• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.64-74
• /
• 2005

The effect of fuel injection spray on engine performance has been known as one of the major concerns for improving fuel economy and reducing emissions. In general, reducing the spray droplet size could prevent HC emission in gasoline engine. As far as PFI gasoline engine is concerned, the mixture of air and fuel may not be uniform under a certain condition, because breakup and production of spray droplets are made in a short distance between the fuel injector and intake valve. This study, by constituting PFI gasoline spray system, was performed to study the transient spray characteristics and dynamic behavior of droplets from two-holes two-sprays type injector used in DOHC gasoline engine. Mean droplet size and optical concentration in accordance with various conditions were measured by LDPA and CCD camera. Through this study, the variation of drop size and optical concentration could be used for understanding the behavior of unsteady spray was declared and the existing the small droplets between each pulse spray could be estimated caused to the development of wall film was conformed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.3
• /
• pp.65-72
• /
• 2011

In this study, the numbers, sizes of particles from a single cylinder direct injection spark-ignition (DISI) engine fuelled with gasoline and LPG are examined over a wide range of engine operating conditions. Tests are conducted with various engine loads (2~10bar of IMEP) and fuel injection pressures (60, 90, and 120 bar) at the engine speed of 1,500 rpm. Particles are sampled directly from the exhaust pipe using rotating disk thermodiluter. The size distributions are measured using a scanning mobility particle sizer (SMPS) and the particle number concentrations are measured using a condensation particle counter (CPC). The results show that maximum brake torque (MBT) timing for LPG fuel is less sensitive to engine load and its combustion stability is also better than that for gasoline fuel. The total particle number concentration for LPG was lower by a factor of 100 compared to the results of gasoline emission due to the good vaporization characteristic of LPG. Test result presents that LPG for direct injection spark ignition engine help the particle emission level to reduce.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.6
• /
• pp.31-39
• /
• 2000

In this paper, characteristics of a port injection type LPG fuel system were investigated to adopt the system to a spark ignition engine through rig test. Engine combustion characteristics for limited conditions and the precise control method of LPG fuel supply were also studied. As a basic experiment, the effects and the relationships of parameters such as orifice area, fuel delivery pressure, fuel temperature and flow coefficient were established. From this, one dimensional compressible flow equation can be applied to control gaseous fuel flow rate by setting pressure difference between vaporizer and manifold to a certain range, for example about 1.2 bar in a naturally aspirated engine. The combustion analysis results of LPG engine were also compared with those of gasoline engine according to spark timing and load change. At part load and stoichiometric condition, the MBT spark timing of LPG fueled engine is retarded by 2$^{\circ}$ - 4$^{\circ}$CA compared to that of gasoline engine. On the contrary, the spark timing of LPG fueled engine can be advanced by 5$^{\circ}$- 10$^{\circ}$ CA at WOT, which results from higher Octane Number and burned fraction of LPG fuel compared to gasoline.

• 제어로봇시스템학회:학술대회논문집
• /
• 1997.10a
• /
• pp.484-487
• /
• 1997

In this paper a simulation program for the powertrain control of a gasoline engine with automatic transmission is presented, The object-oriented programming approach has been pursued, and MATLAB/ SIMULINK was adopted for its environment. The purpose of the paper is to demonstrate the programmability of a control system in the object-oriented fashion so that the transferability of the objects is guaranteed. The program developed in the paper was applied to a gasoline engine and the mathematical models used in the paper were just adopted from the literature. It is shown that the simulation results and real experimental results coincide well. Therefore, it is expected that the program or objects made in the paper are useful for the automotive engineers when they design a new engine/transmission system or modify a part of existing system.

• Journal of Industrial Technology
• /
• v.17
• /
• pp.339-344
• /
• 1997

DOHC gasoline engine(4-cylinder in line type, 1600cc) is modified for the experiment to develope an alternative fuel. The modified engine is tested with the various combination of gasoline and methanol. Pollutant emissions of CO and HC are measured at the end of exhaust manifold. The concentration of CO and HC in exhaust gas is greatly reduced with the increase of coolant temperature of engine. HC concentration is reduced until methanol content reaches to thirty percent and then increased with the volumetric percentage of methanol in fuel. On the other hand, the concentration of CO is reduced as the methanol centent is increased up to 20 percent and then it becomes constant even though the methanol content is raised. The effect of engine RPM on the HC and CO exhaust is investigated. HC concentration is reduced as the engine RPM is increased but the typical trends of variation are not found in the measured value of CO concentrations.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.3046-3056
• /
• 1994

To design and develop a turbocharged engine, it needs that many studies must be preceded about the characteristics of engine performance and thermal flow. To accomplish this purpose, turbocharger was equipped to 1.3 liter naturally aspirated gasoline engine. The temperature probe of plate type was designed and it was installed into the combustion chamber wall to measure unsteady temperature. The unsteady heat flux at combustion chamber wall was evaluated using one dimensional unsteady conduction equation with the wall temperature and temperature gradient.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.3
• /
• pp.46-54
• /
• 1993

In order to develop a fuel-efficient gasoline engine oil, an experimental study was conducted using an engine dynamometer, a passenger car and the SRV machine. Oil samples with different viscosity were prepared by adding several friction modifiers to select the best one and also to investigate the effect of the viscosity grade. From the study, we have developed engine oils which result in good fuel economy. The viscosity grade of 7.5W/30 was best among the oils investigated with respect to fuel economy and a fatty amine type friction modifier had the good fuel-economy property.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.7
• /
• pp.1-14
• /
• 1999

In the present study, the flame factor which primarily influence the simulation accuracy of the combustion process in a gasoline engine was modeled as a nonlinear function of turbulent intensity to laminar flame speed ratio. Multi-length-scale production rate model for turbulent kinetic energy equation was introduced to consider the different length scales of the swirling and tumbling motions in cylinder on the production rte of turbulent kinetic energy. By7 introducing the multi-length-scale production rate model for the turbulent kinetic energy equation, the predictions of turbulent burning velocity , cylinder pressure, mass burning rate and engine performance of a gasoline engine can much be improved.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.11
• /
• pp.775-784
• /
• 2017

The purpose of this study was to analyse the basic data of the engine tuning inspection by confirming the working possibility of effective engine tuning and identifying the characteristics of tuned engine that are no problem with the safety operation and environment in a driving gasoline car. The effects of tuned engine on the characteristics of air/fuel ratio and performance at a wide range of engine speeds were experimentally investigated by the actual driving car with a four-cycle, four-cylinder DOHC, turbo-intercooler, water-cooled gasoline engine operating under four types of non-tuning, and tuning 2-1, 2-2 and 2-3. The tuned parts of engine in a driving gasoline car include the intake manifold, intake pipe, air filter, exhaust manifold, exhaust pipe and silencer. In this experiment, the air-fuel ratio and torque of both non-tuned and tuned engines that one person took on board in the car with a five-speed automatic transmission were measured by the chassis dynamometer(Dynojet 224xLC). It was found that the maximum torque of tuned engine in a driving gasoline car was increased by 103.68% on average, while the maximum output was increased by 119.68% on average in comparison to the non-tuned engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.1
• /
• pp.157-164
• /
• 2014

Dual fuel combustion strategy with di-methl ether (DME) and gasoline was tested in a compression ignition engine. Characteristics of combustion and emissions were analyzed with the variation of engine operating parameters such as fuel proportion, DME injection timing, intake oxygen concentration, DME injection pressure and so forth. Gasoline was injected into the intake manifold to form the homogeneous mixture with intake charge and DME was injected directly into the cylinder at the late compression stroke to ignite the homogeneous gasoline-air mixture. Dual fuel combustion strategy was advantageous in achievement of higher thermal efficiency and low NOx emission compared with DME single fuel combustion. Higher thermal efficiency was attributed to the lower heat tranfer loss from the decreased combustion temperature since the amount of lean premixed combustion was increased with the larger amount of gasoline proportion. Lower NOx emissions were also possible by lowering the combustion temperature.