• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.593-600
• /
• 2020

The equipment for marine IoT service have to overcome the effect of seawater. Furthermore, the free floating transmitter in seawater will be less affected by the seawater environment. The results of the design and fabrication of antenna, which is embedded in buoy, are shown in this research. The proposed antenna is used to supervise the states of fishing gears in monitoring system for real-name system of electric fishing gear. The selected frequency band of the proposed antenna is 920 MHz, and PCB pattern type is selected for subminiature and light weight. It is confirmed that RF characteristics is more degraded, however, the radiation is gradually upward as the contact surface of buoy with seawater is more broaden through the simulation results. That is, the RF performance of the proposed antenna is more deteriorated but beam radiation characteristics is more suited the marine IoT, the seawater effect is more increased. It is expected that the proposed antenna will contribute the implementation of IoT network based on low power wide area (LPWA) when the degradation of RF performance will be settled.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.58 no.2
• /
• pp.141-152
• /
• 2022

As a method to understand the ecological habits around the artificial reef, various reports such as fishing gear survey, diving, sound survey, underwater CCTV and camera, etc. are reported. Among them, the sound survey method is carried out by installing an acoustic system on the ship and can be investigated regardless of the marine environment such as time constraints and turbidity. Such method, however, takes a lot of manpower and time as the ship travels at a constant speed. Investigations around artificial reefs are being conducted in an artificial way, and a lot of time and labor are consumed as such. Maritime buoys have been operated for various purposes such as route signs, weather observation, marine environment monitoring and defense monitoring for navigation safety in the past, but studies on monitoring systems for ecological habits and distribution of fish using marine buoys are remarkably insufficient. Therefore, this study aims to develop a system that allows users to directly monitor fish group detector data by estimating the distribution of fish groups around artificial reefs and using wireless communication at sea. In order to confirm the suitability of the maritime buoy used in this study, it was operated to compare data using LTE-equipped buoys capable of wireless communication and a data logger-type system buoy. Data transmission of buoys capable of LTE communication was carried out in a 10-minute ON, 10-minute OFF method due to the limitation of the power supply capacity, and data of the data logger-type buoy received full data. We compared and analyzed the data received from the two fish detectors. It is expected that real-time monitoring of the wireless buoy detection device using LTE will be possible through future research.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.3
• /
• pp.571-580
• /
• 2022

Marine deposited waste is a major cause of problems such as a lot of damage and an increase in the estimated amount of garbage due to abandoned fishing grounds caused by ghost fishing. In this paper, we implement a real-time marine deposited waste detection artificial intelligence system to understand the actual conditions of waste fishing gear usage, distribution, loss, and recovery, and study methods for performance improvement. The system was implemented using the yolov5 model, which is an excellent performance model for real-time object detection, and the 'data screening process' and 'class segmentation' method of learning data were applied as performance improvement methods. In conclusion, the object detection results of datasets that do screen unnecessary data or do not subdivide similar items according to characteristics and uses are better than the object recognition results of unscreened datasets and datasets in which classes are subdivided.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.6
• /
• pp.163-170
• /
• 2023

With the introduction of the law regarding severe penalties for major accidents, employers, management executives, and corporations have significantly increased the number of safety managers and invested extensively in acquiring ISO certifications to prevent accidents in industrial sites. Moreover, the implementation of the Smart Safety Management System (SSMS) has facilitated the management of personnel and safety equipment. While IoT-based management systems have been applied to safety gear such as helmets, safety harnesses, and protective clothing, the responsibility for safety shoes still primarily lies with on-site managers and individuals, leaving a vulnerability to accidents. In this study, we aim to implement a Raspberry Pi-based sensor device to proactively detect workers' safety shoe usage upon entering the site. The goal is to confirm the usage of safety shoes and prevent accidents that may occur due to non-compliance with safety shoes regulations.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.26 no.2
• /
• pp.118-124
• /
• 1990

The rope winder in addition to the line hauler was used for recoiling of the main line to the rope pond at the stern, however, catching the loops, evenly revoiling and arrangements of the loops were done manually by two men. The automatic loop catcher under the rope winder was consisted with the rotary lever, semicircle guide plates, transfer belt and swing rope receiver for arrangements of the loops and evenly recoiling. The obtained results are as follows: 1. The minor diameter of a loop and the diameter of the coiling pile in a lead core PP rope(ø 10mm) are about 14cm and 60cm while the rope is piled on the bottom. 2. Distribution ratio of the loops within upper or lower 10cm from the transfer belt is 93% with a lead sinker and 98% without sinker using by the smaller loop catcher. 3. The relationship between revolutions of the rotary lever N sub(1) (rpm) and the hauling pulley N sub(p) (rpm) by gear ratio 3:1 in the smaller loop catcher is as follows: N sub(p) =2.86 N sub(1) +23.74 and optimum ratio of horizontal speed of the loops by the rotary lever to hauling speed is about 70%. 4. The rope receiver is swung front and rear for the evenly recoiling and its period can be controlled by gear ratio or hydraulic circuit in accordance with the interval of the loops.

• Journal of Biosystems Engineering
• /
• v.43 no.1
• /
• pp.1-13
• /
• 2018

Purpose: The development of compact tractors that can be used in dry fields, greenhouses, and orchards for pest control, weeding, transportation, and harvesting is necessary. The development and performance evaluation of power transmission units are very important when it comes to tractor development. This study evaluates the performance of a driving power transmission unit of a 50 kW multi-purpose narrow tractor. Methods: The performance of the transmission and forward-reverse clutch, which are the main components of the driving power transmission unit of multi-purpose narrow tractors, was evaluated herein. The transmission performance was evaluated in terms of power transmission efficiency, noise, and axle load, while the forward-reverse clutch performance was evaluated in terms of durability. The transmission's power transmission efficiency accounts for the measurement of transmission losses, which occur in the transmission's gear, bearing, and oil seal. The motor's power was input in the transmission's input shaft. The rotational speed and torque were measured in the final output shaft. The noise was measured at each speed level after installing a microphone on the left, right, and upper sides. The axle load test was performed through a continuous equilibrium load test, in which a constant load was continuously applied. The forward-reverse clutch performance was calculated using the engine torque to axle torque ratio with the assembled engine and transmission. Results: The loss of power in the transmission efficiency test of the driving power unit was 6.0-9.7 kW based on all gear steps. This loss of horsepower was equal to 11-18% of the input power (52 kW). The transmission efficiency of the driving power unit was 81.5-89.0%. The noise of the driving power unit was 50-57 dB at 800 rpm, 70-77 dB at 1600 rpm, and 76-83 dB at 2400 rpm. The axle load test verified that the input torque and axle revolutions were constant. The results of the forward-reverse clutch performance test revealed that hydraulic pressure and torque changes were stably maintained when moving forward or backward, and its operation met the hydraulic design standards. Conclusions: When comprehensively examined, these research results were similar to the main driving power transmission systems from USA and Japan in terms of performance. Based on these results, tractor prototypes are expected to be created and supplied to farmhouses after going through sufficient in-situ adaptability tests.

• Analytical Science and Technology
• /
• v.26 no.4
• /
• pp.276-286
• /
• 2013

This study was performed to investigate the contents characteristics of hazardous oil wastes and wastes of liquid fuels from different industrial process. In order to establish a hazardous waste list, samples of various industrial discharge have been analyzed for 16 non-regulated inorganic hazardous substances (i.e., Cu, Pb, Cd, CN, Hg, As, T-Cr, $Cr^{6+}$, Sb, Ni, F, V, Ba, Zn, Be, Se). In more detail, hazardous waste samples including waste hydraulic oils, waste engine, gear and lubricating oils, waste insulating and heat transmission oils, bilge oils, oil/water separator contents processing were collected from 37 workplaces and analyzed. We observed that the most of the inorganic substances exceeded the proposed criteria in many samples. Especially the concentration of Sb in heat transmission oil, bilge oil and gear & lubricating oils were ranged from 6 to 419 mg/kg whereas the proposed criteria is 50 mg/kg. The assessment result of hazardous waste in Korea according to the EWC showed that the out of 24 processes, 16 belongs to absolute entry and 8 belongs to mirror entry. In conclusion, we expect the outcome of this study to align the classification system of hazardous waste management in South Korea with international legislations, and consequently contribute to reduce environmental pollution as well as health risks by toxic wastes.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.237-246
• /
• 2019

The Electro-Mechanical Brake (EMB) is the next generation braking system for automobiles and railway vehicles. Current brake systems for high-speed trains generate a braking force using a pneumatic cylinder, but EMB systems produce that force through a combination of an electric motor and a gear. In this study, an EMB operation mechanism capable of generating a high braking force was proposed, and structural and vibration analyses of the gears and shafts, which are the core parts of the mechanisms, were performed. Dynamic structural analysis confirmed that the maximum stress in the analysis model was within the yield strength of the material. In addition, the design that maximizes the diameter of the motor shaft was found to be advantageous in strength, and large shear stress could be generated in the bolt fixing the gear and eccentric shaft. In addition, a test apparatus that can reproduce the mechanism of the analytical model was fabricated to measure the strain of the fixed bolt part, which is the most vulnerable part. The strain measurement results showed that the error between the analysis and measurement was within 10%, which could verify the accuracy of the analytical model.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.493-501
• /
• 2016

In this study, core technologies of a traction system on a mountain tram operating on the track of mountain road full of sharp curves and steep gradients were developed. In domestic mountain resort areas, sometimes the transportation service is not provided in winter because of ice and heavy snow on roads, so a mountain railway service independent of the climate and geographic conditions is needed. A traction system was designed taking into account of the power of a traction motor to climb the gradient of 120 ‰, which is common in domestic mountainous areas. and power transmission system was designed to consider the installation space for the traction system. In addition, a reduction gear and a propeller shaft were developed. An elastic pinion was developed and applied to the rack & pinion bogie system for steep gradient so that noise and vibration generated by contact between the steel gears could be reduced. Impact comparison tests showed that the vibration level of the elastic pinion is one-third lower than that of previous steel pinion. Independent rotating wheels and axles were developed for the bogie system to operate on the sharp curve of a 10 meter radius. In addition, the band braking system was developed to enhance the braking force during running on the steep gradient. A test for the braking force showed it exerts the required braking force. The performance of the developed core components were verified by the tests and finally they were applied to the bogie system running on the track of steep gradient and sharp curve.

• Economic and Environmental Geology
• /
• v.49 no.6
• /
• pp.479-490
• /
• 2016

Seabed drilling system has recently been used to drill seafloor mineral resources. This case report highlights the procedure and result of sea-trial of seabed drilling system at off-shore of Japan on March, 2016 as well as briefs an international-technical trend of seabed drilling system. In case of having less than 100 m drill depth, seabed drilling system is favorable for seafloor mineral deposits which are mostly distributed within a narrow district and situated between 1000~3000 m water depth, compared with vessel-mounted drilling system. The system is featured by the remotely-operated drill gear, which has top drives, drill strings and mud system on it. The core samples are generally recovered to ship with seabed driller after a dive. In this sea-trail, recovery rate of core samples averagely shows about 55% and the recovered rocks mostly correspond to fresh and/or weak-altered basalt. In case of drilling hydrothermal ore deposit, the recovery rate would be lower than 55% because of the fragile nature of ores. Alternatively it is used to collect cutting chips through riser or bins in order to increase the recovery rates. Recently a reverse circulation method is taken considered to acquire the better cutting-chips. Three-leg type outrigger system and four-leg type leveling system are the competing landing-instruments of seabed drill system. However the landing efficiency using these gears has to be further monitored due to lack of case reports.