• Journal of the Korean Magnetics Society
• /
• v.13 no.6
• /
• pp.221-225
• /
• 2003

Effects of annealing temperature on the crystalline and magnetic properties of YIG films grown by solid phase epitaxy. The eptiaxy films were made by annealing Fe-Y-O amorphous films in the air at 550-1050 $^{\circ}C$ which were sputtered on GGG (111) substrates in a conventional rf sputtering system. Crystallization temperature of Fe-Y-O amorphous films on GGG (111) substrate was between 600 and 650 $^{\circ}C$ which is much lower than that Fe-Y-O powder prepared by sol-gel method. Excellent epitaxial growth of YIG films could be conformed by the facts that the diffraction intensity of YIG (888) plane was comparable with that of GGG (888) plane and full width at half maximum of YIG (888) rocking curve was smaller than 0.14$^{\circ}$ when films were annealed at 1050 $^{\circ}C$. It could be seen that it is necessary to anneal the films at higher temperature for an excellent epitaxy because lattice parameter of YIG films were smaller and the peak of YIG (888) plane is higher and narrower with increasing annealing temperature. Films annealed at higher temperature shows M-H loop with perpendicular anisotropy which was due to 0.15％ lattice mismatch between YIG and GGG.

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.293-300
• /
• 1999

고주파 마그네트론 스퍼터법을 이용한 YIG(yttrium iron garnet)박막 제조시 기판유형, 기판온도, 스퍼터전력, 스퍼터가스 등의 증착변수와 증착후 열처리 조건이 YIG 박막의 결정성, 화학조성, 미세구조 그리고 자기적 특성에 미치는 영향에 대하여 고찰하였다. 75$0^{\circ}C$ 이상의 온도에서 수행한 증착후 열처리에 의하여 비정질 박막이 결정화되었으며, 특히 GGG(gadolinium gallium garnet)기판 위에 제조된 박막은 강한 (111)우선배향성을 나타냈다. 박막조성은 스퍼터가스 내의 산소분율에 민감하게 영향을 받았으며, 산소분율이 20%인 스퍼터가스를 사용하여 제조된 박막은 Y2.88Fe3.84O12의 조성을 나타내었다. 증착후 열처리 온도가 90$0^{\circ}C$로부터 110$0^{\circ}C$로 증가함에 따라, GGG 기판위의 박막의 표면거칠기는 2.5nm에서 40nm로 증가하였으며, 보자력과 강자성 공명 선폭은 감소하였다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.7
• /
• pp.1168-1175
• /
• 2000

To observe propagation characteristics of microstrip lines on YIG film, the FDTD is employed. For various GGG substrate and YIG film, the dispersion curves and the bandwidth of the cutoff region are calculated. And the distribution of the electric fields of the transverse plane underneath the conductor strip is obtained near upper and lower cutoff frequency. The results of two and three dimensional FDTD for the upper cutoff frequency are compared with spectral domain approach(SDA). A good agreement is verified, although there is relative error 6% between the results calculated by the two methods.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.325-329
• /
• 2002

This study targets mainly to reduce the manufacturing costs of cam spindles and manufacturing of mechanical components with longer service durations through application of surface engineering techniques on cam spindles. Within the frame of this study, we have attempted to establish the performances of cam spindles manufacture from forged steel and SGCI, through performance of wear tests in plate-disk system, metalographic investigations, SEM imaging, EDS analyses and micro hardness scans on test samples having the same sizes with original cam that once obtained from casting of Spherical Graphite Cast Iron (SGCI) are subjected partially to Boronising and partially to hardening in a salt solution and cam spindles currently manufactured from CK 45 through cauterization based reshaping.

• Journal of the Korean Magnetics Society
• /
• v.10 no.3
• /
• pp.123-132
• /
• 2000

Cerium substituted YIG thin films were grown by rf magnetron sputter techniques. We investigated the effects of post-deposition heat-treatment as well as various deposition parameters such as substrate materials, substrate temperature. sputter power, and sputter gas types on the crystallinity, chemical composition, microstructure and magnetic characteristics of the films. Post-deposition heat treatment over 750 $\^{C}$ was applied to crystallize as-prepared amorphous films, and a strong tendency of particular crystallographic planes tying parallel to substrate surface was observed for the post-deposition heat-treated films on GGG substrate. The chemical composition of the films exhibited a wide range of chemical stoichiometry depending on the oxygen fraction of sputter gas, and in particular the composition of the film deposited in sputter gas with an oxygen fraction of R = 10% was Ce$\_$0.23/Y$\_$1.30/Fe$\_$3.50/O$\_$12/. With raising the temperature of post-deposition heat-treatment from 900 $\^{C}$ to 1100 $\^{C}$, the surface roughness of the film on GGG substrates increased from about 3 nm to 40 nm, but their coercive force and ferromagnetic resonance line width decreased from 0.477 kA/m to 0.369 kA/m and from 12.5 kA/m to 8.36 kA/m, respectively.

• Korean Journal of Crystallography
• /
• v.4 no.1
• /
• pp.1-5
• /
• 1993

The crystal structure of N-(2'-chloro-4'-vitrophenyl)-5-chlorosalicylamide( Niclosamide ) monohydrate has been determined from 1976 sig- nificant independent reflections collected on an automated CAD4 diffractometer using graphitemonochromated Mo-Ka radiation. The crystal is monoclinic, space group P211c, with unit cell dimensions, a=11.331 (3), b=16.964(2), c=7.347(4)A , P =98.20(3)° and Z=4 at T=293k. The structure was solved by direct method using seminvariants of ggg Parity group and refined by the full-matrix least-square method, resulting model with reliability factor, R=0.046. The feature of the molecule show planar structure in parallel to the ab crystal plane.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2003.06a
• /
• pp.192-193
• /
• 2003

YIG 에피택시박막은 다른 강자성, 페리자성재료에 비해 수 GHz의 영역에서 매우 우수한 특성을 나타내고 있다. YIG 에피택시 박막은 고상에피택시 방법으로 제조할 경우 매우 편리하게 제조할 수 있는 것으로 알려져 있는데, 이 방법은 상온에서 Y-Fe-O 박막을 GGG(111)기판에 스파터한 뒤 공기 중에서 열처리하면 간편하게 얻을 수 있다. 이 방법은 통상과 같이 고온에서 아주 느린 속도로 에피택시박막을 성장시키는 스파터방법에 비해 매우 간편하고 경제적인 것으로, 본 연구에서는 보통의 분말소결공정으로 제작된 2.5인치 YIG 타겟을 사용하여 두께 2.5 $\mu\textrm{m}$ 비정질 Fe-Y-O 박막을 만든 뒤 550 - 1050 $^{\circ}C$의 공기 중에서 열처리하였다. 비정질 박막을 $600^{\circ}C$이하에서 10 시간동안 열처리하였을 경우 매우 약한 YIG상의 회절선만 관찰할 수 있었다. 반면에 온도를 $650^{\circ}C$로 올리면 매우 강한 (444) 또는 (888)회절선과 매우 약한 다른 회절선을 관찰 할 수 있었다. 이 시편의 경우 (888)회절선의 강도는 GGG기판의 (888)회절선의 강도와 비교할 정도로 매우 강하여 에피택시성장이 매우 잘 이루어질 수 있다는 가능성을 확인할 수 있었다. 그리고 YIG(888) 회절선의 록킹곡선의 반가폭이 0.14$^{\circ}$ 이었고, 이것은 에피택시성장이 매우 잘 이루어지고 있음을 의미하는 것이다. 열처리 온도가 감소함에 따라 YIG박막의 격자상수는 감소하였으며 YIG(888)회절선의 강도는 그림 1과 같이 넓어지고 그 강도는 약해진다.

• Journal of the Korean Magnetics Society
• /
• v.13 no.1
• /
• pp.36-40
• /
• 2003

We have grown D $y_{x}$B $i_{3-x}$F $e_{5}$ $O_{12}$ (x = 0.5,1.0, 1.5,2.0) magnetic garnet thin films upon $Al_2$O3i and GGG substrate using Pechini process. The annealing temperature to get single phase D $y_{x}$B $i_{3-x}$F $e_{5}$ $O_{12}$ garnet is dependent on substrate, i.e. the annealing temperature for GGG substrate il 5$0^{\circ}C$ lower than that for $Al_2$ $O_3$ substrate. The grains of garnet thin film grown on GGG (111) plane align along [111] direction, and in this case the hysteresis curve does not saturate up to H : 5000 Oe. We attribute this phenomenon to rotation magnetization process. The maximum amount of Bi substitution in polycrystalline D $y_{x}$B $i_{3-x}$F $e_{5}$ $O_{12}$ thin film prepared by Pechini process is restricted to 2.0 Bi atom/unit cell, and this value is less than that in single garnet crystall grown by LPE method.own by LPE method.ethod.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2000.09a
• /
• pp.423-424
• /
• 2000

• The Korean Journal of Mycology
• /
• v.23 no.3 s.74
• /
• pp.202-208
• /
• 1995

This study describes the effects of several components on PCR amplification used for RAPD. We used different concentrations of reaction components to obtaine discrete and reproducible PCR products from Pleurotus cornucopiae. The optimum concentrations of reaction components were found to be 80 ng of template DNA, 30 pmole of 10-mer primer, $200\;{\mu}M$ dNTP, 2mM $MgCl_2$, 50 mM KCl, 10 mM Tris-HCl(pH 9.0), 0.1% Triton X-100, 1.5 unit of Taq DNA polymerase (promega) in $50\;{\mu}l$ reaction volume. The optimum annealing temperature was $35^{\circ}C$. These results proved to be valuable for characterization of Pleurotus spp.