• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.266-270
• /
• 2006

Noise reduction the noise of a high precision multi-stage gearbox applied at the industrial robot is investigated by experiment such as the modal test and the signal analysis. The signal analysis performed with the waterfall plot representing the power spectrum as a function of the rotating speed. An eccentric load is installed at the gearbox in order to organize similar condition used in the industrial robot. Exciting sources are found out by the waterfall plot, and then the main factor to make the noise is distinguish. For the low-noise gearbox, the gear design parameter is modified and this gearbox is experimented in the same procedure. The results of the test show the noise level of gearbox reduced.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.27 no.1
• /
• pp.36-42
• /
• 2017

Helical gear excitation is transmitted to a gearbox through the shafts and bearings and the vibration of the gearbox radiates the noise in the air. Therefore gearbox modeling is essential to evaluate the gear noise. This work deals with vibration and acoustic analysis of a cylindrical shell-type gearbox with/without holes excited by helical gears and focuses on the development of the simple gearbox model. To do so, helical gears and bearing forces are calculated. Gearbox with/without holes is modeled by the aluminum end plates and PMMA cylindrical shell body. The vibration mode and the forced harmonic response were calculated by the commercial FE software and the end plate of the gearbox is more contributed to vibration than the body. Acoustic analysis was also conducted by the commercial acoustic software and a cylindrical shell type gearbox with/without holes has the similar vibro-acoustic characteristics.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1096-1101
• /
• 2000

In machine tools, often a gearbox is installed to control the rotating speed of spindle, which sometimes generates problems of noise and vibration due to errors in tooth-meshing. In this study, the characteristics of, noise and vibration of given gearbox for a machine tool are analyzed experimentally. From the measurement, it was observed that the tooth-meshing component of the sound pressure level from the gearbox took its maximum at a specific operational speed. Therefore, the main content of this study is to investigate the reason why the above mentioned characteristics are observed. By investigating the natural frequencies of the components in gearbox, it was found that the natural frequencies of the rotating gear-shaft and gearbox for twisting mode were closely related to the first and second peak of sound pressure levels respectively. Thereform, in this study, those relations were identified by the impact test of rotating gear-shaft and-gearbox. In addition, we inserted the rubber between housing and bed, and analyze the effect of the rubber insertion on noise reduction by Operational Deflection Shapes.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.5
• /
• pp.80-85
• /
• 2016

In recent years, work to improve the power of a tractor has been in development. This study, using the mid-PTO power of a compact tractor, attempted to develop a high-speed mid-mower by setting the rotation to more than 3,000 RPM designed/manufactured major components of the high speed mid-mower. The performance of high-speed mid-mower was evaluated by the precision of straight bevel gears, and durability, the noise of the gearbox, the gearbox internal temperature, the maximum rotation speed of the mid-mowers, and the grass cutting test. Through the performance test results, the maximum number of revolutions of the mid-mower was measured over 3,000RPM, the gearbox noise and gearbox internal temperature satisfied the performance requirements of a high speed mid-mower.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.311-315
• /
• 2012

In these days, promising renewable energy, wind turbine is clean energy but has an environmental pollutant which is noise. Noise assessment is one of the major performance evaluations for wind turbine and nowadays, developing and research for measurement and method of the assessment considering environmental pollutants is being important. Object in this study is that figuring out sound power characteristic of the gearbox for wind turbine through measuring sound intensity. In back-to-back test, we can figure out the noise characteristic of the gearbox for wind turbine through comparing and measuring sound pressure level, sound power level in operating at the each load condition respectively.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.6
• /
• pp.521-527
• /
• 2010

This article presents a method to calculate the sound radiation of transmission gearbox housing by using Helmholtz integral. Rayleigh integral is used to verify the method. Half-space radiation is considered because the actual gearbox housing is on hard place like concrete. For optimization, orthogonal array is used as a fractional factorial design method. Sound Radiation is calculated with simple source like plate and sphere shape, then actual gearbox BEM model is applied to the method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.611-616
• /
• 2002

Bearing diagnostics is difficult in a gearbox because bearing signals are masked by the strong gear signals. Self adaptive noise cancellation(SANC) is useful technique to seperate bearing signals from gear signals. While gear signals are correlated with a long correlation length, bearing signals are not correlated with a short length. SANC seperates two components on the basis of correlation length. Then we can find defect frequency component in the envelope spectrum of the bearing signals.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.362.2-362
• /
• 2002

Bearing diagnostics is difficult in a gearbox because bearing signals are masked by the strong gear signals. Self adaptive noise cancellation(SANC) Is useful technique to seperate bearing signals from gear signals. While gear signals are correlated with a long correlation length, bearing signals are not correlated with a short length. SANC seperates two components on the basis of correlation length. (omitted)

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.4
• /
• pp.70-75
• /
• 2011

Nowadays, modern gearboxes are characterized by high torque load demands, low running noise and compact design. Also durability of gearbox is specially a major issue for the industry. For the gearbox which used in wind turbine, gear transmission error(T.E.) is the excitation that leads the tonal noise known as gear whine, and radiated gear whine is also the dominant source of noise in the whole gearbox. In this paper, tooth modification for the high speed stage is used to compensate for the deformation of the teeth due to load and to ensure a proper meshing to achieve an optimized tooth contact pattern. The gearbox is firstly modeled in Romax software, and then the various combination analysis of the tooth modification is presented by using Windows LDP software, and the prediction of transmission error under the loaded torque for the helical gear pair is investigated, the transmission error, contact stress, root stress and load distribution are also calculated and compared before and after tooth modification under one torque condition. The simulation result shows that the transmission error and stress under the loads can be minimized by the appropriate tooth modification.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.537-543
• /
• 2003

Transient vibration generated by developing localized fault in gear can be used as indicators in gear fault detection. This vibration signal suffers from the background noise such as gear meshing frequency and its harmonics and broadband noise. Thus in order to extract the information about the only gear fault from the raw vibration signal measured on the gearbox this signal is processed to reduce the background noise with many kinds of signal-processing tools. However, these signal-processing tools are often very complex and time waste. Thus. in this paper. we propose a novel approach detecting the damage of gearbox and analyzing its pattern using the raw vibration signal. In order to do this, the residual signal. which consists of the sideband components of the gear meshing frequent) and its harmonics frequencies, is extracted from the raw signal by the power spectral density (PSD) to obtain the information about the fault and is used as the input data of the artificial neural network (ANN) for analysis of the pattern of gear fault. This novel approach has been very successfully applied to the damage analysis of a laboratory gearbox.