• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.6A
• /
• pp.819-825
• /
• 2008

This paper describes the shaping formation and the erection of SCST structure by cable-tensioning. It could be a fast and economical method for constructing the space structure consisted with uniform pyramids by cable-tensioning of the cable in bottom chords. In the initial layout, the top chords and web members are left at their true length, the bottom chords are given gaps in proportion to the desired final shape. The feasibility of the proposed shaping method and the reliability of the established geometric model were confirmed with nonlinear finite element analysis and an experimental investigation on small scale and full size test models. As a result, the behaviour characteristic of MERO joint is very significant in shaping analysis of space structure. This study suggests the most reasonable modeling technique for the prediction of shaping in practices. And it is shown the characteristic of the behavior in shaping test for practical design purposes.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.3A
• /
• pp.367-373
• /
• 2008

In the design of horizontally curved plate girder web panels, it is required to evaluate accurately the elastic buckling strength under pure shear. Currently, elastic shear buckling coefficients of curved web panels stiffened by transverse intermediate stiffeners are determined by assuming conservatively that straight web panels without curvature are simply supported at the juncture between the flange and web. However, depending upon the geometry and the properties of the curved plate girder, the elastically restrained support may behave rather closer to a fixed support. The buckling strength of curved girder web is much greater (maximum 38%) than that of a straight girder calculated under the assumption that all four edges are simply supported in Lee and Yoo (1999). In the present study, a series of numerical analyses based on a 3D finite element modeling is carried out to investigate the effects of geometric parameters on both the boundary condition at the juncture and the horizontal curvature of web panel, and the resulting data are quantified in a simple design equation.

• Journal of the Korea Computer Graphics Society
• /
• v.28 no.4
• /
• pp.1-11
• /
• 2022

The Skinned Multi-Person Linear Model (SMPL) is the most widely used parametric 3D Human Model optimized and learned from CAESAR, a 3D human scanned database created with measurements from 3,800 people living in United States in the 1990s. We point out the lack of racial diversity of body types in SMPL and propose K-SMPL that better represents Korean 3D body shapes. To this end, we develop a fitting algorithm to estimate 2,773 Korean 3D body shapes from Korean body measurement data. By conducting principle component analysis to the estimated Korean body shapes, we construct K-SMPL model that can generate various Korean body shape in 3D. K-SMPL model allows to improve the fitting accuracy over SMPL with respect to the Korean body measurement data. K-SMPL model can be widely used for avatar generation and human shape fitting for Korean.

• International conference on construction engineering and project management
• /
• 2020.12a
• /
• pp.75-84
• /
• 2020

Modular construction is a construction method whereby prefabricated volumetric units are produced in a factory and are installed on site to form a building block. The construction productivity can be substantially improved by the manufacturing and assembly of standardized modular units. 3D printing is a computer-controlled fabrication method first adopted in the manufacturing industry and was utilized for the automated construction of small-scale houses in recent years. Implementing 3D printing in the fabrication of modular units brings huge benefits to modular construction, including increased customization, lower material waste, and reduced labor work. Such implementation also benefits the large-scale and wider adoption of 3D printing in engineering practice. However, a critical issue for 3D printed modules is the loading capacity, particularly in response to horizontal forces like wind load, which requires a deeper understanding of the building structure behavior and the design of load-bearing modules. Therefore, this paper presents the state-of-the-art literature concerning recent achievement in 3D printing for buildings, followed by discussion on the opportunities and challenges for examining 3D printing in modular construction. Promising 3D printing techniques are critically reviewed and discussed with regard to their advantages and limitations in construction. The appropriate structural form needs to be determined at the design stage, taking into consideration the overall building structural behavior, site environmental conditions (e.g., wind), and load-carrying capacity of the 3D printed modules. Detailed finite element modelling of the entire modular buildings needs to be conducted to verify the structural performance, considering the code-stipulated lateral drift, strength criteria, and other design requirements. Moreover, integration of building information modelling (BIM) method is beneficial for generating the material and geometric details of the 3D printed modules, which can then be utilized for the fabrication.

• Journal of Information Technology Services
• /
• v.22 no.5
• /
• pp.71-86
• /
• 2023

Recently, various geographic information systems have been used based on spatial information of geographic information systems. Accordingly, it is essential to produce a large-scale map as a small-scale map for various uses of spatial information. However, maps currently being produced have inconsistencies between data due to production timing and limitations in expression, and productivity efficiency is greatly reduced due to errors in products or overlapping processes. In order to improve this, various efforts are being made, such as publishing research and reports for automating domestic mapping, but because there is no specific result, it relies on editors to make maps. This is mainly done by hand, so the time required for mapping is excessive, and quality control for each producer is different. In order to solve these problems, technology that can be automatically produced through computer programs is needed. Research has been conducted to apply the rule base to geometric generalization. The algorithm tolerance setting applied to rule-based modeling is a factor that greatly affects the result, and the level of the result changes accordingly. In this paper, we tried to study the effectiveness of mapping according to tolerance setting. To this end, the utility was verified by comparing it with a manually produced map. In addition, the original data and reduction rate were analyzed by applying generalization algorithms and tolerance values. Although there are some differences by region, it was confirmed that the complexity decreased on average. Through this, it is expected to contribute to the use of spatial information-based services by improving tolerances suitable for small-scale mapping regulations in order to secure spatial information data that guarantees consistency and accuracy.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.3
• /
• pp.3-9
• /
• 1999

This paper presents the study on the rejection capability based on anti-phone modeling for vocabulary independent speech recognition system. The rejection system detects and rejects out-of-vocabulary words which were not included in candidate words which are defined while the speech recognizer is made. The rejection system can be classified into two categories by their implementation methods, keyword spotting method and utterance verification method. The keyword spotting method uses an extra filler model as a candidate word as well as keyword models. The utterance verification method uses the anti-models for each phoneme for the calculation of confidence score after it has constructed the anti-models for all phonemes. We implemented an utterance verification algorithm which can be used for vocabulary independent speech recognizer. We also compared three kinds of means for the calculation of confidence score, and found out that the geometric mean had shown the best result. For the normalization of confidence score, usually Sigmoid function is used. On using it, we compared the effect of the weight constant for Sigmoid function and determined the optimal value. And we compared the effects of the size of cohort set, the results showed that the larger set gave the better results. And finally we found out optimal confidence score threshold value. In case of using the threshold value, the overall recognition rate including rejection errors was about 76%. This results are going to be adapted for stock information system based on speech recognizer which is currently provided as an experimental service by Korea Telecom.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.33 no.2
• /
• pp.131-142
• /
• 2015

In order to support the development of a cost-effective river bathymetric system, this research has focused on modeling GPS observables, which are obtained by array of five single-frequency receivers (i.e., two references and three rovers) to estimate the high accurate kinematic position, and the surveying vessel altitude. Also, by applying all GPS measurements as multiple-baselines with constraining rover baselines, we derived the socalled ‘kinematic network model.’ From the model, the integer-constrained least-squares (LS) for position estimation and the implicit LS for attitude determination were implemented, while a series of simulation tests with respect to the baseline lengths around 2km performed to demonstrate its accuracy analysis. The on-the-fly (OTF) ambiguity resolution tests revealed that ninety-nine percents of time-to-fix-first ambiguity (TTFF) can be decided in less than two seconds, when the positioning accuracy of ambiguity-fixed solutions was assessed as the greater than or equal to one and two centimeters in horizontal and vertical, respectively. Comparing to the GPS-derived attitudes, the achievable accuracy gradually descended in sequence of yaw, pitch and roll due to the antenna geometric configuration. Furthermore, the RMSE values for the baseline lengths of three to six meters were within ±1′for yaw, and less than ±10′and ±20′for pitch and roll, respectively, but those of between six to fifteen meters were less than ±1′for yaw, ±5′for pitch, and ±10′for roll.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.221-221
• /
• 2014

The present work proposes an improved numerical simulator for design and modification of large area capacitively coupled plasma (CCP) processing chamber. CCP, as notoriously well-known, demands the tremendously huge computational cost for carrying out transient analyses in realistic multi-dimensional models, because electron dissociations take place in a much smaller time scale (${\Delta}t{\approx}10-8{\sim}10-10$) than time scale of those happened between neutrals (${\Delta}t{\approx}10-1{\sim}10-3$), due to the rf drive frequencies of external electric field. And also, for spatial discretization of electron flux (Je), exponential scheme such as Scharfetter-Gummel method needs to be used in order to alleviate the numerical stiffness and resolve exponential change of spatial distribution of electron temperature (Te) and electron number density (Ne) in the vicinity of electrodes. Due to such computational intractability, it is prohibited to simulate CCP deposition in a three-dimension within acceptable calculation runtimes (<24 h). Under the situation where process conditions require thickness non-uniformity below 5%, however, detailed flow features of reactive gases induced from three-dimensional geometric effects such as gas distribution through the perforated plates (showerhead) should be considered. Without considering plasma chemistry, we therefore simulated flow, temperature and species fields in three-dimensional geometry first, and then, based on that data, boundary conditions of two-dimensional plasma discharge model are set. In the particular case of SiH4-NH3-N2-He CCP discharge to produce deposition of SiNxHy thin film, a cylindrical showerhead electrode reactor was studied by numerical modeling of mass, momentum and energy transports for charged particles in an axi-symmetric geometry. By solving transport equations of electron and radicals simultaneously, we observed that the way how source gases are consumed in the non-isothermal flow field and such consequences on active species production were outlined as playing the leading parts in the processes. As an example of application of the model for the prediction of the deposited thickness uniformity in a 300 mm wafer plasma processing chamber, the results were compared with the experimentally measured deposition profiles along the radius of the wafer varying inter-electrode gap. The simulation results were in good agreement with experimental data.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.3
• /
• pp.393-400
• /
• 2009

Recently demand for the 3D modeling technology to reconstruct real world is getting increasing. However, existing geospatial data are mainly based on the 2D space. In addition, most of the geospatial data provide geometric information only. In consequence, there are limits in various applications to utilize information from those data and to reconstruct the real world in 3D space. Therefore, it is required to develop efficient 3D mapping methodology and data for- mat to establish geospatial database. Especially digital elevation model(DEM) is one of the essential geospatial data, however, DEM provides only spatially distributed 3D coordinates of the natural and artificial surfaces. Moreover, most of DEMs are generated without considering terrain properties such as surface roughness, terrain type, spatial resolution, feature and so on. This paper suggests adaptive and flexible geospatial data format that has possibility to include various information such as terrain characteristics, multiple resolutions, interpolation methods, break line information, model keypoints, and other physical property. The study area was categorized into mountainous area, gently rolling area, and flat area by taking the terrain characteristics into account with respect to terrain roughness. Different resolutions and interpolation methods were applied to each area. Finally, a 3D digital map derived from aerial photographs was integrated with the geospatial data and visualized.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.15 no.1
• /
• pp.197-210
• /
• 2012

The KOrea Multi-Purpose SATellite(KOMPSAT)-2 has a capability to provide a cross-track stereo imagery using two different orbits for generating various spatial information. However, in order to fully realize the potential of the KOMPSAT-2 stereo imagery in terms of mapping, various tests are necessary. The purpose of this study is to evaluate the possibility of mapping using the KOMPSAT-2 stereo imagery. For this, digital plotting was conducted based on the stereoscopic images. Also the Digital Elevation Model(DEM) and an ortho-image were generated using digital plotting results. An accuracy of digital plotting, DEM, and ortho-image were evaluated by comparing with the existing data. Consequently, we found that horizontal and vertical error of the modeling results based on the Rational Polynomial Coefficient(RPC) was less than 1.5 meters compared with the Global Positioning System(GPS) survey results. The maximum difference of vertical direction between the plotted results in this study and the existing digital map on the scale of 1/5,000 was more than 5 meters according as the topographical characteristics. Although there were some irregular parallax on the images, we realized that it was possible to interpret and plot at least seventy percent of the layer which was required the digital map on the scale of 1/5,000. Also an accuracy of DEM, which was generated based on the digital plotting, was compared with the existing LiDAR DEM. We found that the ortho-images, which were generated using the extracted DEM in this study, sufficiently satisfied with the requirement of the geometric accuracy for an ortho-image map on the scale of 1/5,000.