• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.1
• /
• pp.11-21
• /
• 2020

This paper deals with the impact of a GNSS (Global Navigation Satellite System) antenna radome on the PCV (Phase Center Variations) and the estimated kinematic coordinates. For the Trimble and Leica antennas, specially set up CORS (Continuously Operation Reference Stations) in Korea, the PCC (Phase Center Corrections) were calculated and compared for NONE, SCIS, SCIT, and TZGD radome from the PCV model published by the IGS (International GNSS Services). The results revealed that the PCC differences compared to the NONE were limited to about 1mm in the horizontal component while those of the vertical direction ranged from a few millimeters to a maximum of 7mm. Among the radomes of which PCV were compared, the SCIT had the most significant influence on the vertical component, and its GPS (Global Positioning System) L2 and L2 PCC (Phase Center Corrections) had opposite direction. As a result of comparing the kinematic coordinates estimated by the baseline processing of 7 CORSs with an application of the PCV models of the various radomes, the SCIS which was actually installed at CORS in Korea showed 3.4mm bias, the most substantial impact on the ellipsoidal height estimation whereas the SCIT model resulted in relatively small biases.

• Journal of Advanced Navigation Technology
• /
• v.24 no.4
• /
• pp.273-279
• /
• 2020

In the Korea's SBAS(KASS), reference site is an important infrastructure facility for the collecting and monitoring GPS/GEO signals. The SBAS reference station has an clear requirements than other regular monitoring stations. It requires constant maintenance during the system operation. The development for KRS site should be prepared for site survey, site construction, antenna geodetic survey, equipment installation and operation. Site survey is initially performed as an important step to predict site availability and system performance. The operation center must provide the reference site, equipment room, and appurtenant to satisfy the site requirements. The position of antennas is very important information, and accuracy must be secured through the geodetic survey. Measurement collected at the from precise antenna are provided to the KASS processing station. The position of antenna should be maintained through continuous position checks and updates during the operation. When the development of the KRS site is completed, it performs tasks for installing and operating the KRS equipment. In this paper, we presented the procedures and some results for the development of the 7 KRS sites.

• Journal of the Korean earth science society
• /
• v.40 no.1
• /
• pp.37-45
• /
• 2019

In spite of continued nourishments, Haeundae Beach in Busan has been suffering from erosion, this being caused by the increased wave energy due to global warming and intermittent typhoon reported by previous works. In the meantime, the typhoon Chaba hit Basan in October 2016. In order to investigate the effects of the typhoon in beach erosion and how fast the beach recovered after the typhoon, repeated beach profiling using a VRS-GPS system was carried out, and the grain size analyses for surface sediments sampled on the beach were conducted. Immediately after the typhoon invasion, Haeundae beach was eroded by 1.4 m in average height. The mean high tide lines were retreated back by 12 m, and beach slope became gentler from $3.8^{\circ}$ to $1.7^{\circ}$. The mean grain sizes of surface sediments became coarser from $1.6{\Phi}$ to $1.2{\Phi}$ after two months, and the sorting well sorted. After two months of typhoon landfall, the mean high tide lines have recovered by 85%, and the beach topography almost recovered. This suggests that the impact of typhoons on Haeundae beach erosion is negligible, and the relaxation time is shorter than that of other beaches.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.337-343
• /
• 2004

Spatial information could be obtained from spaceborne high resolution optical and synthetic aperture radar(SAR) images. However, some satellite images do not provide physical sensor information instead, rational polynomial coefficients(RPC) are available. The objectives of this study are: (1) 3-dimensional ground coordinates were computed by applying rational function model(RFM) with the RPC for the stereo pair of Ikonos images and their accuracy was evaluated. (2) Interferometric SAR(InSAR) was applied to JERS-1 images to generate DEM and its accuracy was analysis. (3) Quality of the DEM generated automatically also analyzed for different types of terrain in the study site. The overall accuracy was evaluated by comparing with GPS surveying data. The height offset in the RPC was corrected by estimating bias. In consequence, the accuracy was improved. Accuracy of the DEMs generated from InSAR with different selection of GCP was analyzed. In case of the Ikonos images, the results show that the overall RMSE was 0.23327", 0.l1625" and 13.70m in latitude, longitude and height, respectively. The height accuracy was improved after correcting the height offset in the RPC. i.e., RMSE of the height was 1.02m. As for the SAR image, RMSE of the height was 10.50m with optimal selection of GCP. For the different terrain types, the RMSE of the height for urban, forest and flat area was 23.65m, 8.54m, 0.99m, respectively for Ikonos image while the corresponding RMSE was 13.82m, 18.34m, 10.88m, respectively lot SAR image.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2002.04a
• /
• pp.17-24
• /
• 2002

Mechanization is the characteristic of the industrial era and computerization is the characteristic of the Information Era. Now we are facing on the transition from Industrial Era to information Era. Established the National Geo-spatial Data Infrastructures is the fundamental base for information society and is one part of the national basic economic development plan. From 1980's China started his successful transition from traditional methods to high-tech based mapping. China has laid out a high accuracy national GPS (global Positioning System) network, and completed the geographic information databases for scale of 1:1million and 1:250,000. Now it is working on the databases for scales of 1:50,000 and 1:10,000, the world highest level. The massive national programmed has been dubbed "Digital China," since it involves massive quantities of digitized geographical information. Simultaneity, GIS technology and the geo-spatial data have been used widely in electronic government affair, environmental protection, disaster control, ITS and etc. The users have realized the benefits more and more widely. Internet is an efficient way to distribute the geo-information, the State Bureau of Surveying and Mapping has give great effort to settle down the rules and standards to establish the clearing house. Some National Geo-standards have issued, and some of them are on the way. The GIS software is another important factor in the GIS industry. Chinese government working-out some good policy to supports the GIS software developer to have their own copyright. This paper is based on the above to introduce the status and development of Geomatics in China. in China.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.31 no.6_2
• /
• pp.567-576
• /
• 2013

The determination of the geoid in South Korea is a national imperative for the modernization of height datums, specifically the orthometric height and the dynamic height, that are used to monitor hydrological systems and environments with accuracy and easy revision, if necessary. The geometric heights above a reference ellipsoid, routinely obtained by GPS, lead immediately to vertical control with respect to the geoid for hydrological purposes if the geoid height above the ellipsoid is known accurately. The geoid height is determined from gravimetric data, traditionally ground data, but in recent times also from airborne data. This paper illustrates the basic concepts for combining these two types of data and gives a preliminary performance assessment of either set or their combination for the determination of the geoid in South Korea. It is shown that the most critical aspect of the combination is the gravitational effect of the topographic masses above the geoid, which, if not properly taken into account, introduces a significant bias of about 8 mgal in the gravity anomalies, and which can lead to geoid height bias errors of up to 10 cm. It is further confirmed and concluded that achieving better than 5 cm precision in geoid heights from gravimetry remains a challenge that can be surmounted only with the proper combination of terrestrial and airborne data, thus realizing higher data resolution over most of South Korea than currently available solely from the airborne data.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2006.04a
• /
• pp.485-490
• /
• 2006

In this study, the Digital Surface Models of various spatial resolutions were constructed using LIDAR point data on Digital Photogrammetric System. Then, the accuracies of each DSM's were evaluated using GPS surveying data. And also, observable features were classified and their accuracies were evaluated to verify the availability for Ground Control Point. On Socet Set, Digial Photogrametric System 5 DSM's of which spatial resolutions were 0.15m, 0.5m, 1.0m, 2.5m and 5.0m were constructed and the accuracies of eahc DSM's evaluated in RMSE. The RMSE's of each DSM's were 0.03m, 0.05m, 0.08m, 0.12m and 0,19m. The building feature was observable in DSM's of which spatial resolutions were 0.15m, 0.30m and 0.50m. On the contrary, it could hardly be observed in those of other spatial resolutions. In comparison with the digital map at the scale of 1:1,000, the DSM at the spatial resolution of 0.lim was shifted horizaltally by 0.6m-0.7m of RMSE in each X, Y direction. Therefore, GCP of which horizontal RMSE is better than 1m can be obtained from the DSM at the spatial resolution of 0.15m, of which vertical RMSE is 0.03m-0.19m as the RMSE of DSM. This point cannot be used in aerial triangulation of cartography but can be used for GCP in modeling of satellite image at the moderate resolution.

• Korean Journal of Remote Sensing
• /
• v.29 no.5
• /
• pp.477-486
• /
• 2013

To analyze tendency of temporal and spatial change of shorelines and to estimate rate of shoreline changes using long-term shoreline change data is very important for the coastal environmental management. In this study, investigation was conducted to estimate the rate of shoreline changes using long-term shoreline change data from the year 1985 to 2009 aerial photographs. In this process aerial triangulation, GPS surveying and digital mapping was done for the estimation of changes. As the results, shorelines of Bangpo and Kkotji Beach retreated at a maximum rate of 0.2 m/yr and 0.8 m/yr, respectively. The shoreline could be changed by various factors. However, it was presumed that coastal erosion has been mainly affected by retaining wall constructed in the late 1990s.

• Proceedings of the Korea Contents Association Conference
• /
• 2007.11a
• /
• pp.27-29
• /
• 2007

The visual implementation of 3-dimensional national environment is focused by the requirement and importance in the fields such as, national development plan, telecommunication facility deployment plan, railway construction, construction engineering, spatial city development, safety and disaster prevention engineering. The currently used DEM system using contour lines, which embodies national geographic information based on the 2-D digital maps and facility information has limitation in implementation in reproducing the 3-D spatial city. Moreover, this method often neglects the altitude of the rail way infrastructure which has narrow width and long length. There it is needed to apply laser measurement technique in the spatial target object to obtain accuracy. Currently, the LiDAR data which combines the laser measurement skill and GPS has been introduced to obtain high resolution accuracy in the altitude measurement. In this paper, we first investigate the LiDAR based researches in advanced foreign countries, then we propose data a generation scheme and an algorithm for the optimal manage and synthesis of railway facility system in our 3-D spatial terrain information. For this object, LiDAR based height data transformed to DEM, and the realtime unification of the vector via digital image mapping and raster via exactness evaluation is transformed to make it possible to trace the model of generated 3-dimensional railway model with long distance for 3D tract model generation.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.34 no.2
• /
• pp.185-194
• /
• 2016

The purpose of this study is to present a method to provide environment information based on spatial information document. At present, a lot of spatial information, including environment information, is being produced, but separate software or system is required for the user to acquire the information. In particular, in the case of environment information, various types of information are being produced, such as ecology, vegetation and measurement network data. Therefore, it is necessary to present the form and the making method of spatial information document that allows using environment information as spatial information without separate software or system. To provide spatial information document-based environment information, types and forms of environment information, data format and offering methods produced by the government, in particular, the Ministry of Environment and the local governments, are analyzed. 12 fields are classified and the form of produced data is GIS DB, measurement network data, text data and so on. With decrease of paper maps, spatial information document that offers display by layer, coordinate data, attribute data, distance and area measurement, location search by coordinates, GPS location linkage and location display on the map is presented to increase utilization of geo-environment information maps. Finally, the standard document specification based on spatial information document is presented in consideration of usability and readability in order to provide a variety of environment information without separate software or system.