• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.10
• /
• pp.1029-1038
• /
• 2009

This paper proposes a gain switching algorithm for joint position control of a hydraulic humanoid robot. Accurate position control of the lower body is one of the basic requirements for robust balance and walking control. Joint position control is more difficult for hydraulic robots than it is for electric robots because of an absence of reduction gear and better back-drivability of hydraulic joints. Backdrivability causes external forces and torques to have a large effect on the position of the joints. External ground reaction forces therefore prevent a simple proportional-derivative (PD) controller from realizing accurate and fast joint position control. We propose a state feedback controller for joint position control of the lower body, define three modes of state feedback gains, and switch the gains according to the Zero Moment Point (ZMP) and linear interpolation. Dynamic equations of hydraulic actuators were experimentally derived and applied to a robot simulator. Finally, the performance of the algorithm is evaluated with dynamic simulations.

• The Journal of Korea Robotics Society
• /
• v.17 no.2
• /
• pp.221-229
• /
• 2022

Sliding mode control (SMC) is a robust control method to control a robot arm with nonlinear properties. A high switching gain of SMC causes chattering problems, although the SMC allows the adequate control performance by giving high switching gain, without the exact robot model containing nonlinear and uncertainty terms. In order to solve this problem, SMC with sliding perturbation observer (SMCSPO) has been researched, where the method can reduce the chattering by compensating the perturbation, which is estimated by the observer, and then choosing a lower switching control gain of SMC. However, optimal gain tuning is necessary to get a better tracking performance and reducing a chattering. This paper proposes a method that the Q-learning automatically tunes the control gains of SMCSPO with an iterative operation. In this tuning method, the rewards of reinforcement learning (RL) are set minus tracking errors of states, and the action of RL is a change of control gain to maximize rewards whenever the iteration number of movements increases. The simple motion test for a 7-DOF robot arm was simulated in MATLAB program to prove this RL tuning algorithm. The simulation showed that this method can automatically tune the control gains for SMCSPO.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.379-382
• /
• 1996

Evolution Strategy is used as an effective search algorithm in optimization problems and Sliding Mode Control is well known as a robust control algorithm. In this paper, we propose a Sliding Mode Control Method for robot manipulator using Evolution Strategy. Evolution Strategy is used to estimate Sliding Mode Control Parameters such as sliding surface gradient, continuous function boundary layer, unknown plant parameters and switching gain. Experimental results show the proposed control scheme has accurate and robust performances with effective search ability.

• International Journal of Automotive Technology
• /
• v.8 no.3
• /
• pp.351-359
• /
• 2007

In this study, a hierarchical switching control scheme based on robust control theory is proposed for tracking control of vehicle longitudinal acceleration in the presence of large uncertainties. A model set consisting of four multiplicative-uncertainty models is set up, and its corresponding controller set is designed by the LMI approach, which can ensures the robust performance of the closed loop system under arbitray switching. Based on the model set and the controller set, a switching index function by estimating the system gain of the uncertainties between the plant and the nominal model is designed to determine when and which controller should be switched into the closed loop. After theoretical analyses, experiments have also been carried out to validate the proposed control algorithm. The results show that the control system has good performance of robust stability and tracking ability in the presence of large uncertainties. The response time is smaller than 1.5s and the max tracking error is about $0.05\;m/S^2$ with the step input.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.7
• /
• pp.582-588
• /
• 2001

The Multiple Model/Controller IMC(MMC-IMC) is a model-based control method which uses a set of model/controller pairs rather than a single model/controller to handle all possible operating conditions in the IMC control structure. During operation, one model/controller pair that best fit, for current plant situation is chosen by the switching algorithm. The major drawback of the switching controller is the bad transient performance due to the model error and the use fo linear controller for nonlinear plants. In this paper, we propose a method that transient response of the MMC-IMC using two recurrent neural networks. Simulation result shows that the proposed method represents better performance than the usual MMC-IMC`s.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.955-963
• /
• 2013

To acquire a performed and practical solution that is free from chattering, this study proposes the use of an adaptive super-twisting algorithm to drive a single-phase induction motor. Partial feedback linearization is applied before using a super-twisting algorithm to control the speed and stator currents. The load torque is considered an unknown but bounded disturbance. Therefore, a time-varying switching gain that does not require prior knowledge of the disturbance boundary is proposed. A simple sliding surface is formulated as the difference between the real and desired trajectories obtained from the indirect rotor flux oriented control strategy. To illustrate the effectiveness of the proposed control structure, an experimental setup around a digital signal processor (dS1104) is developed and several tests are performed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.1
• /
• pp.48-54
• /
• 2017

In this paper, hysteresis voltage control method is proposed to an unidirectional inverter control for piezoelectric load. Piezoelectric load has electrically RC characteristic, and is driven by the inverter to control the output voltage waveform. When controling the output waveform by PI control, appropriate gains need to be selected. However, hysteresis control may minimize the output distortion because it has maximum proportional gain. In addition, Hysteresis control algorithm has simple structure to realize and the response is fast. Although the switching frequency of the inverter by hysteresis control varies, the switching frequency for the piezoelectric load is lower than that by PI control for equivalent performance. In particular, on implementing the algorithm using FPGA, the algorithm can be implemented in fewer pabrics and the processing time can be reduced. The superiority of the proposed hysteresis voltage control was proved for piezoelectric load through simulation and experiment.

• Journal of Korean Institute of Industrial Engineers
• /
• v.25 no.4
• /
• pp.500-509
• /
• 1999

In this paper, we consider an optimal routing problem when point-to-point and point-to-multipoint connection traffics are offered in an ATM network. We propose a mathematical model for cost-minimizing configuration of a logical network for a given ATM-based BISDN. Our model is essentially identical to the previous one proposed by Kim(Kim, 1996) which finds a virtual-path configuration where the relevant gains obtainable from the ATM technology such as the statistical multiplexing gain and the switching/control cost-saving gain are optimally traded-off. Unlike the Kim's model, however, ours explicitly considers the VP's QoS(Quality of Service) for more efficient utilization of bandwidth. The problem is a large-scale, nonlinear, and mixed-integer problem. The proposed algorithm is based on the local linearization of equivalent-capacity functions and the relaxation of link capacity constraints. As a result, the problem can be decomposed into moderate-sized shortest path problems, Steiner arborescence problems, and LPs. This fact renders our algorithm a lot faster than the previous nonlinear programming algorithm while the solution quality is maintained, hence application to large-scale network problems.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.6
• /
• pp.1089-1094
• /
• 2016

In order to establish the robust controller design technique of series wound motor driver system. This paper proposes a method of Bang-Bang controller using a series wound motor driver system under improperly variable load. A Bang-Bang controller structure is simpler than the structure of PID plus Bang-Bang controller. This paper shows that a general 8 bits microprocessor is used efficiently implementing such an algorithm. The calculation time of software is extremely small when compared with conventional PID plus Bang-Bang controller. Both nonlinear operating characteristics of digital switching elements and describing function methods are used for the analysis and synthesis. Real time implementation of Bang-Bang controller is achieved. Concept design strategy of the control and PWM waveform generation algorithms are presented in the paper.

• ETRI Journal
• /
• v.31 no.2
• /
• pp.151-161
• /
• 2009

In this paper, we propose an adaptive multiview video coding scheme based on spatiotemporal correlation analyses using hierarchical B picture (AMVC-HBP) for the integrative encoding performances, including high compression efficiency, low complexity, fast random access, and view scalability, by integrating multiple prediction structures. We also propose an in-coding mode-switching algorithm that enables AMVC-HBP to adaptively select a better prediction structure in the encoding process without any additional complexity. Experimental results show that AMVC-HBP outperforms the previous multiview video coding scheme based on H.264/MPEG-4 AVC using the hierarchical B picture (MVC-HBP) on low complexity for 21.5%, on fast random access for about 20%, and on view scalability for 11% to 15% on average. In addition, distinct coding gain can be achieved by AMVC-HBP for dense and fast-moving sequences compared with MVC-HBP.