• 한국세라믹학회지
• /
• 제18권1호
• /
• pp.3-12
• /
• 1981

A glass-ceramics based on blast-furnace slag, with some additives to the theoretical composition in order to control properties of mother glass and the heat treatment conditions, has been investigated. The raw materials in this study were blast-furnace slag, serpentine, feldspar and quartz as mother glass ingredients. Titanium dioxide and chromite were used as the nucleating agents. Batch compositions of the prepared glasses and ceraming conditions were found by trial and error method. The optimum conditions were confirmed by analyzing several measured physical properties such as density change during heat treatment, microhardness of slag-ceramics prepared, viscosity change of glass at heat treatment temperatures, nucleation density change, dilatometric properties, differential thermal analysis, identification of the grown crystal and crystal sizes. The batch composition feasible to prepare slag-ceramics was 40% of blast-furnace slag, 25% of serpentine, 18% of feldspar and 17% of silica sand. Three percent titanium dioxide and 1% chromite of the mother glass were added as nucleating agents. The ceraming conditions under which the slag-ceramics having considerably good properties can be developed found as: "The glass was heated at 75$0^{\circ}C$ for 2 hours for nucleation, and the temperature was raised up to 1, 00$0^{\circ}C$ with a rate of 0.75$^{\circ}C$/min for crystal growth.owth.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표회 논문집(I)
• /
• pp.54-59
• /
• 1998

This experimental Study presents the flow properties of mortar Using the Blast-furnace Slag Sand. It gives following result. The substitution rate is inversely proportional to flow. But W/C ratio is directly proportional to flow. Consequently Flow characteristics of the Blast-furnace mortar is simillar to the river sand mortar.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.589-594
• /
• 2011

Raw mix of molten clinker was fabricated using blast furnace slag as starting material. Raw mix was melted at 1620$^{\circ}C$ for molten clinker fabrication. It was found that molten clinker contained alite and belite equivalent to OPC clinker mineral by optical microscope and SEM. The size of alite was 10~50 ${\mu}m$ and that of belite was 20~80 ${\mu}m$. This result thought to be attributed low $Al_2O_3$ content and cooling condition. Interstitial phase increased with blast furnace slag content and gehlenite was formed by the condition of LSF and SM. So raw mix with 27~41% blast furnace slag could be converted into cement clinker by appropriate choice of melting andcooling methods in this study.

• 한국농공학회논문집
• /
• 제50권5호
• /
• pp.19-27
• /
• 2008

This study was performed to evaluate the compressive strength and acid-resistant of polymer concrete using redispersible polymer powder(RPP) and blast furnace slag powder(BSP). Material used were ordinary portlant cement, recycled coarse aggregate, natural fine aggregate, redispersible polymer powder and blast furnace slag powder. The main experimental variables were the substitution ratio of redispersible polymer powder and blast furnace slag powder, when the substitution ratios of RPP were 0, 1, 2, 3, 4, 5 and 6%, and those of BSP were 10%. The compressive strength and acid-resistant of polymer concrete using RPP and BSP were compared with those of ordinary concrete(Basis). When the substitution ratio of RPP was 1%, at age of 28 days, the compressive strength were more higher than those of Basis by 24%, and it was decreased with increasing the RPP content, respectively. Also, the water absorption ratio was decreased with increasing the RPP content. But, the acid-resistant was improved with increasing the RPP content.

• 대한건축학회논문집:구조계
• /
• 제33권12호
• /
• pp.63-70
• /
• 2017

When industrial by-products like slag and fly ash are using in concrete with cement, it improves strength and durability against external deterioration factors by densifying the structure through potential hydraulic and pozzolanic reaction. But it has been pointed out that high dependence on the quality variation and the curing condition using a admixure material for concrete. In this study, the characteristics of internal micropore structure according to curing condition were analyzed for pastes and mortar specimens under using blast furnace slag powder. As a result, the variation of compressive strength and the internal microstructure were observed according to curing conditions by binder type. Particularly, using blast furnace slag powder, decrease in compressive strength were clearly observed in indoor and carbonation curing compared with water curing. The pore structure analysis also clearly observed the decrease of the gel pore existing in the CSH hydrate layer and the increase of the capillary pore in indoor and carbonation curing compared with water curing condition.

• 한국건축시공학회지
• /
• 제3권3호
• /
• pp.127-133
• /
• 2003

Carbonation and drying shrinkage are very important properties of concrete, that can cause concrete to lower its capacity and spall. But the research on them in high strength concrete is very poor. In this study, to estimate influences of W/B, the kind of admixture, the replacement ratio of admixture, fineness of blast furnace and etc. on drying shrinkage and carbonation, we make experiment with 3 levels(28, 35, 55%) of W/B, 3 kinds(blast-furnace slag, fly-ash, silica-fume) of admixture, 3 levels of the replacement ratio, 3 levels(4000, 6000, 8000cm2/g) of fineness of blast-furnace slag and 2 kinds of curing condition. As the results, compressive strength of concrete was decreased, as W/C was increased and the replacement ratio of admixture was increased. Drying shrinkage was increased, as W/B was higher, the replacement ratio of admixture was increased and fineness of blast-furnace slag was decreased. And carbonation was increased, as W/B ratio was higher, the replacement ratio of admixture was increased.

• 자원리싸이클링
• /
• 제33권2호
• /
• pp.46-53
• /
• 2024

전기로 제강공정에서 연속주조 조업 완료 후 ladle에 잔존하는 슬래그의 헌열과 슬래그 중 잔존 CaO를 활용하기 위해 전기로 출강 후 ladle 상부에 슬래그를 투입하여 Ladle Furnace(LF) 공정에서의 전력과 생석회의 사용량을 저감하는 공정이 연구되어 산업현장에서 활용되고 있다. 하지만 이러한 공정은 LF 공정과 연속주조 공정상 시점이 맞지 않으면 재활용율이 낮아진다. 슬래그 재활용율을 높이기 위해서 시점이 맞지 않는 경우 ladle의 슬래그를 슬래그 포트에 미리 부은 후 재활용하는 방법에 대해서 LF 조업 영향성을 분석하였다. Ladle 용융 슬래그를 재활용 방법에 대해 열역학 프로그램 Factsage 8.3에서 FSsteel(steel database)와 FToxid(oxide database)를 활용하여 슬래그 조성에 대한 액상화율을 계산하였고, 재활용 방법에 따라 각 10heats 조업 적용을 통해 슬래그 중 탈황능과 LF 조업성에 대해서 비교하였다. 그 결과 연속주조 조업 완료 후 바로 ladle에 슬래그를 재활용하는 방법에서 전력 사용량이 0.3MWh 낮고, LF 조업시간은 1.2분 단축되었으며, 탈황율은 5.8% 높은 결과를 얻었다.

• 토지주택연구
• /
• 제3권3호
• /
• pp.287-297
• /
• 2012

보통포틀랜드시멘트(OPC)와 고로슬래그 및 플라이애시 만으로 설계기준압축강도 80MPa의 3성분계 고강도콘크리트(이하 고강도콘크리트)를 개발하기 위하여, 고로슬래그와 플라이애시의 대체율이 고강도콘크리트의 경화전 후 재료물성 변화에 미치는 영향을 평가하였다. 고강도콘크리트의 경화전후 재료물성 평가결과, 고로슬래그와 플라이애시 대체율이 최대 30%까지 증가할수록 유동성과 장기강도가 우수한 것으로 나타났다. 또한 OPC만으로 제작된 시험체와 비교하여 길이변화 특성이 우수하며, 혼화재 사용에 따른 탄산화는 없는 것으로 나타났다. 고강도콘크리트 재료물성 평가결과, 고로슬래그 대체율 25%, 플라이애시 대체율 15%일 경우, 경화전 후 재료물성이 가장 우수한 것으로 나타났다. 이 연구결과는 향후 고가의 실리카퓸을 대체할 수 있는 고강도콘크리트의 개발에 유용하게 활용될 수 있을 것으로 기대된다.

• 한국안전학회지
• /
• 제27권2호
• /
• pp.25-32
• /
• 2012

In this study, the effect of blast furnace slag on precast concrete culvert was assessed by measuring the flexural strength using to full scaled box culvert. As a result, the initial cracking load and yield load of reinforced concrete box converts are increased in comparison with those of the normal concrete box culvert, but the ultimate load is decreased slightly. It can be concluded that use of blast furnace slag induce to flexural strength in precast concrete box culvert greatly improved the serviceability.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.687-690
• /
• 2005

Recently, to consider financial and constructive aspect, usage of Admixture, like Blast- Furnace Slag and Fly-Ash, are increased. These mineral admixtures, a by-product of steel industry, have many advantage, to reduce the heat of hydration, increase in ultimate strength, improve workability and etc. But it also reduces early-age strength, so it is prevented from using of Blast-Furnace Slag at cold-weather-concrete. In this study, for the purpose of increasing usage of mineral admixtures, like Blast-Furnace Slag and Fly ash, it is investigated the strength properties of concrete subjected to under low temperature According to this study, if early curing is carried out before having frost damage, the strength of concrete, subjected to frost damage, is recovered. And to consider increasing effect of strength, it is more effective to use of mineral admixtures, especially to use blast furance slag.