• The Journal of the Korea Contents Association
• /
• v.19 no.5
• /
• pp.624-631
• /
• 2019

The purpose of this study was to observe the influence of adhesive force of lifter on powdered fingermark. First, an experiment was conducted to measure the adhesive force of five kinds of lifters. Second, each fingermark deposited on slide glass was developed using four kinds of powders. Then, these were transferred to lifter, and the quality of the transferred fingermark was observed. As a result of measuring the adhesive force of the lifter using the ASTM D3121-17 rolling ball tack method, the difference in adhesion between the lifters except the gelatin lifter was small. Also, it was confirmed that the quality of the transferred fingermark was not significantly related to the adhesive force of the lifter. However, if the quality of the transferred fingermark is not good when transferring to a gelatin lifter which is a lifter having a weak adhesive force, additional transfer is possible.

• Resources Recycling
• /
• v.29 no.2
• /
• pp.28-36
• /
• 2020

To enhance the recycling rate of wasted glass bottles toward recycled aggregates, the study would decide optimal comminution equipment based on the particle size distribution, aspect ratio and equipment energy analysis. The impact, compress and abrasion is type of generated force by comminution. So, hammer crusher, shredder, roll crusher and ball mill have been selected because they have characteristic which is each type of force. As a result of the particle size analysis of each product, only the shredder product satisfied concrete and asphalt aggregate quality standard condition. Also, as a result of aspect ratio analysis using Imaging software program (Image J, National institute of health), most of size fraction is confirmed under 1.6 value. It was confirmed that the product has low dangerousness and satisfying to shpage index. Also, the particle reduction ratio against input energy of shredder product was the most high. Therefore, we can decide that the optimal equipment which applicable for comminuting waste glass bottle in certain particle size under 10mm is shredder. The result of study will make contribution to increasing energy efficiency of comminution processing and competitiveness of product.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.191-191
• /
• 2008

강유전성 세라믹스 재료로써는 PZT계열의 세라믹재료가 널리 쓰이고 있다. 이는 우수한 유전 및 압전특성을 가지고 있으나, PbO을 다량 함유하고 있어 $1000^{\circ}C$이상에서 PbO가 급격하게 휘발되는 성질 때문에 조성의 변동이 생겨 재현성이 어려우며 이를 방지하기 위하여 PbO를 과잉 첨가시키기 때문에 PbO휘발로 인한 강한 독성이 인체에 유해하고, 비환경 친화적인 물질로 최근에는 환경문제가 대두됨에 따라 대체 또는 보완 할 수 있는 방안에 검토되고 있다. 본 연구는 그 해결책의 한 방안으로 압전특성이 우수한 $(Pb_{0.94}Sr_{0.06})[(Ni_{1/2}W_{1/2})_{0.02}(Mn_{1/3}Nb_{2/3})_{0.07}(Zr_{0.51}Ti_{0.49})_{0.91}]O_3$계 조성을 설계하고 Glass frit(0~1.1 wt%)를 소량 첨가하여 액상 소결 특성을 부여하고 $1000^{\circ}C$ 이하의 저온에서 소결하여 유전 및 압전 특성을 평가하였다. 실험방법은 일반적인 세라믹스 제조공정으로 24시간 ball milling하고 $850^{\circ}C$에서 2시간 하소 후 Glass frit를 소결조제로 소랑 첨가하여 $1000^{\circ}C$ 이하 온도에서 소결을 진행하여 각 소결온도에 따른 유전 및 압전 특성을 평가하였다. 최종 소결된 시편의 밀도와 수축율을 분석하여 최적의 소결온도를 확립하였으며 XRD분석을 통해 perovskite구조를 확인하고 미세구조확인을 위해 SEM으로 관찰하였다. 압전 특성을 평가하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.3
• /
• pp.56-63
• /
• 2003

A silent type ozone generator using water surface has been studied and improved its ozone generation characteristics by installing dielectric heads in the just under the surface of the wale- At this time, different permittivitis of dielectric beads were used to change the discharge condition of water surface. The current-voltage characteristics and characteristics of ozone generation quantity of the test system were investigated and discharge photos of glass beads were observed The height of Taylor cone may be the cause of the discharge bridge to decrease the ozone generation on the discharge spacing. In this study, the hight of Taylor cone could be controlled greatly by installing dielectric beads just under the water surface. Therefore a higher ozone generation also could be obtained. As the permittivity of dielectric material increased. discharge starting voltage was advanced and maximum 110 ppmy of ozone was generated by using the ferroelectric ball.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.5
• /
• pp.255-264
• /
• 2013

Cobalt aluminate ($CoAl_2O_4$) is a highly stable pigment with excellent resistance to light, weather, etc., which has resulted in widespread use as a ceramic pigment. Due to the unique optical characteristics, $CoAl_2O_4$ is generally used as a coloring agent to decorate porcelain products, glass, paints and plastics. Here, $CoAl_2O_4$ pigments were synthesized by polymerized complex method and solid state reaction. Then $CoAl_2O_4$ pigment were grinded using the attrition milling with 1 mm size zirconia ball for 3 hours. The attrition milling process was performed at the constant speed of 800 rpm and ball to powder weight ratio (BPR) was 100 : 1. The characteristics of synthesized pigment were analyzed by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), particle size analyser (PSA) and CIE $L^*a^*b^*$. The XRD patterns of $CoAl_2O_4$ show single phase spinel structure. The particle size of $CoAl_2O_4$ measured by FE-SEM, TEM and PSA analysis was in the range of 100~200 nm. The blue color of obtained $CoAl_2O_4$ pigments could be confirmed through CIE $L^*a^*b^*$ measurement.

• Journal of Mechanical Science and Technology
• /
• v.17 no.11
• /
• pp.1704-1713
• /
• 2003

Point contact film thickness in elastohydrodynamic lubrication (EHL) is analyzed by image processing method for the images from an optical interferometer with monochromatic incident light. Interference between the reflected lights both on half mirror Cr coating of glass disk and on super finished ball makes circular fringes depending on the contact conditions such as sliding velocity, applied load, viscosity-pressure characteristics and viscosity of lubricant under ambient pressure. In this situation the film thickness is regarded as the difference of optical paths between those reflected lights, which make dark and bright fringes with monochromatic incident light. The film thickness is computed by numbering the dark and bright fringe orders and the intensity (gray scale image) in each fringe regime is mapped to the corresponding film thickness. In this work, we developed a measuring technique for EHL film thickness by dividing the image patterns into two typical types under the condition of monochromatic incident light. During the image processing, the captured image is converted into digitally formatted data over the contact area without any loss of the image information of interferogram and it is also interpreted with consistency regardless of the observer's experimental experience. It is expected that the developed image processing method will provide a valuable basis to develop the image processing technique for color fringes, which is generally used for the measurement of relatively thin films in higher resolution.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.130-133
• /
• 2009

$Cu_2ZnSnSe_4$(CZTSe) is one of the promising materials for the solar cell due to its abundant availability in the nature. In this study, we report the fabrication of CZTSe thin film by Pulsed Laser Deposition(PLD) method using quaternary compound target on sodalime glass substrate. The quaternary CZTSe compound target was synthesized by solid state reaction method using elemental powders of Cu, Zn, Sn and Se. Powders were milled in high purity ethanol using zirconia ball with mixed size of 1 and 3 mm at the same proportions for 72 hours milling time. The structural, chemical and mechanical properties of the synthesized CZTSe powders were investigated prior to the deposition process. The CZTSe compound powder, and $500^{\circ}C$ of sintering temperature shows the best properties for PLD target. Results show that the as-deposited CZTSe thin films with the precursors by PLD have a composition near-stoichiometric.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.4
• /
• pp.139-143
• /
• 2005

For application of carbon nano-tube (CNT) as a counter electrode materials of dye-sensitized solar cell (DSSC), the electrochemical behavior of CNT electrode was studied, employing cyclic-voltammetry (C-V) and impedance spectroscopy. Fabrication of CNT-paste and formation of CNT-counter electrode for characteristic measurement have been carried out using ball-milling and doctor blade process, respectively. Unit cell for measurements was assembled using Pt electrode, CNT electrode, and iodine-embedded electrolyte. Field emission-scanning electron microscopy (FE-SEM) was used for structural investigation of CNT powder and electrode. Sheet resistance of electrode was measured with 4-point probe method. Electrochemical properties of electrode, C-V and impedance spectrum, were studied, employing potentiogalvanostat (EG&G 273A) and lock in amplifier (EG&G 5210). As a results, the sheet resistance of CNT electrode is almost similar to that of F-doped SnO2 (FTO) coated glass substrate as approximately 10 ohm/sq. From C-V and impedance spectroscopy measurements, it was found that CNT electrode has high reaction rate and low interface reaction resistance between CNT surface and electrolyte. These results provides that CNT electrode were superior to that of conventional Pt electrode. Particularly, the reaction rate in the CNT electrode is about thrice high than Pt electrode. Therefore. CNT electrode is to be good candidate material for counter electrode in DSSC.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.6
• /
• pp.1551-1558
• /
• 1994

An experiment was conducted to investigate whether an equation of heat transfer coefficient derived form energy equation of two-phase plug flow can be actually applied to the industrial field. The heat is constantly transfered to the sand beds from the wall of heat exchanger while the sand moves down through cylindrical heat exchanger by gravity from feed hooper. To increase heat transfer, turbulators such as glass ball and steel pipe packings were used. In addition, the experiment in the case of fluidizing the sand beds was also carried out. The temperatures of the sand beds and the wall were measured along the heat exchanger axis. The density and porosity of the sand beds were also measured. The deviations of the mean velocity of sands from the velocity on the wall surface because of the slip conditions on the wall were negligible (within 3%). The heat transfer coefficients when the turbulators were used and when the sand beds were fluidized were found to be much greater than those of the plain plug flow.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.13 no.4
• /
• pp.32-41
• /
• 1994

The stabilized Michelson interferometer was developed in order to measure micro dynamic displacement at the surface of solids due to elastic wave propagation. The stabilizer was designed to compensate light path disturbances using a reference mirror driven by piezoelectric actuator. Using stabilizer, the effect of external vibration was reduced and the quadrature condition was satisifed. As the results, the output of photodetector had maximum sensitivity and linearity. The minimum detectable displacement was 0.3nm at the band width of 10 MHz. The epicentral displacements due to the glass capillary breaks and the steel ball drop impact were measured using the developed interferometer and the results were compared with the calculated one.