• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.121-122
• /
• 2007

Single crystal $CuAlSe_2$ layers were grown on thoroughly etched sem-insulating GaAs(l00) substrate at $410^{\circ}C$ with hot wall epitaxy (HWE) system by evaporating $CuAlSe_2$ source at $680^{\circ}C$. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of single crystal $CuAlSe_2$ thin films measured with Hall effect by van der Pauw method are $9.24{\times}l0^{16}\;cm^{-3}$ and $295\;cm^2/V{\cdot}s$ at 293K, respectively. The temperature dependence of the energy band gap of the $CuAlSe_2$ obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)\;=\;2.8382\;eV\;-\;(8.68\;{\times}\;10^{-4}\;eV/K)T^2/(T\;+\;155\;K)$.

• Progress in Medical Physics
• /
• v.35 no.1
• /
• pp.10-15
• /
• 2024

Purpose: This study aimed to comprehensively investigate the diverse characteristics of a novel commercial bolus, CLEANBOLUS-WHITE (CBW), to ascertain its suitability for clinical application. Methods: The evaluation of CBW encompassed both physical and biological assessments. Physical parameters such as mass density and shore hardness were measured alongside analyses of element composition. Biological evaluations included assessments for skin irritation and cytotoxicity. Dosimetric properties were examined by calculating surface dose and beam quality using a treatment planning system (TPS). Additionally, doses were measured at maximum and reference depths, and the results were compared with those obtained using a solid water phantom. The effect of air gap on dose measurement was also investigated by comparing measured doses on the RANDO phantom, under the bolus, with doses calculated from the TPS. Results: Biological evaluation confirmed that CBW is non-cytotoxic, nonirritant, and non-sensitizing. The bolus exhibited a mass density of 1.02 g/cm³ and 14 shore 00. Dosimetric evaluations revealed that using the 0.5 cm CBW resulted in less than a 1% difference compared to using the solid water phantom. Furthermore, beam quality calculations in the TPS indicated increased surface dose with the bolus. The air gap effect on dose measurement was deemed negligible, with a difference of approximately 1% between calculated and measured doses, aligning with measurement uncertainty. Conclusions: CBW demonstrates outstanding properties for clinical utilization. The dosimetric evaluation underscores a strong agreement between calculated and measured doses, validating its reliability in both planning and clinical settings.

• Nuclear Engineering and Technology
• /
• v.55 no.11
• /
• pp.4120-4124
• /
• 2023

High-level radioactive waste produced by nuclear power plants are disposed subterraneously utilizing an engineered barrier system (EBS). A gap inevitably exists between the disposal canisters and buffer materials, which may have a negative effect on the thermal transfer and water-blocking efficiency of the system. As few previous experimental works have quantified this effect, this study aimed to create an experimental model for investigating differences in the temperature changes of bentonite buffer in the presence and absence of air gaps between it and a surrounding stainless steel cell. Three test scenarios comprised an empty cell and cells partially or completely filled with bentonite. The temperature was measured inside the buffers and on the inner surface of their surrounding cells, which were artificially heated. The time required for the entire system to reach 100℃ was approximately 40% faster with no gap between the inner cell surface and the bentonite. This suggests that rock-buffer spaces should be filled in practice to ensure the rapid dissipation of heat from the buffer materials to their surroundings. However, it can be advantageous to retain buffer-canister gaps to lower the peak buffer temperature.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.373-376
• /
• 2004

The measurement of diffraction of LCOS microdisplay with various pixel size, interpixel gap, pixel height and coatings demonstrates that pixel size is the leading factor for diffraction loss, while the role of varying pixel gap is less significant comparatively. One-dimensional diffraction simulation is found to be in good agreement with the measurement. Noticeable deviation occurs when pixel size is as small as 8um.

• Proceedings of the KWS Conference
• /
• 1997.05a
• /
• pp.107-111
• /
• 1997

In this paper distribution of welding residual stress on the double fillet welded joint which exits and not exits root gap, i.e. full penetration and partial penetration is investigated by two dimensional cunduct and thermal elasto-plastic analysis. And stress distribution on notch-tip of the structure where welding residual stress regarded as initial stress and then external load is added is also investigated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.210-213
• /
• 1995

In this study,the effect of both process parameters (wheel velocity, friction coefficients between die and billet, etc) and die-shape (abutment height and shape, flash gap, etc.) on the surface defect on forming process is theoretically investigated. For this work, computer simulation was performed by using the DEFORM, a commercial FEM code. Through numerous simulations with different parameters and die shapes, We propose one optimal die shape for CONFORM process which can remove surface defect.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.33-38
• /
• 2000

In process of tube spinning far shock absorber on vehicles, the selection of feed rate and rounding radius of forming roller and revolution speed of tube and forming roller, forming gap between die and forming roller are very important factors to obtain the optimal process result. In this paper, rigid-plastic FEM and UBET analysis are applied to verify effect of each factors by forming load. We can obtain the optimal conditions to prevent defects during processing.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.1141-1146
• /
• 1993

The problem of tension control in metal-strip processing line is discussed. A new mathematical dynamic model which relates tension change, motor-speed change and roll-gap change is developed. Through the computer simulation of this model, parameter sensitivity, the tension transfer phenominon, and static and dynamic characteristics of strip tension were studied. Guidelines are developed to help one selecting locations of the master-speed drive in multi-drive speed control for tension adjustment and reducing the effect of interaction between tension and roll gap control.

• Korean Journal of Social Welfare Studies
• /
• v.41 no.2
• /
• pp.279-308
• /
• 2010

This study examines the association between family policies and family gap using data for 14 OECD countries. As family policies have different assumptions about women's roles and include variant sub-policies, this study identify two distinct family policies: 'employment support policy' to support women as employed workers and 'caregiving support policy' to support women as caregivers. Meanwhile, women's wage cannot be determined by the effect of 'only' family policy. Therefore, analysis model includes variant macro structure supposed to affect women's labor status and wage, like labor market structure, wage structure(compression), women's social status and economic status, and examines interaction effects between family policies and these labor market and social structures using Fuzzy-Set Qualitative Comparative Analysis (FSQCA). The FSQCA result shows that relatively low family gap is associated with the conjunctual causation of developed 'employment support policy' and compressed wage structure.

• The Journal of the Korea Contents Association
• /
• v.11 no.4
• /
• pp.273-282
• /
• 2011

This study was to investigate the effect of improve forelimb sensorimotor function and neurotrophic factor(GAP-43) expression when differing an application time of tDCS in ischemic brain injury rat model(pre, $1^{st}$, $7^{th}$, $14^{th}$). Focal ischemic brain injury was induced in 80 Sprague-Dawley rats through middle cerebral artery occlusion(MCAO) by 'Longa' method. And then experimental groups were randomly divided into four groups; GroupI: MCAO induction, GroupII: application of tDCS(10 min) after MCAO induction, GroupIII: application of tDCS(20 min) after MCAO induction, GroupIV: application of tDCS(30 min) after MCAO induction. Modified limb placing test and single pellet reaching test were performed to test forelimb sensorimotor function. And the histological examination was also observed through the immunohistochemistric response of GAP-43(growth-associated protein-43) in the cerebral cortex. In modified limb placing test, groupIII(p<0.05) showed significantly improve than the other groups on $14^{th}$). day. In single pellet reaching test, groupIII(p<0.01) and groupIV(p<0.05) significantly improved on $14^{th}$) day. And in immunohistochemistric response of GAP-43, group III showed significantly positive response than the other groups on $14^{th}$ day. These results suggest that the intensity(0.1 mA)/time(20 min) condition of tDCS application has a significant impact on the sensorimotor functional recovery in focal ischemic brain injury rat models.