• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.27-34
• /
• 2001

A new functionally gradient metal coating method using an atomic mixing technique was developed. In this work the effect of silver atomic mixing on the tribological characteristics of silver$.$ films. has been investigated experimentally. Atomic mixing was implemented by using the, bombardment .of accelerated Ar ions during the thermal evaporation coating process of silver films. Experiments were performed in dry conditions using a ball-on-disk test rig at a load range of 19.6 mN - 17.64 N and a sliding velocity of 20 mm/sec. Results showed that the life of functionally gradient silver coating was enhanced about 100 times more than that of thermally evaporated silver coating and 2 times more than that of IBAD silver coating. The functionally gradient. film also showed low friction and wear compared to those of the evaporated silver and

• 한국해양공학회지
• /
• 제13권1호통권31호
• /
• pp.62-69
• /
• 1999

67Ni-22Cr-10Al-1Y and $ZrO_2-8Y_2O_3$ were coated on the substrate surface of ST304 and Al2024 by the plasma spraying method. The adgesion of the films varies depending on the substrates and the laminating method. In the case of STS304, the cracks were observed at thermal shock temperature difference ${Delta}T$ of $900^{circ}C$ in the non functionally gradient material(NFGM) and at $1100^{circ}C$ in the functionally gradient material(FGM). The film adhesion of the FGM is better than that of the NFGM in ST304. The cumulative AE count of the FGM of STS304 increased continuously at the bending test. But the NFGM of STS304 showed discontinuity of the AE count. The total AE count for the FGM of STS304 decreased as the number of thermal shock increased, and this tendency was evident as the thermal shock temperature difference increased.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.153-154
• /
• 2002

Wear map of silver coatings on AISI 52100 has been constructed to delineate the wear transition behavior with the change in operating conditions in various environments. Three main regimes were clearly identified: (i) elastic/plastic deformation of silver coating without failure. (ii) mild wear regime after initial failure of silver coating and (iii) severe wear regime. In the mild wear regime, the contact surfaces were covered with transfer layers of agglomerated wear particles. The transfer layer acted as a protective layer and resulted in low friction even after the initial failure of the coated films, whose characteristics were strongly dependent on both the operating and environmental conditions. Also, the existence of the critical sliding speed, above which no transfer layer was able to form, was discussed in the work.

• 한국재료학회지
• /
• 제3권3호
• /
• pp.261-271
• /
• 1993

4.5 Pb($Zn_{1/3}Nb_{2/3})O_3-40.5Pb(Ni_{1/3}Nb_{2/3})O_3$-55PZT와 PLZT(10/70/30, 11/60/40)를 경사조성으로 하여 경사기능 재료를 제조하였으며, 그 유전 특성과 압전 변형율 특성을 조사하였다. 경사기능재료는 A/B/A의 세층으로 성형하고 소결한 후 한 층을 연마해내어 제작하였다. 닥터블레이드용 슬립에는 acrylic계 유기 결합제가 34-36wt% 혼합되었으며, 건조 후 균열이 없는 양호한 thick film을 제조하였다. $1250^{\circ}C$, 2시간의 소성에 의해 경사기능화된 시편은 Nb와 La등의 조성 차이에 의한 구배를 이루었으며, 구배영역은 약 30${\mu}$m 정도였다. 경사기능재료에서 유전상수나 큐리온도롸 같은 유전특성은 조합한 조성층의 특성들사이의 값을 나타내었다. 인가 전압에 따른 변형율 특성은 단일 조성의 시편보다 현저하게 증가하였다. 실제로 경사기능 압전엑튜에이터를 제조한 결과 약 3${\mu}$m/100V 정도의 변위향을 나타내었다.