• 통합자연과학논문집
• /
• 제12권2호
• /
• pp.29-34
• /
• 2019

In dental resin cement studies, viscosity is also an important factor in the adhesion of tooth defects and implants. This study used BisGMA and HPMA as the main ingredients, triethylene glycol dimethacrylate (TEGDMA) as a diluent, and benzoyl peroxide (BPO) as a photoinitiator. The physical properties of graphene oxide used as an additive for functionality were evaluated, and its use as a dental resin cement material was investigated.The rupture strength has the tendency to increase along with the increase of the ratio of graphene oxide that was added, which seemed to reflect the effect of the high strength property of graphene oxide. The flexural strength also has the tendency to increase when about 0.5% of graphene oxide was added the same as the increase of rupture strength.When graphene oxide was added, according to viscosity use, the utilization as high-quality dental resin cements will increase.

• Journal of the Korean Wood Science and Technology
• /
• 제32권6호
• /
• pp.23-35
• /
• 2004

The goal of study was to investigate the influence of the acrylated urethane oligomer on mechanical properties, the chemical resistance and thermal resistance of the UV curable urethane acrylate coatings for fancy veneer overlayed plywood flooring. The pencil hardness and abrasion resistance of the coated fancy veneer overlayed plywood floorings increased with increasing the acrylate functionality of the acrylated urethane oligomer. In the case of the UV cured film containing hexa-functional acrylated aliphatic urethane oligomer, high discoloration of the coated fancy veneer overlayed plywood flooring was observed near the cracks at the beginning of the chemical treatment. In this study, it was found that the degradation of the UV cured film caused by an alkaline reagent was higher than that of the UV cured film caused by an acidic treatment.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.899-904
• /
• 2001

The impact of PVD coatings can be summed up in practical terms: this technology historically complements the best designed tool substrates to enhance cutting performance. PVD coatings are now incorporated in 25% of all HSS tools. The functionality is to extend the machining speed range, improve wear resistance at the cutting edge, and reduce friction at chip/tool contact areas to allow easier chip evacuation. These translate to a larger safe zone, as discussed in the failure mode diagram, for better productivity and higher reliability in machining operations of the customer. PVD coatings therefore represent an enabling technology that extends the application range of cutting tools in response to modern industrial needs. PVD coatings prolong the product life cycle of HSS tools and help this "mature" material to hold its territory against the advent of the newer hardmetal and ceramic tool materials. There is a lot of competitive life left particularly in PVD coated HSS endmills, drills, threading/tapping tools. PM HSS technology further increases the possibilities.ibilities.

• 복식
• /
• 제55권4호
• /
• pp.62-78
• /
• 2005

The modern period was the time that the most radical and extensive social and mental changes were occurring throughout the history, and modernism was prevailing as a general cognition system of people. Modernism, which carries principles of progress, belief in application of scientific technology, worship of reason, ideal of liberty as a col-e value of civilization, was plated as a leading ideology in the realm of society, culture and art In the early 20th century. In this study, the formative characteristics of modernism seen in architecture and fashion are analogized and analyzed in four ways ell the basis of the theory of p. Greenhalgh. First, 'Standardization for mass-production', which is analogized which P. Greenhalgh's 'Decompart-mentalisation', 'Social Morality', and' Technology'. Standardization for mass-production in architecture focuses on the development of a design prototype in order to mass produce; the development of ready-made clothes is actively done ill the fashion area for the same purpose as well. Second, 'Rational functionality' coming from P. Greenhalgh's 'The total work of art' and 'Function'. While rational functionality in architecture puts an emphasis on the rational operation of all the functions in regard to the relation between each part and the whole, rational functionality in fashion call be mainly seen in a dramatic increase in physical activity which could be hardly found before the modernism period. Namely, all the fashion design elements are developed for a certain rational and functional design on each part as well as on the whole in order to greatly increase physical activity. Third, 'the pursuit for genuineness of objects and universality of beauty' is on the analogy of P Greenhalgh's 'Truth', 'Anti-historicism', 'Abstraction', 'Internationalism/Universality'. This idea is adopted in architecture in the form of design of geometrical abstraction. In the same way, design using geometrical abstraction comes to have a significant meaning in fashion of the modernism period. So to speak, modernism architecture and fashion can be reborn to become an inter·national style by giving up the decorative and regional design prevailing before modernism and by expressing universal aesthetics in the form of simplicity and abstraction instead. Fourth, 'Expression of progress through a change in a viewpoint' stems from P. Greenhalgh's 'Progress', 'Transformation of Consciousness', 'Theology'. In architecture, this concept appears by using new construction materials and methods and by representing new aesthetical idea. As a result, it makes it possible for people to make progress for better lives. Like in architecture, new attempts for material application and processing are made in fashion. This gives rise to a general change in a viewpoint related to fashion, so that a flew fashion design which there has never been before can come out.

• 한국화재소방학회논문지
• /
• 제31권6호
• /
• pp.91-98
• /
• 2017

본 논문은 PVC 절연재료의 가속열화에 따른 트래킹 특성에 관한 연구이다. PVC 절연재료를 절연열화 시키기 위해 가속수명 시험방법 중 아레니우스 방정식을 이용한 가속열화실험을 진행하여 등가연수 0년, 10년, 20년, 30년, 40년 된 실험시료를 제작하였다. 그 후 KS C IEC 60112 기준에 의한 트래킹 실험을 진행하였다. 가속열화에 따른 PVC 트래킹 특성 측정 결과 염화암모늄 0.1%를 PVC 절연재료에 투하하였을 때, 트래킹은 발생하지 않았다. 하지만 트래킹 진전과정의 전류파형 및 전압파형을 등가수명 0년에서부터 40년까지 분석한 결과 절연성이 파괴되어 본 재질의 기능성을 갖지 못하는 BDB 구간까지 등가수명 0년을 기준으로 등가수명 10년의 경우 위험성 1.4배 증가, 20년의 경우 위험성 2배 증가, 30년의 경우 위험성 3.5배 증가, 40년의 경우 위험성 7배 증가하는 것으로 나타났다.

• 복식
• /
• 제65권3호
• /
• pp.76-90
• /
• 2015

This is a basic study of the two remaining armors (artifacts number K2366, K2368) from the late Joseon dynasty that is part of the Korean costume collection, which is preserved in the Mission Museum of Saint Ottilien in Germany. The armor No. 1 (artifacts number K2366) is a coat-styled armor with brass studs. It has a U-shaped neckline with the non-overlapping collars and sleeve straight-lined inseam. The armor No. 1 has the Mu to the sides and is not back slit. Both its inner and outer material are padded with cotton. Leather mails are attached on the inner lining, and studs are attached on the outer lining to match the leather mails. For this reason, the armor No. 1 can be named MyeonPiGab (brass studded armor consisting of a cotton coat with internal leather mails). The outer material is faded to have the natural white, or antique white look and the patterns on it are indigo blue. The inner material is blue, but the original color is unknown since it is faded. The lotus blossoms and vine patterns are dyed on the surface of the outer material and a name is written on the inner material. The armor No. 1 was worn between the late 17th century and the 19th century. It is estimated that it was worn by military officers who were above the mid-rank in the end of the Joseon dynasty. The armor No. 2 (artifacts number K2368) is a coat-styled armor with brass studs and a low-cut U-shaped neckline. The armor No. 2 has a slit on the left armpit and a string around it. Studs are evenly attached on the armor. The iron mails are attached to the left chest area on its inner lining. It seems that it was designed with both formality and functionality in mind. The outer material is red flannel, the inner material is blue satin and the pads are cheesecloth. The side of its collars, cuffs, front lines, sidelines, back slit, and bottom lines are trimmed with fur. There are armors called "JeonCheolGap (brass studded armor consisting of a felt coat with internal iron mails)," which is similar to the armor No. 2, however, the similarities are limited because they are not made of the same material nor do they follow the same principle of nomenclature.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2008년도 제33회 펄프종이기술 국제세미나
• /
• pp.47-70
• /
• 2008

Cost efficiency is today the primary requirement in the paper and board industry. This has led therefore, to a greater preponderance of products with specifically designed functionality to take account of current industry needs. Continually increasing machine coating speeds together with these new coating colour components have put more emphasis on the importance of the correct rheology and water retention of the coating colours to achieve good runnability and end product quality. In the coating process, some penetration of the aqueous phase, to the base paper or board must occur to anchor the pre-coating to the base or the topcoat to the pre-coat. The aqueous phase acts as a vehicle not only for the binder, but also for the other components. If this water or material penetration is not controlled, there will be excessive material shift from the coating colour to the base, before immobilization of the coating colour will stop this migration. This can result in poor machine runnability, unstable system and uneven coating layer, impacting print quality. The performance of rheology modifiers or thickeners on the coating color have tended to be evaluated by the term, "water retention". This simple term is not sufficient to explain their performance changes during coating. In this paper we are introducing a new concept of "material retention", which takes note of the total composition of the coating colour material and therefore goes beyond the concept of only water retention. Controlled material retention leads to a more uniform z-directional distribution of coating colour components. The changes that can be made to z-directional uniformity will have positive effects on print quality as measured by surface strength, ink setting properties, print gloss, mottling tendency. Optical properties, such as light scattering, whiteness and light fastness delivery should also be improved. Additionally, controlled material retention minimizes changes to the coating colour with time in re-circulation giving less fluctuation in quality in the machine direction since it more closely resembles fresh coating for longer periods. Use of the material retention concept enables paper and board producers to have more stable runnability (i.e. lower process costs), improved end product quality (i.e. better performance of used chemicals) and/or optimized use of coating colour components (i.e. lower total formulation cost)

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.91-91
• /
• 2013

Imagine a world where we could biomanufacture hybrid nanomaterials having atomic-scale resolution over functionality and architecture. Toward this vision, a fundamental challenge in materials science is how to design and synthesize protein-like material that can be fully self-assembled and exhibit information-specific process. In an ongoing effort to extend the fundamental understanding of protein structure to non-natural systems, we have designed a class of short peptides to fold like proteins and assemble into defined nanostructures. In this talk, I will talk about new strategies to drive the self-assembled structures designing sequence of peptide. I will also discuss about the specific interaction between proteins and inorganics that can be used for the development of new hybrid solar energy devices. Splitting water into hydrogen and oxygen is one of the promising pathways for solar to energy convertsion and storage system. The oxygen evolution reaction (OER) has been regarded as a major bottleneck in the overall water splitting process due to the slow transfer rate of four electrons and the high activation energy barrier for O-O bond formation. In nature, there is a water oxidation complex (WOC) in photosystem II (PSII) comprised of the earthabundant elements Mn and Ca. The WOC in photosystem II, in the form of a cubical CaMn4O5 cluster, efficiently catalyzes water oxidation under neutral conditions with extremely low overpotential (~160 mV) and a high TOF number. The cluster is stabilized by a surrounding redox-active peptide ligand, and undergo successive changes in oxidation state by PCET (proton-coupled electron transfer) reaction with the peptide ligand. It is fundamental challenge to achieve a level of structural complexity and functionality that rivals that seen in the cubane Mn4CaO5 cluster and surrounding peptide in nature. In this presentation, I will present a new strategy to mimic the natural photosystem. The approach is based on the atomically defined assembly based on the short redox-active peptide sequences. Additionally, I will show a newly identified manganese based compound that is very close to manganese clusters in photosystem II.

• Journal of Korean Neurosurgical Society
• /
• 제53권2호
• /
• pp.65-71
• /
• 2013

Objective : In order to develop a novel nerve guidance channel using porcine small intestinal submucosa (SIS) for nerve regeneration, we investigated the possibility of SIS, a tissue consisting of acellular collagen material without cellular immunogenicity, and containing many kinds of growth factors, as a natural material with a new bioactive functionality. Methods : Left sciatic nerves were cut 5 mm in length, in 14 Sprague-Dawley rats. Grafts between the cut nerve ends were performed with a silicone tube (Silicon group, n=7) and rolled porcine SIS (SIS group, n=7). All rats underwent a motor function test and an electromyography (EMG) study on 4 and 10 weeks after grafting. After last EMG studies, the grafts, including proximal and distal nerve segments, were retrieved for histological analysis. Results : Foot ulcers, due to hypesthesia, were fewer in SIS group than in Silicon group. The run time tests for motor function study were 2.67 seconds in Silicon group and 5.92 seconds in SIS group. Rats in SIS group showed a better EMG response for distal motor latency and amplitude than in Silicon group. Histologically, all grafts contained some axons and myelination. However, the number of axons and the degree of myelination were significantly higher in SIS group than Silicon group. Conclusion : These results show that the porcine SIS was an excellent option as a natural biomaterial for peripheral nerve regeneration since this material contains many kinds of nerve growth factors. Furthermore, it could be used as a biocompatible barrier covering neural tissue.

• 한국식품영양학회지
• /
• 제31권5호
• /
• pp.631-639
• /
• 2018

The purpose of this study was to investigate the characteristics of macaroons prepared using natural color materials (Opuntia ficus-indica var. saboten (Re-N), mulberry leaf (Gr-N), pumpkin (Ye-N), and cocoa powder (Br-N)) and corresponding artificial food colorants (red (Re-A), yellow (Ye-A), green (Gr-A) and brown (Br-A)). The moisture content of macaroons prepared using natural color material was higher compared to the macaroons prepared using artificial food colorant. DPPH and ABTS radical scavenging activity was similar in both types of macaroons. Lightness and redness of Re-N, Gr-N, Ye-N, and Br-N macaroons were lower than Re-A, Gr-A, Ye-A and Br-A macaroons. Yellowness of Re-N was higher because of the browning reaction. The texture profile analysis revealed lower hardness when natural color powder was employed. In the sensory evaluation, overall acceptability was not significantly different between natural colored and artificial colored macaroons. As a result, macaroons with the natural color material were softer and showed higher antioxidative activity, however, organoleptic properties were not much different when compared with macaroons with artificial colors. Apparently, it is stated that more studies on the development of macaroons with more enhanced physical functionality and good taste using natural materials should be performed.