• Proceedings of the Korea Water Resources Association Conference
• /
• 2012.05a
• /
• pp.691-695
• /
• 2012

수위표의 영점에서 수면까지의 높이로 정의되는 해발수위는 유량 및 유사량 등과 같은 관련 수문자료를 생산하는데 기본이 되는 자료이며, 하천 및 수공구조물의 설계 등에 기초자료로 이용될 뿐만 아니라 수자원의 효율적인 관리 및 수문순환 해석을 위한 가장 중요한 기초자료로서 국가 차원의 올바른 수자원 계획과 정책을 수립하는데 널리 활용된다. 이와 같이 해발수위자료의 이용 분야가 다양하고 그 자체로서도 중요한 의미를 가지는 점을 고려할 때 무엇보다도 중요한 것은 자료의 품질이 확보되어야 하는 것이다. 그러나 영점표고검정수준점 및 기준 수위표의 설치 이후 오랜 시간이 경과됨에 따라 노후화와 수위관측소 주변의 환경변화가 발생하게 되어 자료의 정확도가 매우 낮아지고 있다. 본 연구에서는 해발수위 자료의 품질향상을 위해 수위관측소의 영점표고검정수준점 및 수위표 영점표고에 대하여 수준측량 및 RTK(Real Time Kinematic) GPS(Global Positioning System) 측량을 병행하여 수행하였으며, 조사측량된 값을 활용하여 기존에 측량된 영점표고검정수준점 및 수위표 영점표고에 대한 검토를 수행하였다. 금강 및 삽교천 수계에 위치한 50개 수위관측소 대하여 기존 측량값과 비교 검토한 결과 영점표고검정수준점은 0.10m 이하(54.0%), 0.10m 초과 ~ 0.50m 이하(26.0%), 0.50m 초과 ~ 1.00m 이하(6.0%), 1.00m초과 ~ 1.50m 이하(2.0%), 1.50m 초과 ~ 2.00m 이하(2.0%), 2.00m 초과 ~ 3.00m 이하(4.0%), 3.00m 초과(6.0%)의 값을 나타냈으며, 수위표 영점표고는 0.10m 이하(50.0%), 0.10m 초과 ~ 0.50m 이하(32.0%), 0.50m 초과 ~ 1.00m 이하(10.0%), 1.00m초과 ~ 1.50m 이하(2.0%), 1.50m 초과 ~ 2.00m 이하(2.0%), 2.00m 초과 ~ 3.00m 이하(2.0%), 3.00m 초과(2.0%)의 값을 가졌다. 이와 같이 기존과 금회 측량자료를 비교 검토한 결과 대부분이 안정적으로 유지되고 있으나 일부 수위관측소에서 변동량이 크게 발생한 원인은 영점표고검정수준점의 노후화, 기준 수위표의 교체 및 위치 변동, 인위적인 하천공사 등으로 인하여 발생한 것으로 판단된다.

• Korean Journal of Geomatics
• /
• v.3 no.1
• /
• pp.15-22
• /
• 2003

This study aims to construct a management system of road position information as part of the build-up to a maintenance and management system of highways. First, information on the positions of the roads were obtained by a real-time kinematic satellite surveying, and then the degree of accuracy was analyzed in comparison with the data of the existing design drawings. The linear coordinates of road center line obtained by using RTK GPS showed about 7.6-13.2cm errors in X and Y directions in the case of the national road No.2 section, and about 8.4-9.2cm errors in the case of local road No.1045 section. These errors were within the tolerance scope regulated by the TS survey, and could be practically used. In the case of vertical alignment, there were about 6.2cm errors in the Z direction in local road No.1045 section. Aerial photographs are normally used in producing numerical maps, and it can be practically used because the tolerance scope of the elevation control point is l0cm when the scale of aerial photographs is 1/1000. The management system of road position information, utilizing Object-Oriented Programming(OOP), was built having the data acquired in this way as the attribute data. The system developed in this way can enable us to spot the positions of road facilities, the target of management with ease, to easily update the data in case of changes in the positions of roads and road facilities, and to manage the positions of roads and road facilities more effectively.

• Korean Journal of Agricultural Science
• /
• v.42 no.1
• /
• pp.63-71
• /
• 2015

Path planning is an essential part for traveling and mowing of autonomous lawn mower tractors. Objectives of the paper were to analyze operation patterns by a skilled farmer, to extract and optimize waypoints, and to demonstrate generation of formatted planned path for autonomous lawn mower tractors. A 27-HP mower tractor was operated by a skilled farmer on grass fields. To measure tractor travel and operation characteristics, an RTK-GPS antenna with a 6-cm RMS error, an inertia motion sensing unit, a gyro compass, a wheel angle sensor, and a mower on/off sensor were mounted on the mower tractor, and all the data were collected at a 10-Hz rate. All the sensor data were transferred through a software program to show the status immediately on the notebook. Planned path was generated using the program parameter settings, mileage and time calculations, and the travel path was plotted using developed software. Based on the human operation patterns, path planning algorithm was suggested for autonomous mower tractor. Finally path generation was demonstrated in a formatted file and graphic display. After optimizing the path planning, a decrease in distance about 13% and saving of the working time about 30% was achieved. Field test data showed some overlap, especially in the turning areas. Results of the study would be useful to implement an autonomous mower tractor, but further research needs to improve the performance.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.1
• /
• pp.221-226
• /
• 2006

Around 2002, the United States Coast Guard (USCG) identified a need to re-capitalize their Reference Station (RS) and Integrity Monitor (IM) equipment used in the Nationwide Differential Global Position System (NDGPS). Commercially available off-the-shelf differential RS and IM equipment lacked the open architecture required to support long-term goals that include future system improvements such as use of new civil frequencies on L2 and L5 and realization of a higher rate NDGPS beacon data channel intended to support RTK. The first step in preparing for this future NDGPS was to port current RTCM SC-104 compatible RS and IM functionality onto an open architecture PC-based platform. Trimble's product Charisma is a PC-based RS and IM software designed to meet these USCG goals. In fact USCG engineers provided key designs and design insights throughout the development. We cannot overstate the contribution of the USCG engineers. Fundamental requirements for this effort were that it be sufficiently flexible in hardware and software design to support fluid growth and exploitation of new signals and technologies as they become available, yet remain backward compatible with legacy user receivers and existing site hardware and system architecture. These fundamental goals placed an implicit adaptability requirement on the design of the replacement RS and IM. Additionally, project engineers were to remain focused on sustaining the high level of differential GPS service that 1.5 million legacy users have come to depend on. This paper will present new hardware and software (i.e., Trimble's Charisma software) architecture for the next generation NDGPS RS and IM. This innovative approach to engineering on an open architecture PC-based platform allows the system to continue to fulfill legacy NDGPS system requirements and allows the USCG and others to pursue a scalable hardware re-capitalization strategy. We will use the USCG's recapitalization project to explain the essential role of the Charisma software.

• Journal of the Korean Society of Safety
• /
• v.33 no.3
• /
• pp.65-70
• /
• 2018

Terrain data for disaster analysis in hazardous or disaster areas is not only important but also needs to be built quickly. In particular, the introduction of drones is in the early stages of research using drones in a variety of fields such as shooting, analyzing and managing hazardous areas. It is expected that drone will be faster, safer and more effective than existing data collection method in case of small scale disaster hazard area and disaster area where equipment or manpower input is difficult. Therefore, in this study, drone shooting was performed for hazardous areas in mountainous roads located in Samcheok city, Gangwon province, and ground reference points were measured by RTK-GPS. The measured data were converted into DSM (Digital Surface Model) data by coordinate correction using Pix4D postprocessing program and then applied to the analysis of the hazard area of mountainous area. As a result, it was shown that it is effective to identify the risk by using the basic terrain data obtained from the drones.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2015.05a
• /
• pp.369-373
• /
• 2015

본 연구에서는 낙동강 강정고령보에서 달성보 구간에 대한 지속적 지형조사를 통해 다기능보 건설 및 운영으로 인한 하천지형의 변화양상과 정도를 파악하고자 하였다. 이를 위하여 4대강살리기사업 이전의 측량성과(낙동강하천기본계획, 2009년)를 기준으로 보 건설 및 하도정비 이후인 2013년과 2015년에 실측한 지형자료와 비교하였다. 2013년과 2015년 지형자료 취득은 대상구간(강정고령보~달성보: 23 km) 내 하도와 홍수터에 대해 각각 단일 및 다중빔 음향측심기와RTK-GPS 등의 측량장비를 이용하여 40 m 이상의 평면공간해상도를 가지도록 수행하였다. 대상구간 내 하천기본계획 지정 횡단측선에 대해 2013년과 2015년 지형정보를 비교함으로써 보 건설 및 하도정비로 인한 지형변화양상과 정도를 파악하고자 하였다. 특정 측선에서의 횡단지형자료인 2009년 측량성과와 비교하여 2013년과 2015년 실측자료는 전체 대상구간에 대한 3차원 공간정보를 제공함으로써 이들 간의 정성, 정량적 비교를 통하여 보 건설 및 운영을 통한 하도내 국부적 지형변화의 정도와 양상을 파악할 수 있었다. 이를 통해 하천의 지형학적, 수리학적 특성뿐만 아니라 보 건설 및 하도정비 등의 물리적 여건변화에 따른 특정 하천구간에 대한 시 공간적 지형변화특성을 파악할 수 있었으며, 이는 향후 하천관리 및 설계를 위한 연구와 실무에 널리 활용될 수 있을 것으로 기대된다.

• Journal of The Geomorphological Association of Korea
• /
• v.26 no.3
• /
• pp.31-42
• /
• 2019

The geomorphological changes of an unvegetated part of the Okjukdong coastal dune were analyzed between 2008 and 2018. Its natural landscape has been destroyed after artificial forestation, but there is no quantitative evidence on these changes. In this study, we measured the unvegetated area using a total station and a network RTK-GPS in 2008, 2014, and 2018. Using Krging method for the three point data sets, we constructed digital elevation models (DEMs) and analyzed topographic changes between the three years. The results showed that the sand of the study area decreased in volume from 2008 to 2014, because sand supply from the nearby beach was blocked by coastal forests. The sand volume temporarily increased from 2014 to 2018, because of the dune nourishment conducted in 2017. It seems that the upper part of the sand dune has shrunk, but the sand at the bottom has increased over the last decade.

• Journal of Drive and Control
• /
• v.21 no.1
• /
• pp.31-37
• /
• 2024

In this study, to prevent accidents in underground facilities during excavation, we developed a Lv.3 automated control system that can be configured as an electronic control system without changing the existing hydraulic system in a general excavator and utilized digital map information of underground facilities. We aimed to develop a strategy to prevent accidents caused by operator error. To implement this, a real-time excavator bucket end position recognition and control system was developed through angle measurement of the boom, arm, and bucket using an electronic joystick, RTK-GPS, and angle sensors. In addition, excavators are large, machine-based equipment, and it is difficult to control overshoot due to inertia with feedback control using position recognition information of the bucket tip. Therefore, feed-forward control is used to calculate the moving speed of the bucket tip in real-time to determine the target position. We developed a technology that can converge and verified the performance of the developed system through actual vehicle installation and field tests.

• Journal of the Korean earth science society
• /
• v.38 no.4
• /
• pp.251-262
• /
• 2017

The system of magnetic exploration with a drone flight was constructed and applied to the iron mine site. The magnetic probe system installed on the drone used a sensor as Bartington's fluxgate type magnetometer, Mag639 and the A/D converter to collect magnetic intensity values on the tablet PC. The drone flight control module is a highly expandable Pixhawk with allowing 15 minutes of flight by loading 3kg. Experiments on the magnetic field interference range were performed to remove the erroneous effect from the drone with applying RTK GPS to obtain the magnetic intensity value at the accurate position. The accurate location information enabled to obtain the gradient measurement of magnetic field by measuring twice at different altitudes. Also, by using the terrain information, we could eliminate the terrain effect by setting the flight path to fly along the terrain. These results are in line with the field experiments using the nuclear proton magnetometer G-858 of Geometrics Co., Ltd, which adds to the reliability of the drone based aeromagnetic survey system we constructed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.197-200
• /
• 2002

The current Inn technique is many problems that is permission of radio station using RF Wireless Modem, that is influence of geographic obstacle using radio wave, that is frequency interference, that is finiteness of frequency resources. In this paper, we are solved many elements, IM replaces RF Wireless Modem, we suggest transmission technique of correction message using mobile phone, we researched Interface Module development which is linkage of DGPS receiver and mobile phone. IM can transmit correction message passing RS-232 port and modem communication control. IM of base station is initialized RS-232 port and modem to move station for correction message transmission, IM waited response mode. IM of move station is initialized RS-232 port and modem, IM requests hand shaking to base station, completed connection establishment. Users are worked Differential surveying using receiving correction message between mobile phones.