• Journal of Navigation and Port Research
• /
• v.38 no.6
• /
• pp.637-643
• /
• 2014

This study aims to explore a set of indicators to be used for purification management. by estimating the total quantity of depositied waste in coastal waters, Through 3 rounds of Delphi technique, this study sorts out the following 5 variables to be used as major indicators determining priorities for purification in coastal areas: the ratio of re-deposition after collection, the area where fishing gear are lost, the total quantity of depositied waste of each coastal water, the total quantity of deposited waste in the past, and the quantity of depositied waste by unit area. Although the fact that the delphi surveys were done only on 27 specialists limits its external validity, this study will serve as a base for in-depth studies with more expanded panels that will provide better indicators for purification management in coastal waters of Korea.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.2
• /
• pp.166-173
• /
• 2012

Plug-in Hybrid Electric Vehicle is driven by the engine, the primary traction motor, and the secondary auxiliary motor generating the electric power for battery charging. Secondary auxiliary motor should be connected to the engine or separated from the engine by the clutch system. This paper presents the position controller of the BLDC motor for the clutch system of Plug-in Hybrid Electric Vehicle. The BLDC motor can be applied to the clutch system in spite of it's low accuracy of the position control due to high gear ratio between the clutch and the motor. Since the attachment and the detachment between the motor and the engine should be carried out within 0.3 seconds, the position controller with fast acceleration and deceleration is implemented. For the torque control with braking operation for the BLDC motor, the modified bipolar PWM method with low current ripple compared to the conventional unipolar PWM is presented. The position control performance of the BLDC motor for the clutch system is verified through the simulation and experiments.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.52 no.3
• /
• pp.232-240
• /
• 2016

Marine casualties originated from fishing vessels occupied about 71.2% of the whole marine casualties in Korea from 2008 to 2014, which has not changed much for a long time. Therefore, a pragmatic counterplan to decrease in casualties in fishing vessel is indispensable for reduction of marine casualties in Korea. Since the casualties occurred by fishing vessels may incline to a specific type of casualties according to the difference in the operating type; in this paper, 11 fishing types which occurred casualties frequently in numbers and occupied ratio were selected. Since the most frequent occurring casualties in fishing vessels were from collisions and fire explosion in statistics from KMST (2008~2014), the study focused on them. The collision is given a great deal of weight in all the casualties mostly due to the negligence of duty regardless of the job types. Gill netter, trap fishing boat, jig boat, multiple fishing boat and stow netter have their own specific causes of casualties in collision according to the operating types. The cause of fire explosion was mainly due to poor inspection and maintenance the electric cord. For this reason, it may be necessary for an operator to make strict precaution on the other vessels under way systematically, keep the regulation for preventing collisions, and for an engineer on watch to make a check the electricity periodically to reduce the fire explosion.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.4
• /
• pp.454-462
• /
• 2016

This study was conducted in order to estimate the exhaust emissions analysis method of the real driving emission(RDE). The Association for Emissions Control by Catalyst(AECC) has developed a test procedure by using a random cycle method based on the chassis dynamometer. In order to confirm this approach in Korea, Euro 5(DPF), Euro 6(DPF + LNT), and Euro 6(DPF + SCR) were performed on three different vehicles to determine the exhaust gas characteristics of the random cycle, real-road driving test(PEMS), and emission certification driving mode(NEDC). Six different random cycle driving modes were generated by the vehicle specifications(e.g. curb weight, engine power, gear ratio, and maximum acceleration). The NOx emissions were increased in the NEDC, random cycle, and PEMS order in this study regardless of the test vehicles. The random cycle method has the advantage because it utilizes a chassis dynamometer in the laboratories for a repeatable data collection, and it allows any eminent emission improvement checked prior to a real-road driving test with PEMS.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.3
• /
• pp.255-262
• /
• 2014

To investigate the effect of oil on evaporation heat transfer of plate heat exchanger, evaporation heat transfer experiment was carried out using experimental apparatus for micro gear pumped R134a-oil circulation. By varying oil circulation rate of POE oil from 0 to 5%, evaporation heat transfer performance of plate heat exchanger was investigated. As OCR(Oil Circulation Ratio) increases, the evaporation heat transfer coefficient of R134a decreases and pressure drop increases. When the evaporating temperature is $30^{\circ}C$ and the refrigerant mass flow rate is 80 g/s, evaporation heat transfer rate decreases by 10 % and pressure drop increases by 10% at 2% of OCR condition.

• Proceedings of the KIEE Conference
• /
• 2002.06a
• /
• pp.187-190
• /
• 2002

In contrast to conventional electromagnetic motor, USM(Ultrasonic Motor), as piezoelectric ceramic applying ultrasonic mechanical vibration and as frictional-movement type motor, get rotational torque by elastic friction between stator and rotator, The USM, which is small motor without iron cores and coil as a simple structure, has little load weight, has character of high torque at low speed, and can apply a direct drive type without deceleration gear as low speed type. A response of USM from control input is satisfactory, and also generates much torque in low speed driving, and holding torque is much without supplying power. In this study, I designed and made Ultrasonic motor-digital multi controller(USM- DMC) using FPGA chip, A54SX72A made in Actel Corporation. By the minute, USM-DMC can control frequency, duty ratio, and phase difference of USM by llbit digital input from Pc. Therefore, when we use this controller, we can apply to typical parameter, frequency, phase difference, and voltage parameter, to control as well as we can do mixing control like phase-frequency, phase-voltage, frequency-voltage, frequency-phase-voltage, What is more, the strongest point is that it can trace frequency based on optimized frequency because we can input optimized resonant frequency while in motoring.

• Korean Journal of Agricultural Science
• /
• v.49 no.4
• /
• pp.845-855
• /
• 2022

The purpose of this study is to develop a self-propelled underground crop harvester and its performance was evaluated by measuring the load during actual potato harvesting operations. This study was conducted at a constant working speed of 1 km·h^-1. A load measurement system was installed to measure the actual load and the required working power was analyzed. A hydraulic pressure sensor was also installed to measure the hydraulic pressure. The required hydraulic power was calculated using the hydraulic pressure and flow rate. The results showed that the engine speed, torque, and power during harvesting operation were in the range of 845 - 1,423 rpm, 95 - 228 Nm, and 9 - 31 kW, respectively. Traction power, excluding the hydraulic pump of the tractor and power take-off (PTO) output, was in the range of 9 - 28 kW, and it was confirmed that it occupies a ratio of 16.2 to 50% of the engine rated output. The engine can supply the minimum required traction power to move the vehicle. This means that the engine used in this study could be down-sized to be suitable for an underground crop harvester. In this study, the gear stages of the tractor were not considered. This research thus shows the possibility of developing a self-propelled underground crop harvester.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.14 no.2
• /
• pp.63-68
• /
• 1978

A boat seine has been used as a major fishing gear for catching anchovy (Engraulis japonica) in the southern coastal waters of Korea since the 1920s. Since the 1950s some improvement from the original seine has been made; powered boats equipped with net hauler has been used instead of rowing boats with hand-driven capstan, and the seining method has been changed into the trawling method. But even now, there are many problems to be solved in the view point of decreasing man power without decreasing catching efficiency. For the purpose, patti-net has been introduced from Japan and experimented on the commercial base since 1972, and it was known that the patti-net could be operated with man power as half as needed in the coventional net, but catching efficiency was not so desirable. Therefore, the study on the characteristics of it were required. The authors carried out a model experiment with a Qne-twentieth scale model net towed by a powered boat on the sea. The obtained results run as follows: 1. Hydrodynamic resistance of the model net can be explained as $R_p=69.6 V_{I.66}$ $R_h=37 v^2$ where $R_p$ and $R_b$ denote the resistance of the whole gear and the cod end in kg respectively, and v the towing speed in mlsec. 2. Performance of wing and cod end showed no deformation such as observed at the conventional net. 3. The ratio of opening at the entrance of bag net to that of cod end showed about 2: 1. Therefore, when we intend to enlarge the net to be able to operate in the deep fishing ground, the cod end should be enlarged in the same proportion and increased towing power is needed .. Then, it will be better to increase the ratio for increasing fishing efficiency without increasing towing power.

• The Journal of the Korea Contents Association
• /
• v.13 no.12
• /
• pp.860-868
• /
• 2013

The purpose of this study is to ensure safety by measuring External radiation dose ratio (ERDR) by traits of patients in many ways after administering radiopharmaceutical($^{18}F$-FDG) for PET Torso scan, and to decrease ERDR of those to RI technologist, caretakers, and those who frequently exposed to radiation by arousing attention to radiation dose. Radiopharmaceutical was administered to 80 patients who conducted PET Torso from January to June, 2013. Radiation dose emitted from the patients was measured according to body shape(BMI), water hydration, height, amount of radiation administration. From the moment immediately after the radiopharmaceutical was administered, ERDR was measured by personal traits of patients. The radiation dose increased in proportion to the administered amount of the radiopharmaceutical, and there was no significant difference depending on the body shape of the patients. When water was supplied and the height was normal, the radiation dose was lower compared with the cases where water was not supplied and height was not normal. There is a need for making efforts to minimize the working time through sufficient education and mock training before those who RI technologist with sources of radiation for complying the radiation safety management rule. And they should minimize the ERDR by wearing a protective gear.

• Journal of Biosystems Engineering
• /
• v.3 no.1
• /
• pp.20-36
• /
• 1978

The effect of binder kicking forces on the shattering losses of paddy rice, which has been widely understood as an outstanding loss factor in harvesting with a binder, were experimentally assessed in this thesis.Through the field tests the optimum time of harvest, in terms of grain moisture contents, was found by considering harvesting losses for two rice varieties, harvested by two different binders, at four or five grain moisture levels.A device was designed and manufactured to apply various kicking forces to the bundles and was used in the bundle kicking tests. It was intended to find out the optimum range of kicking force to minimize the kicking losses. Based on the study, modification of the existing binder kicking mechanism was suggested. The following is a summary of the results of this thesis. 1. In Suweon 258 variety, as the grain moisture content is reduced, so the cutting loss and the kicking loss increase. The grain losses range from 0.77 to 0.82 percent of total field yield for the cutting loss, from 1.83 to 2.01 percent for the kicking loss, and from 2.60 to 2.83 percent for the field loss, when the moisture content is about 22 percent. 2. In Jinheung variety , the field losses increased as the grain moisture content decreased . When the moisture content was 20 percent, the field loss, cutting loss and kicking loss was 0.42-0.49 % , 0.30-0.35, and 0.12 -0.14% of the total field yield, respectively. 3. The difference in the field loss , cutting loss, and kicking loss for the two binders was 0.23% , 0.05% and 0.18% respectively in Suweon 258 variety, and 0.07% , 0.02% and 0.05% respectively ini Jinheung variety. The grain losses for binder B were slightly higher than those for binder A. 4. In the statistical analysis of each variety , the kicking force and the moisture content of the grain, and its interaction were all highly significant at 1% level by T test .The optimum kicking force was found to be in the 3.0-0.4kg range. This does not interrupt the binder operation, while ioses are kept to an acceptale level. 5. To reduce the kicking force of the eXlstmg binder mechanism, the speed of rotation of the kicking arm needs to be redued by increasing the number of driving sprocket teeth, and the position and gear ratio of the knotter-bill and driving bevelgear have to be change to give a !motter-bill speed of 1110 rpm. It is also desirable to attach a belt conveyor which smoothly carries the bundle to the ground. 6. The optimum harvesting time cased on maximum field yield was found to be at a grain moisture content of around 22 percent for Suweon 258 variety, and 20 percent for Jinheung variety. Tota] field yield and field yield at the time amounted to 9, 812.5 kg/ha, 9, 302. 5kg/ha respectively for the Suweon 258, and 7, 819.5 kg/ ha, 7, 158.7 kg/ha respectively for the Jinheung variety.