• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.11a
• /
• pp.139-140
• /
• 2023

This study aims to determine the microstructural characteristics of waste glass beads, a lightweight aggregate manufactured from waste glass powder, when incorporated into mortar in order to examine its usability depending on the particle shape.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.1
• /
• pp.229-236
• /
• 2003

Ultrasonic propagation velocities of both the dilatational and shear waves through the weathered tuff soil sampled from the area tying between Ulanbator and Beijing were measured under temperature condition of near subzero by means of sing-around method. After comparing the results with obtained data on unfrozen water content, a linear relation between velocities and unfrozen water content was performed with high coefficient value. Experimental results of two kinds of rather uniform materials, namely, glass-beads and silica micro-beads, testified the similar linear relations. In addition, the change rate of dilatational wave velocities with the change of volumetric unfrozen water content was not dependent on soil type. Although a rational theory of the ultrasonic velocities dependence on the unfrozen water content is not yet proposed, the presented empirical relationships may suggest the appropriate evaluation to the effect of unfrozen water on dynamic characteristics of frozen soil.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.4
• /
• pp.825-832
• /
• 1988

An experiment was performed to study the heat pipe phenomenon of porous media heated above at one-dimensional steady state for the range of heat flux, 300 W/ $m^{2}$ ~ 2000w/ $m^{2}$. Glass beads, sand, and copper particles were used as porous media and distilled water was used as a working fluid. Result of experiment shows that the length of the two-phase zone increases with the decreasing particle size for the same heat flux. At relatively lower heat flux the length of the two-phase zone increases with the increasing heat flux, which contradicts the result of earlier work. However, its length remains nearly constant when the heat flux increases above a certain value. The length of the two-phase zone is proportional to the product of the heat flux by the hydrostatic capillary height under the limited value on heat flux, that is, $l_{t}$ = A(q. $l_{cap}$)+B, q.leg.1/A(C+B/ $l_{cap}$) where A is 1.7*10$^{-4}$ $m^{2}$/w, B is 1.9*10$^{-2}$ m, and C is 0.43 for copper particles and 0.31 for glass beads and sand.d.d.d.

• Journal of Industrial Technology
• /
• v.30 no.A
• /
• pp.127-132
• /
• 2010

We analyzed the effects of several process variables on the $SO_2$ removal and particle growth by the dielectric barrier discharge - photocatalysts hybrid process. In this process, $SO_2$ was converted into the ammonium sulfate ($(NH_4)_2SO_4$) particles. The size and crystallinity of ammonium sulfate particles were examined by using TEM and XRD analysis. The dielectric barrier discharge reactor consisted of two zones: the first is for plasma generation and the second is for ammonium sulfate particles formation and growth. The first zone of reactor was filled with glass beads as a dielectric material. To enhance $SO_2$ removal process, the $TiO_2$ photocatalysts were coated on glass beads by dip-coating method. As the voltage applied to the plasma reactor or the pulse frequency of applied voltage increases, the $SO_2$ removal efficiency increases. Also as the initial concentration of $SO_2$ decreases or as the residence time increases, the $SO_2$ removal efficiency increases. $(NH_4)_2SO_4$ particles continue to grow by particle coagulation and surface reaction, moving inside the reactor. Larger particles in site are produced according to the increase of residence time or $SO_2$ concentrations.

• Clean Technology
• /
• v.17 no.3
• /
• pp.209-214
• /
• 2011

The effects of inlet gas velocity (0.26-0.31 m/s), inlet gas temperature (315-353 K) and the mass ratio (0.1-0.4) of fine polymer (crosslinked poly methyl methacrylate beads) to inert medium particles on the drying rate of fine polymer in a 0.15 m-ID ${\times}$ 1.0 m-high inert medium fluidized bed dryer have been investigated. Crosslinked PMMA beads of 20 ${\mu}m$ (group C) were used as fine polymer, and glass beads of 590 ${\mu}m$ (group B) were used as the inert medium. The drying rate increases with increasing inlet gas temperature and velocity. However, the drying rate decreases slightly as the mass ratio of fine polymer to inert medium particles increases. The particle size distribution of dried fine polymers was mono distribution.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.131-140
• /
• 2012

Lane markings such as edgelines, centerlines, and lines that delineate lanes generally provide drivers with the various information for safe driving. Drivers can easily recognize the lane markings through the color differences between the markings and road surfaces during the daytime. However, it is a bit difficult for drivers to perceive them during the nighttime due to the lack of artificial lights. Although the glass beads with the 1.5-refractive index have been used to improve the visibility of the lane markings during the nighttime, it is still difficult for drivers to recognize the lane markings properly, especially during the rainy nighttime, which may often lead to traffic accidents. To improve the retroreflectivity and visibility of the lane markings during the rainy nighttime, the high refractive beads with the 2.4-refractive index are essentially required, but they do not work appropriately during the dry nighttime. Thus, the mixed materials with the 1.5, 1.9, and 2.4-refractive beads should be considered for the satisfactory implementation of the lane markings. This study reveals the best mixing rates of the beads by conducting benefit-cost analysis under various weather conditions in Korea. The analysis results show that the lane markings with the 100% of the 2.4-refractive beads provide the highest visibility of lane markings regardless of the roadway conditions, but the benefit-cost (B/C) ratio of the bead mixture is merely 0.46. The best mixing rate of the beads, from the highest B/C ratio viewpoint, was identified as the mixture with a 80% of 1.5-refractive beads and a 20% of 2.4-refractive beads. Some limitations and future research agenda have also been discussed.

• Korean Chemical Engineering Research
• /
• v.44 no.3
• /
• pp.300-306
• /
• 2006

Photocatalyst deposited beads were prepared by fluidized bed chemical vapor deposition (FB-CVD) under various operating conditions of substrates, bed temperature, pressure, and oxygen concentration. Photocatalytic degradation of acetaldehyde was carried out to determine the optimum operating condition of prepared photocatalysts. They were characterized by using FE-SEM, XRD, and XPS. From the FE-SEM photographs, it was found that the surfaces of titania-coated beads were covered with crystal form, particle form, and slick form of titania on alumina, silica-gel, and glass beads, respectively. From the result of photocatalytic degradation of acetaldehyde, it was found that prepared titania/ alumina beads at $600^{\circ}C$, 5 torr showed superior performance to others, and oxygen flow rate has no significant effect.

• Applied Biological Chemistry
• /
• v.32 no.4
• /
• pp.374-377
• /
• 1989

To optimize the enzymatic saccharification of raw-starch, reaction conditions by shaking with glass beads were adapted together with ${\alpha}-amylase$ from Streptomyces sp. 4M-2 and amyloglucosidase from commercial source. When raw-starch was degraded by the ${\alpha}-amylase$ in shaking flask with beads (raw-starch : bead in diam. of 3mm=1 : 5 by weight) at the shaker speed of 300rpm, the saccharification rate of corn and potato starch were increased up to 88% and 69% after 30 hrs of reaction, respectively. Application of the amyloglucosidase in combination with the ${\alpha}-amylase$ enhanced the rate of saccharifcation: 88% of saccharification was obtained in 6 hrs for raw-corn starch under the same reaction conditions as above.

• Elastomers and Composites
• /
• v.56 no.2
• /
• pp.85-91
• /
• 2021

In this study, different types and shapes of various particles produced on the asphalt pavement road were analyzed. Road dust at a bus stop was collected and was separated as per their sizes by using a sieve shaker. Tire-road wear particles (TRWPs), asphalt pavement wear particles (APWPs), mineral particles, plant-related particles, glass beads, glass particles, road paint wear particles, plastic particles, and fibers were observed herein. The types and shapes of the particles varied depending on their sizes. TRWPs larger than 500 ㎛ were not observed. TRWPs with a size of 212-500 ㎛ were rarely present, but many TRWPs with a size smaller than 212 ㎛ were observed. APWPs were observed for whole-particle sizes of below 1,000 ㎛. A variety of particles on the road would lead to lower friction between the tires and the road, thereby increasing the braking distance of vehicles. Most of the particles include mineral particles, glass particles, and APWPs with rough surfaces. Therefore, the abrasion of the tire tread would accelerate owing to friction with the tough particles.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.12-17
• /
• 2002

The extracellular invertase (EC 3.2.1.26) (Candida utilis) preparation was obtained from the liquid medium after desalting and freeze drying. This prepared enzyme was used for the comparative purification on 4 activated matrices by liquid column affinity chromatography method. In this method there were used controlled porous glass (CPG) silanized covalently activated by keratin, silanized silica gel and silica gel covalently covered by keratin. It was found that the invertase purification process was better using both CPG matrices (silanized CPG and keratin activated CPG) than these with two silica gel supports. Also the elution coefficient of the invertase from the two CPG columns was about 93 to 94%. Two silica gel supports found to be superior in terms of purification efficiency. The invertase purification process was confirmed by PAGE electrophoresis.