• Journal of the Korean Society for Railway
• /
• v.10 no.4
• /
• pp.438-443
• /
• 2007

This paper proposes an integrated SE process for the development of railway systems with safety assessment included. Although the safety assessment process must be performed with SE process properly with good coordination, the interfaces between the two processes have not been clear. Thus, in many of safety critical system developments in Korea, it is difficult to assess safety in proper development phase. The process model proposed in this paper is based on both the concept of system life cycle and the repetitive use of SE process. In each of development phases, appropriate safety assessment methods are described. Also the evaluation of the integrated system incorporating safety factors is described. The resultant process model is expressed by the Enhanced Functional Flow Block Diagram (EFFBD) using a CASE tool. The model also allows timeline analysis for identifying activity flow and data flow, resulting in the effective management of process. In conclusion, the integrated process enable both the SE process and safety assessment process to cooperate with each other from early development phase throughout the whole system life cycle.

• Journal of the Korea Safety Management & Science
• /
• v.10 no.4
• /
• pp.73-81
• /
• 2008

The current electrical safety plan developed for the national electricity system has been playing an important role in handling a variety of electrical accidents. However, it can be more effective to prevent or reduce those accidents if a preventive electrical safety plan is available. In this paper, an approach to developing the safety plan is described. We first discuss the contents that should be included in the plan. Noting that an effective plan requires the system level consideration of all the factors affecting the safety issues, an operation concept document (OCD) is considered. The OCD can allow us to understand the behavior of the safety system based on the operation environment, the system functions, the performance requirements, all at the system level of the safety system. Thus, the OCD can be useful in developing the safety plan. A detailed description then follows on how the OCD is developed for the electrical safety system under study. Finally, we discuss how the developed OCD can be used in deriving the preventive electrical safety plan.

• International Journal of Computer Science & Network Security
• /
• v.21 no.6
• /
• pp.252-257
• /
• 2021

The application of the principle of trigeneration allows to simultaneously provide electricity to power electronic devices, as well as heat and cold to create the necessary microclimate of the premises and increase efficiency compared to separate cooling and heating systems. The use of Peltier thermoelectric modules (TEM) as part of trigenerative systems allows for smooth and precise control of the temperature regime, high manufacturability and reliability due to the absence of moving parts, resistance to shock and vibration, and small weight and size parameters of the system. One of the promising areas of improvement of trigenerative systems is their modeling and optimization based on the automatic control theory. A block diagram and functional model of an energy-saving trigenerative climate control system based on Peltier modules are developed, and the transfer functions of an open and closed system are obtained. The simulation of the transient characteristics of the system with varying parameters of the components is performed. The directions for improving the quality of transients in the climate control system are determined, as well as the prospects of the proposed methodology for modeling and analyzing control systems operating in substantially nonlinear modes.

• Journal of the Korean Society of Systems Engineering
• /
• v.14 no.2
• /
• pp.73-82
• /
• 2018

In this work, a hardware based cryptographic module for the cyber security of nuclear power plant is developed using a system engineering approach. Nuclear power plants are isolated from the Internet, but as shown in the case of Iran, Man-in-the-middle attacks (MITM) could be a threat to the safety of the nuclear facilities. This FPGA-based module does not have an operating system and it provides protection as a firewall and mitigates the cyber threats. The encryption equipment consists of an encryption module, a decryption module, and interfaces for communication between modules and systems. The Advanced Encryption Standard (AES)-128, which is formally approved as top level by U.S. National Security Agency for cryptographic algorithms, is adopted. The development of the cyber security module is implemented in two main phases: reverse engineering and re-engineering. In the reverse engineering phase, the cyber security plan and system requirements are analyzed, and the AES algorithm is decomposed into functional units. In the re-engineering phase, we model the logical architecture using Vitech CORE9 software and simulate it with the Enhanced Functional Flow Block Diagram (EFFBD), which confirms the performance improvements of the hardware-based cryptographic module as compared to software based cryptography. Following this, the Hardware description language (HDL) code is developed and tested to verify the integrity of the code. Then, the developed code is implemented on the FPGA and connected to the personal computer through Recommended Standard (RS)-232 communication to perform validation of the developed component. For the future work, the developed FPGA based encryption equipment will be verified and validated in its expected operating environment by connecting it to the Advanced power reactor (APR)-1400 simulator.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1994.10a
• /
• pp.49-58
• /
• 1994

The methods of estimation of VTS effectivenss are compared and the worldwide literature related to the VTS effectiveness is reviewed. The review suggests three potential approaches ; simulation ; synthesis of expert opinion and statistical analysis of casualties. this study adopted dissimilar approaches to estimate the VTS effectiveness to the earlier studies ; the combination of synthesis of expert opinion and causal analysis of casualty. The VTS effectiveness is derived by multiplying casualty rate reduction factors by the effect level of causal factors. The development of casualty rate reduction factors was based on the questionnaire survey and the evolution of effect levels was based on the causal analysis using functional block diagram. According to these procedures the maximum benefit to be obtained through the introduction of a VTS system was approximately 46 percent overall. The collision reduction rate was estimated to be approximately 50 percent for a VTS system with advanced radar surveillance. And 47 percent of groundings 36 percent of rammings and 21 percent of founderings could be reduced by the introduction of VTS. These figures are more or less the same to the earlier studies. The VTS effectiveness by the different causal factor groups was examined. VTS may reduce about 68 percent of causal factors classified as environmental conditions 40 percent of human factors and 35 percent of technical factors in collision accidents. As a whole 60 percent of environmental factors 41 percent of human factors and 20 percent of technical factors may be prevented by a VTS. The key variable of the effectiveness percentage is the value of weight coefficient $\delta$. Therefore differing values for this input was discussed and the impact that these variations have on the VS effectiveness noted. As the results of sensitivity analysis of VTS effectiveness by $\pm$10 percent the effectiveness is varied approximately three to seven percent by casualty type. And the value is changed roughly four to eight percent by a $\pm$10 percent variation by different sub-areas.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.12
• /
• pp.1216-1227
• /
• 2013

GNSS(Global Navigation Satellite System) is now being widely used in both civilian and military applications where accurate positioning and timing information are required and it is considered as a representative convergence technique in IT-Military application techniques. However, GNSS has low sensitivity level of GNSS receivers and is vulnerable to jamming signal, since the signals come from the satellite located at approximately 20,000 Km above the earth. The studies for the anti-jamming techniques in military applications have been passively performed in the domestic, because the information related GNSS are dependent on the countries that have GNSS. In this paper, we show the effect of jammer ERP by analyzing the link budget of GPS J/S power as a function of distance between jammer and receiver. Also, we categorize the anti-jamming techniques based on the functional block diagram of GNSS receiver structure and analyze the recent anti-jamming GNSS products and their technologies developed in domestic and foreign countries.

• Journal of the Korea Society for Simulation
• /
• v.29 no.1
• /
• pp.31-38
• /
• 2020

Mission reliability is defined by the probability of accomplishing the requirements task that were targeted in product development, and in the case of combat systems, mission reliability is an important factor that will determine victory or defeat, unlike commercial equipment. The mission reliability of the existing domestic combat system was calculated by considering only the physical connections of the equipment involved in the mission performance, but as the equipment becomes increasingly sophisticated and complex, it is impossible to determine the mission relevance solely by physical connection. Thus, in this paper, improved mission reliability was calculated using SysML, the system design modeling language, by taking into account the functional connection as well as physical connection. Based on this research, we look forward that the mission reliability of the combat system that will be developed in the future will be used as a verification material.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.7-18
• /
• 2005

Over the past twenty years, the maintenance system has been developed and its importance has been increased. For the effective maintenance of the urban transit, we have developed the maintenance system based on the concept of RCM(Reliability Centered Maintenance). RCM analysis is a systematic approach to developing a cost-effective maintenance strategy based on the various components's reliability of the system in question. It is performed according to process that includes the following steps; definition of function and functional failures of the systems, construction of RB D(Reliability Block Diagram), performance of FMEA(Failure Modes & Effects Analysis) and calculation of the reliability index. The final process of RCM is to determine appropriate failure maintenance strategies. This paper aims to define the procedure of maintenace based on the concept of RCM for urban transit. The key for a successful maintenance system is an automated scheduling to the maximum extent possible and timely executions. The developed system issues maintenance plan and repair request based on analyzed data and maintenance experience.

• Journal of Korean Society for Quality Management
• /
• v.41 no.4
• /
• pp.725-735
• /
• 2013

Purpose: The purpose of this study is to propose an Integrated Safety Evaluation Process (ISEP) that can enhances the safety aspect of the safety-critical system. This process utilizes the advantages of the iterative Systems Engineering process combined with the safety assessment process that is commonly and well defined in many standards and/or guidelines for railway, aerospace, and other safety-critical systems. Methods: The proposed process model is based on the predefined system lifecycle, in each phase of which the appropriate safety assessment activities and the safety data are identified. The interfaces between Systems Engineering process and the safety assessment process are identified before the two processes are integrated. For the integration, the elements at lower level of Systems Engineering process are combined with the relevant elements of safety assessment process. This combined process model is represented as Enhanced Functional Flow Block Diagram (EFFBD) by using CORE(R) that is commercial modelling tool. Results: The proposed model is applied to the lifecycle and management process of the United States aircraft system. The US aircraft systems engineering process are composed of twelve key elements, among which the requirements management, functional analysis, and Synthesis processes are considered for examplenary application of the proposed process. To synchronize the Systems Engineering process and the safety assessment process, the Systems Engineering milestones are utilized, where the US aircraft system has thirteen milestones. Taking into account of the nine steps in the maturity level, the integrated process models are proposed in some phases of lifecycle. The flows of processes are simulated using CORE(R), confirming the flows are timelined without any conflict between the Systems Engineering process and the safety assessment process. Conclusion: ISEP allows the timeline analysis for identifying activity and data flows. Also, the use of CORE(R) is shown to be effective in the management and change of process data, which helps for the ISEP to apply for the development of safety critical system. In this study, only the first few phases of lifecyle are considered, however, the implementation through operation phases can be revised by combining the elements of safety activities regarding those phases.

• Investigative Magnetic Resonance Imaging
• /
• v.9 no.1
• /
• pp.43-49
• /
• 2005

A few studies have shown that the function of fusiform face area is selectively involved in the perception of faces including a race difference. We investigated the neural substrates of the face-selective region called fusiform face area in the ventral occipital-temporal cortex and same-race memory superiority in the fusiform face area by the event-related fMRI. In our fMRI study, subjects (Oriental-Korean) performed the implicit distinction of the race while they consciously made familiar-judgments, regardless of whether they considered a face as Oriental-Korean or European-American. For race distinction as an implicit task, the fusiform face areas (FFA) and the right parahippocampal gyrus had a greater response to the presentation of Oriental-Korean faces than for the European-American faces, but in the conscious race distinction between Oriental-Korean and European-American faces, there was no significant difference observed in the FFA. These results suggest that different activation in the fusiform regions and right parahippocampal gyrus resulting from superiority of same-race memory could have implicitly taken place by the physiological processes of face recognition.