• 한국산학기술학회논문지
• /
• 제21권5호
• /
• pp.623-629
• /
• 2020

본 연구는 항공기 기총발사 비행조건에서 Gun Port 주변 공기 유동장을 분석하여 디버터(Diverter) 옵션 형상에 따른 Gun Gas 유동량 및 경로를 확인하고 항공기 성능 및 안전성 영향을 확인하였다. Gun Port Diverter는 기총사격 시 발생하는 열을 효과적으로 낮춰주는 역할을 할 뿐아니라 Gun Gas를 상향방향으로 효율적으로 배출시키는 역할을 수행하며, 그 형상에 따라 Gun Gas 경로가 변경될 수 있다. 후방 Gun Port Diverter의 옵션 형상에 따라 기총 발사 시 Gun Gas의 유량, 경로, 압력을 분석하였다. Gun Port 내부 속도분포와 온도변화를 분석한 결과 후방 Diverter를 지나는 유량은 옵션 형상에 따라 급격이 감소하는 경향을 보이지만, 전방을 지나는 유량은 변화가 적은 비슷한 경향을 보임을 확인하였다. 따라서 기총발사 시 발생하는 Gun Gas는 후방 Gun Port Diverter 옵션 형상과 관계없이 항공기 표면에서 충분한 유동 거리가 확보되며, Diverter 옵션 형상에 따른 Gun Gas 유동의 정체는 Gun Port 내부 온도 상승에 큰 영향을 미침을 확인하였다.

• 동력기계공학회지
• /
• 제6권4호
• /
• pp.23-29
• /
• 2002

This paper is studied to investigate the effect of slits and swirl vanes on the main flow fields of a gun-type gas burner through X-Y plane and Y-Z plane respectively by using X-probe from hot-wire anemometer system. This experiment was carried out with flow rate $450{\ell}/min$ in respective burner models installed in the test section of a subsonic wind tunnel. The burner models with only slits and only swirl vanes respectively were made by modifying original gun-type gas burner. The fast jet flow spurted from slits played a role such as an air-curtain because it encircled rotational flow by swirl vanes and drives mixed main flow to axial direction. As a result, the gun-type gas burner had a wider flow range up to about Y/R=1.5 deviated from slits and maintains a comparatively large velocity in the central part of burner within the range of about X/R=2.5. Therefore, it was very desirable that swirl vanes were installed within slits in gun-type gas burner in order to control the main flow fields effectively.

• 한국소음진동공학회논문집
• /
• 제12권5호
• /
• pp.389-396
• /
• 2002

In this study, the dynamic absorbing system for gas operated gun has been investigated. For this purpose, firstly. mathematical model of gas-operated shoulder-fired gun has been constructed. Through a series of experimental works using the devised test setup, the characteristic behavior of mathematical model was compared to the test results. In order to design the dynamic absorbing system, parameter optimization process has been performed based on the simplified isolation system under constraints of moving displacement and transmitted force. In order to implement the more efficient dynamic absorbing system, the characteristic performance of stroke-dependent variable damping system has been analyzed with some opening area curves. Finally, the performance of the designed dynamic absorbing system has been evaluated by simulation and experiment using the previous test apparatus.

• Journal of Mechanical Science and Technology
• /
• 제18권10호
• /
• pp.1819-1828
• /
• 2004

The purpose of this paper is to investigate the effects of slits and swirl vanes on the turbulence augmentation in the flow fields of a gun-type gas burner using an X-type hot-wire probe. The gun-type gas burner adopted in this study is composed of eight slits and swirl vanes located on the surface of an inclined baffle plate. Experiment was carried out at a flow rate of 450 ι/min in burner model installed in the test section of subsonic wind tunnel. Swirl vanes playa role diffusing main flow more remarkably toward the radial direction than axial one, but slits show a reverse feature. Consequently, both slits and swirl vanes remarkably increase turbulence intensity in the whole range of a gun-type gas burner with a cone-type baffle plate.

• 동력기계공학회지
• /
• 제19권1호
• /
• pp.19-23
• /
• 2015

The swirling flow fields of a gun-type gas burner(GTGB) without a combustion chamber were measured by a straight-type five-hole pressure probe(FHPP) under the cold flow condition. The three kinds of velocity components and the static pressure were calculated by using a non-nulling calibration method covering the velocity reduction performance of the effective flow attack angle of ${\pm}80^{\circ}$. As a result, the velocity and static pressure measured by a FHPP comparatively shows the better performance on the swirling flow of a GTGB than those measured by X-probe.

• 한국항공우주학회지
• /
• 제46권9호
• /
• pp.774-781
• /
• 2018

본 연구에서는 쿼드콥터형 소형 무인 드론에 이산화탄소를 작동 기체로 하는 가스총을 설치하여 가축 방역에 응용할 수 있는 발사체 및 결합 유닛을 개발하였다. 시스템은 상용 드론과 가스총, 솔레노이드 밸브, 무선 통신 제어기 등으로 구성된다. 발사된 탄환의 속도를 측정하고, 지상 시험, 실제 비행체에의 탑재 시험 등을 거쳐 최종 검증하였다. 본 연구 개발을 통하여 농업, 소방 등의 다양한 방역 및 방재 분야에 발사체 기술을 적용할 수 있는 가능성을 확인하였다.

• Journal of KIEE
• /
• 제10권1호
• /
• pp.16-22
• /
• 2000

The Main role of the gas turbine lies in the utilization of waste heat which may be found in exhaust gases from the gas turbine or at some other points of the process to produce additional electricity. Up to date, the PID controller has been used to operate under such difficult conditions, but since the gain of PID controller manually experience. In this paper parameter separation type 2-DOF PID controllers are proposed based on the gas turbine control system. Gas turbine transfer function is achieved from operation data of Gun-san gas turbine and Tuning algorithms of parameter separation type 2-DOF PID controller is ANFIS. Results represents satisfactory response.

• 대한기계학회논문집B
• /
• 제27권4호
• /
• pp.466-475
• /
• 2003

The gun-type gas burner adopted in this study is generally composed of eight slits and swirl vanes. Thus, this paper is studied to investigate the effect of slits and swirl vanes on the turbulent flow fields in the horizontal plane of gas swirl burner with a cone type baffle plate measured by using X-probe from hot-wire anemometer system. This experiment is carried out at flow rate 450 $\ell$/min in the test section of subsonic wind tunnel. The axial mean velocity component in the case of burner model with only swirl vanes shows the characteristic that spreads more remarkably toward the radial direction than axial one, it does, however, directly opposite tendency in the case of burner model with only slits. Consequently. both slits and swirl vanes composing of gun-type gas burner play an important role in decrease of the speed near slits and increase of the flow speed in the central part of a burner because the biggest speed spurted from slits encircles rotational flow by swirl vanes and it drives main flow toward the axial direction. Moreover, the turbulent intensities and turbulent kinetic energy of gun-type gas burner are distributed with a fairly bigger size within X/R<0.6410 than burner models which have only slits or swirl vanes because the rotational flow by swirl vanes and the fast jet flow by slits increase flow mixing, diffusion, and mean velocity gradient effectively.

• 한국분말재료학회지
• /
• 제21권1호
• /
• pp.44-49
• /
• 2014

In this study, nanocrystalline nickel powders were cold compacted by a dynamic compaction method using a single-stage gas gun system. A bending test was conducted to measure the bonding strengths of the compacted regions and microstructures of the specimen were analyzed using a scanning electron microscopy. The specimen was separated into two parts by a horizontal crack after compaction. Density test shows that the powder compaction occurred only in the upper part of the specimen. Brittle fracture was occurred during the bending test of the compact sample. Dispersion of shock energy due to spalling highly affected the bonding status of the nanocrystalline nickel powder.

• 동력기계공학회지
• /
• 제18권3호
• /
• pp.59-65
• /
• 2014

The computational fluid dynamics was carried out to evaluate turbulent models on the swirling flow of a gun-type gas burner(GTGB) according to the mesh size. The commercial SC/Tetra software was used for a steady-state, incompressible and three-dimensional numerical analysis. In consequence, the velocity magnitude from the exit of a GTGB and the flowrate predicted by the turbulent models of MP k-${\varepsilon}$, Realizable k-${\varepsilon}$ and RNG k-${\varepsilon}$ agree with the results measured by an experiment very well. Moreover, the turbulent kinetic energy predicted by the turbulent model of standard k-${\varepsilon}$ with mesh type C only agrees with the experimental result very well along the radial distance. On the other hand, the detailed prediction of the information of swirling flow field near the exit of a GTGB at least needs a CFD analysis using a fairly large-sized mesh such as a mesh type C.