• 대한음성학회:학술대회논문집
• /
• 대한음성학회 2003년도 10월 학술대회지
• /
• pp.101-104
• /
• 2003

In this paper, speech quality is improved by removing abrupt noise intervals and then substituting the gaps with estimates of the previous speech waveform. An abrupt noise detection signal has been proposed as a prediction error signal by utilizing LP coefficients of the previous frame. Abrupt noise intervals are estimated by using spectral energy. After removing estimated noise intervals, we applied several waveform substitution techniques such as zero substitution, previous frame repetition, pattern matching, and pitch waveform replication. To prove the validity of our algorithm, the LPC spectral distortion test and the recognition test are executed and, the results show that the speech quality is fairly well improved.

• 한국소음진동공학회논문집
• /
• 제22권10호
• /
• pp.959-967
• /
• 2012

The theory for a new electromagnetically biased diskless combined radial and axial magnetic bearing is developed. A typical magnetic bearing system is composed of two radial magnetic bearings and an axial magnetic bearing. The axial magnetic bearing with a large axial disk usually limits rotor dynamic performance and makes assembling and disassembling difficult for maintenance work. This paper proposes a novel electromagnet biased integrated radial-axial magnetic bearing without axial disk. This integrated magnetic bearing uses two axial coils to provide the bias flux to the radial and axial air gaps of the combined bearing. The axial magnetic bearing unit in this combined magnetic bearing utilizes reluctance forces developed in the non-uniform air gaps such that the axial disk can be removed from the bearing unit. The 4-pole homopolar type radial magnetic bearing unit is also designed and analyzed. Three dimensional finite element model for the bearing is also developed and analyzed to illustrate the diskless combined magnetic bearing.

• International Journal of Automotive Technology
• /
• 제5권3호
• /
• pp.209-213
• /
• 2004

The objective of this paper is to introduce the noise reduction characteristics of a double gap system, which is composed of two air-gaps and two partition sheets. The resonance of acoustic modes of an enclosed cavity can be effectively suppressed by installing the double gap system in the cavity. It is revealed from a simple, one-dimensional model that the double gap system is more effective than the single gap system that consists of one air-gap and one partition sheet, in that the former requires a smaller space than the latter. Finally, these theoretical conclusions are verified by comparison experiments using an actually manufactured enclosed cavity, of which the boundary surfaces are made of thick panels that can be assumed as rigid walls.

• 한국소음진동공학회논문집
• /
• 제14권6호
• /
• pp.528-535
• /
• 2004

Ultrasonic Vibrator is designed to achieve the maximum vibration amplitude at 30 kHz by in-cluding a horn (diameter, 40 mm), mechanical vibration amplifier at the top of the ultrasonic vibrator in the system and making the complete system resonate. In addition, it is experimentally visualized by particle imaging velocimetry (PIV) that the acoustic streaming velocity in the gap is at maximum when the gap between the ultrasonic vibrator and stationary plate agrees with the multiples of half-wavelength of the ultrasonic wave. This fact results from the resonance of the sound wave and the theoretical analysis of that is also accomplished and verified by experiment. It is observed that the magnitude of the acoustic streaming dependent upon the gap between the ultrasonic vibrator and stationary plate possibly changes due to the measurement of the average velocity fields of the acoustic streaming induced by the ultrasonic vibration at resonance and non-resonance. There exists extremely small average velocity at non-resonant gaps while the relatively large average velocity exists at resonant gaps compared with non-resonant gaps. It also reveals that there should be larger axial turbulent intensity at the hub region of the vibrator and at the edge of it in the resonant gap where the air streaming velocity is maximized and the flow phenomena is conspicuous than that at the other region. Because the variation of the acoustic streaming velocity at resonant gap is more distinctive than that at non-resonant gap, shear stress increases more in the resonant gap and is also maximized at the center region of the vibrator except the local position of center (r〓0). At the non-resonant gap there should be low values of vorticity distribution, but in contrast to the non-resonant gap, high and negative values of it exist at the center region of the vibrator with respect to the radial direction and in the vicinity of the middle region with respect to the axial direction. Acoustic streaming is noise-free due to the ultrasonic vibration and maintenance-free because of the absence of moving parts. Moreover, the proposed method by acoustic streaming can be utilized to the nano and micro-electro mechanical systems as a driving mechanism in addition to the augmentation of the streaming velocity.

• 한국철도학회논문집
• /
• 제15권3호
• /
• pp.231-236
• /
• 2012

본 논문에서는 고속철도의 주행 시 발생하는 공력소음에 대한 특성을 도출하는 연구를 수행하였다. 우선, 마이크로폰 어레이 시스템을 이용하여 고속철도 차량의 주행 소음을 측정을 통해서, 주요 공력소음원이 고속철도 차량의 전두부, 팬토그래프, 차간 부위임을 확인하였다. 또한 측정한 데이터를 바탕으로 빔형성 방법을 이용하여 빔출력을 구하였으며, 푸리에 변환을 통해서 주파수 영역에서의 빔파워 스펙트럼을 도출하였다. 본 연구를 통해서 고속철도의 주요 공력 소음원인 전두부, 팬토그래프, 차간 부위에 대한 음압 특성이 빔형성 방법을 이용하여 도출되었다.

• Journal of Welding and Joining
• /
• 제15권1호
• /
• pp.66-80
• /
• 1997

This paper describes a newly developed arc-sensing algorithm of seam-tracking for FCA W (flux-cored arc welding) horizontal fillet welding. In this algorithm, arc current and the Weighted-Are-Current (WAC) are used to adjust the position of a weld torch in directions of bead throat and weaving, respectively. The WAC, which is newly devised in this study, means that arc current in the vicinity of weaving end is more emphasized than that in the center of weaving. The reason of this is because there usually exists much noise in the center of weaving due to abrupt change of arc length in case some empty gaps exist in a fillet joint Variance analysis was performed in order to check the effect of weld parameters on arc current and the WAC. As a result, the relationships between tip-to-workpiece distance and arc current, and between weaving offset and the WAC were established.To check "the validity of the algorithm, seam-tracking experiments were performed ;mder various welding condition. The result of experiments showed a satisfactory tracking performance in the presence of empty gaps in a horizontal fillet joint.et joint.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 추계학술대회논문집
• /
• pp.1095-1100
• /
• 2003

Experimental studies on the aerodynamic coupling effect on natural frequencies, critical speed and flutter instability of DVD disks are investigated in this paper. The experimental results are compared with the theoretical analyses where the aerodynamic effects are represented in terms of elastic, lift and damping and stiffness components. The experiments are performed using a vacuum chamber and DVD disks rotating in vacuum, open and enclosure with several different gaps between disk and wall. The following three results are given. One is that the aerodynamic effect by the surrounding air reduces the natural frequencies and critical speeds of the vibration modes. The second is that natural frequency decreases as the disk-wall gap is decreased. Finally, it is shown that the disk vibration is reduced as the gap between the disk and the rigid wall decreases.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.163-169
• /
• 2005

A theoretical formulation on the forced acoustic response of an enclosed cavity having a double air-gap resonator on one of boundary panels of the cavity is developed in the paper. The double gap resonator consists of two air-gaps and two partition sheets as in the author's previous papers. This paper reveals that the double gap resonator reduces the level of a target noise peak by splitting the peak as two small peaks, and that it is more effective when it is designed so that the upper gap thickness is larger than the lower gap thickness under the constraint that the entire gap thickness is fixed as a constant value. Finally, verification experiments show that the theoretical formulation and analysis results are valid by comparing theoretical results with experimental ones.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.65-71
• /
• 2001

Absorbers such as porous materials and panels have limited absorption characteristics to some frequency bands. There is a need for absorbers with high absorption coefficients in a wide frequency ranges to make good response of room acoustics. This is almost impossible for a single absorption material. Composite absorption structure with cover, porous material. and air gap is known to have those wide frequency characteristics. In this basis. various composite absorption structures are measured and investigated as wide range absorption structures. Measurements are performed according to an international standard, ISO 354. Various surface types such as wooden slits, wood/steel perforated panels are selected as surface covers, and also various porous materials such as polyurethanes, polyesters, and glasswools are used inside the covers. Result shows that the area of void parts of surface materials is critical to high frequency absorptions, and thickness of air gaps are critical factor of the peak absorptions of low frequency bands.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.622-624
• /
• 2014

A maglev train records a host of physical variables such as gaps, voltages and currents for suspension control and monitoring purposes. These data available from a maglev contains wealth of information that can be explored for various uses. One possible of such application is to use the gap data to estimate the shape of the rail, especially at the joints where rails are connected. The eddy current sensors that measure the gap between the rail and the car body produce large peaks around the joints. The suspension controller discards these peaks. Since the shape of the peaks is related to the joint, however, these peaks can be utilized to estimate the shape of the joints. In this paper, we present preliminary results on estimating the joint shape using the peak data. The results show that the approach is promising, albeit several technical difficulties to overcome.