a solid refuse fuel (SRF) due to the presence of impurities such as soil, metal, and glass; however, the amount of SRF used has been decreasing owing to recent environmental problems, thereby necessitating the need for recycling. In this study, the mixed recycled raw material produced from household waste vinyl and polyethylene (PE) single recycled raw material produced from agricultural waste vinyl were examined. Raw material analysis revealed that waste vinyl was mainly composed of polyethylene, and approximately 2% of ash remained in the mixed recycled raw material, whereas no ash was found in the PE single recycled raw material. In addition, the analysis of tensile strength according to the mixing ratio of the two recycled raw materials revealed that the highest tensile strength was approximately 16 MPa under the heat treatment temperature of 200 ℃, compression pressure of 30 MPa, and a mixing ratio of 3:7 (mixed:PE single). In addition, the highest bending strength was approximately 39 MPa under the heat treatment temperature of 200 ℃, compression pressure of 30 MPa, and a mixing ratio of 3:7 (mixed:PE single). Therefore, the possibility of recycling waste vinyl was suggested by investigating the change in strength characteristics according to the mixing ratio of the recycled raw materials.

• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.183-187
• /
• 2001

Present states on reutilization of metal-bearing solid wastes in China including metal-containing gangue, red mud, nonferrous metallurgical slag or residue, arsenical slag, steel - iron slag, waste batteries, were described in detail. The wastes pile up at a large quantity, resulting in seriously potential harm to environment. Most of these wastes, however, contain valuable metals, which are regarded as important secondary resources for extracting metals. Waste slag and batteries with a high grade of metals are treated by a hydro-based and / or pyre-based method for extracting valuable metals. While gangue and waste slag with a low grade are as a raw material in architecture field. In the future, a novel technology, such as high-grads magnetization separation technique and biological technique, will be designed to treat these wastes for protecting environment and recycling valuable components. These wastes, furthermore, are synthetically reutilized to produce various architectural materials, including glass and ceramics.

• Geomechanics and Engineering
• /
• v.6 no.3
• /
• pp.235-248
• /
• 2014

Population increase and economic developments can lead to construction as well as demolition of infrastructures such as buildings, bridges, roads, etc resulting in used concrete as a primary waste product. Recycling of waste concrete to obtain the recycled concrete aggregates (RCA) for base and/or sub-base materials in road construction is a foremost application to be promoted to gain economical and sustainability benefits. As the mortar, bricks, glass and reclaimed asphalt pavement (RAP) present as constituents in RCA, it exhibits inconsistent properties and performance. In this study, six different types of RCA samples were subjected classification tests such as particle size distribution, plasticity, compaction test, unconfined compressive strength (UCS) and California bearing ratio (CBR) tests. Results were compared with those of the standard road materials used in Queensland, Australia. It was found that material type 'RM1-100/RM3-0' and 'RM1-80/RM3-20' samples are in the margin of the minimum required specifications of base materials used for high volume unbound granular roads while others are lower than that the minimum requirement.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.2
• /
• pp.102-106
• /
• 2007

While the effort has been made in recycling the FRP (Fiber Reinforced Plastic) used for the medium-to-small size ships, researchers try to find out the methods more favorable for the environments and more value-added. In respect to the fact that the FRP consists of two types of layers, roving and mat, differentiated by the 2-dimensional structure, our group was able to separate the layers of FRP instead of grinding it. The roving cloth was cut to the long glass fibers (about 50 mm long; calling it 'F-fiber' afterwards). F-fiber showed increasing tensile strength and chemical-resistance possibly due to the remained resin (about 25% by weight). In this experiment fiber-reinforced mortars are made of the F-fiber as a recycling method of FRP. The mortar containing 2% (v/v) F-fiber results in 34.6% increment of bending strength from the standard after 28 day curing. The resulting strength is similar to that of the mortar with imported polyvinyl fiber P-54. These results imply that F-fiber can be applied to the 'fiber reinforced mortar' and furthermore may be a substitute for the imported fibers.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.15 no.1
• /
• pp.47-53
• /
• 2012

As one of the methods for recycling the FRP from the waste ships, separation of roving layer from the mat has some merits in a sense of the eco-friendly and economical recycling process. Similar characteristics, however, between the roving and the mat even with different ratio of the resin and the glass and the thickness of the roving, much thinner than the mat, make the mechanically automatic differentiation difficult. In this study spectrochemical differentiation between the two layers has been made using boiling concentrated sulfuric acid, methanol and isopropanol solution saturated with KOH, or hydrogen fluoride (HF) solution. Furthermore efficiently coloring water-soluble dye following the HF treatment makes the roving layer more distinguishable photophysically. The layer differentiation and the automatic layer distraction move up the date of simple and automatic separation process for the waste FRP.