• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.970-976
• /
• 2007

This paper presents a novel polar transmitter architecture with a 2-bit sigma-delta modulator. In the proposed architecture, the 2-bit sigma-delta modulator is introduced to suppress quantization noise of conventional sigma-delta modulator. The power amplifier configuration is also modified in a binary form to accommodate the 2-bit digitized envelope signal. The Ptolemy simulation results of the proposed structure show that the spectral property is greatly improved in full transmit band of EDGE system. The fine quantization scheme of the 2-bit modulator lowers the noise level by 10dB without increasing the over-sampling ratio, which may be obtained if the over-sampling ratio increases twofold. Dynamic range is also enhanced up to 5dB owing to the new form of the power amplifier in the transmitter.

• Progress in Medical Physics
• /
• v.27 no.4
• /
• pp.272-276
• /
• 2016

To investigate the optimum x-ray tube design for the dental radiology, factors affecting x-ray beam characteristics such as tungsten target thickness and anode angle were evaluated. Another goal of the study was to addresses the anode heel effect and off-axis spectra for different target angles. MCNPX has been utilized to simulate the diagnostic x-ray tube with the aim of predicting optimum target angle and angular distribution of x-ray intensity around the x-ray target. For simulation of x-ray spectra, MCNPX was run in photon and electron using default values for PHYS:P and PHYS:E cards to enable full electron and photon transport. The x-ray tube consists of an evacuated 1 mm alumina envelope containing a tungsten anode embedded in a copper part. The envelope is encased in lead shield with an opening window. MCNPX simulations were run for x-ray tube potentials of 70 kV. A monoenergetic electron source at the distance of 2 cm from the anode surface was considered. The electron beam diameter was 0.3 mm striking on the focal spot. In this work, the optimum thickness of tungsten target was $3{\mu}m$ for the 70 kV electron potential. To determine the angle with the highest photon intensity per initial electron striking on the target, the x-ray intensity per initial electron was calculated for different tungsten target angles. The optimum anode angle based only on x-ray beam flatness was 35 degree. It should be mentioned that there is a considerable trade-off between anode angle which determines the focal spot size and geometric penumbra. The optimized thickness of a target material was calculated to maximize the x-ray intensity produced from a tungsten target materials for a 70 keV electron energy. Our results also showed that the anode angle has an influencing effect on heel effect and beam intensity across the beam.

• Clinical and Experimental Pediatrics
• /
• v.61 no.3
• /
• pp.78-83
• /
• 2018

Purpose: Frequent desaturation due to immature incoordination of suck-swallow-breathing in preterm infants can influence multiple organs such as the heart, lungs, and brain, which can then affect growth and development. Most notably in preterm infants, feeding desaturation may even affect pulmonary function during gavage feeding. Because respiratory muscle activities may reflect the work required during respiration, we evaluated the differences in these activities between full-term and preterm infants with feeding desaturation, and investigated the correlations with clinical variables. Methods: Nineteen preterm infants with feeding desaturation (group 1) and 19 age-matched full-term infants (group 2) were evaluated. Oromotor function was evaluated using video recording. The root-mean-square (RMS) envelope of the electromyography signal was calculated to quantify the activities of muscles involved in respiration. The differences in RMS between both groups and the correlation with clinical variables including gestational age (GA), birth weight (BW), and Apgar scores (AS) at 1 and 5 minutes after birth were evaluated. Results: The RMS values of the diaphragm (RMS-D) and rectus abdominis (RMS-R) were significantly greater in group 1 compared to group 2, and the 1- and 5-min AS were significantly lower in group 1 compared to group 2. RMS-D and RMS-R were inversely correlated with GA, BW, 1- and 5-min AS in all infants. Conclusion: This study showed that respiratory muscle activities were augmented during feeding in preterm infants compared to full-term infants. Additionally, respiratory muscle activities were inversely correlated with all clinical variables.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.383-387
• /
• 2004

The Fuel Test Loop (FTL) consists of In-Pile Test Section (IPS) and Out-of-Pile System (OPS). The test condition in IPS such as pressure, temperature and quality of the main cooling water, can be controlled by the OPS. The FTL has been developed to be able to irradiate three pins to the core irradiation hole (IR1 hole) by considering for its utility and user's irradiation requirement. The IPS vessel assembly (IVA) consists of IPS head, outer pressure vessel, inner pressure vessel, inner assembly and test fuel carrier. The IVA is approximately 5.6 m long and fits within a 74 mm in diameter envelope over the full height of the chimney. Above the top of the chimney, the head of the IPS is enlarged to allow the closure flanges and pipe work connections. IVA was designed to test the CANDU and PWR nuclear fuel pin together. Specially, wished to minimize interference by nuclear fuel change in design and synthesize these items and shape design for IVA.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.1
• /
• pp.120-131
• /
• 2016

The full results of troubleshooting process related to the flight control system of a tilt-rotor type UAV in the flight tests are described. Flight tests were conducted in helicopter, conversion, and airplane modes. The vehicle was flown using automatic functions, which include speed-hold, altitude-hold, heading-hold, guidance modes, as well as automatic take-off and landing. Many unexpected problems occurred during the envelope expansion tests which were mostly under those automatic functions. The anomalies in helicopter mode include vortex ring state (VRS), long delay in the automatic take-off, and the initial overshoot in the automatic landing. In contrast, the anomalies in conversion mode are untrimmed AOS oscillation and the calibration errors of the air data sensors. The problems of low damping in rotor speed and roll rate responses are found in airplane mode. Once all of the known problems had been solved, the vehicle in airplane mode gradually reached the maximum design speed of 440km/h at the operation altitude of 3km. This paper also presents a comprehensive detailing of the control systems of the tilt-rotor unmanned air vehicle (UAV).

• Journal of Microbiology and Biotechnology
• /
• v.15 no.6
• /
• pp.1229-1239
• /
• 2005

Human immunodeficiency virus-like particles (HIVVLPs) with native conformations similar to that of the wild-type virion could be valid candidates for vaccine development. To this end, we used a Semliki Forest Virus (SFV) expression system to produce HIV- VLPs containing high quantities of native envelope proteins. Here, we described a single SFV replicon containing the HIV gagpol and env genes under the control of separate subgenomic promoters. Mature VLPs incorporating the Gag and Env proteins were detected in the supernatant of replicon-expressing cells by Western blot analysis. The HIV-VLPs showed the expected molecular density (1.14-1.18 g/ml) on a $20-60\%$ sucrose gradient; the particles were 100-120 nm in diameter and Env proteins were observed on their surfaces by immunogold electron microscopy. RT-PCR analysis of VLP-associated RNAs in mature HIV-VLPs revealed two SF V-derived RNA species (full-length and subgenomic). Immunization studies in Balb/c mice showed that these HIV-VLPs were capable of inducing both HIV-specific antibodies and cell-mediated immune responses. Taken together, our results indicate that the SFV replicon system is useful for the production of HIV-VLPs, which may be valuable candidates for an HIV vaccine.

• Wind and Structures
• /
• v.11 no.5
• /
• pp.361-376
• /
• 2008

This paper considers internal pressure fluctuations for a range of building volumes and dominant wall opening areas. The study recognizes that the air flow in and out of the dominant opening in the envelope generates Helmholtz resonance, which can amplify the internal pressure fluctuations compared to the external pressure, at the opening. Numerical methods were used to estimate fluctuating standard deviation and peak (i.e. design) internal pressures from full-scale measured external pressures. The ratios of standard deviation and peak internal pressures to the external pressures at a dominant windward wall opening of area, AW are presented in terms of the non-dimensional opening size to volume parameter, $S^*=(a_s/\bar{U}_h)^2(A_W^{3/2}/V_{Ie})$ where $a_s$ is the speed of sound, $\bar{U}_h$ is the mean wind speed at the top of the building and $V_{Ie}$ is the effective internal volume. The standard deviation of internal pressure exceeds the external pressures at the opening, for $S^*$ greater than about 0.75, showing increasing amplification with increasing $S^*$. The peak internal pressure can be expected to exceed the peak external pressure at the opening by 10% to 50%, for $S^*$ greater than about 5. A dominant leeward wall opening also produces similar fluctuating internal pressure characteristics.

• 한국태양에너지학회:학술대회논문집
• /
• 2008.04a
• /
• pp.55-60
• /
• 2008

This study is on the analysis of power output of transparent thin-film PV windows which are integrated into the building envelope instead of traditional windows. 3 installation angles of vertical, horizontal and $30^{\circ}C$ inclination are investigated. To measure power output of PV windows, full scale mock-up house was designed and constructed. The power performance of PV window system was analyzed for horizontal angle, declination angle and vertical angle according to incline angle. Monitoring data are gathered from November 2006 to August 2007 and statistical analysis is performed to analysis a characteristics of power performance of transparent PV windows. Results show that annual power output of PV window with horizontal angle is 844.4kWh/kWp/year, declination angle 1,060kWh/kWp/year and vertical angle 431.6 kWh/kWp/year.

• Investigative Magnetic Resonance Imaging
• /
• v.4 no.1
• /
• pp.20-26
• /
• 2000

Gradient moment nulling techniques require the introduction of an additional gradient on each axis for each order of motion correction to be applied. The additional gradients introduce new constraints on the sequence design and increase the demands on the gradient system. The purpose of this paper is to demonstrate techniques for optimization of gradient echo gradient moment nulling sequences within the constraints of the gradient hardware. Flow compensated pulse sequences were designed and implemented on a clinical magnetic resonance imaging system. The design of the gradient moment nulling sequences requires the solution of a linear system of equations. A Mathematica package was developed that interactively solves the gradient moment nulling problem. The package allows the physicist to specify the desired order of motion compensation and the duration of the gradients in the sequence with different gradient envelopes. The gradient echo sequences with first, second, and third order motion compensation were implemented with minimum echo time. The sequences were optimized to take full advantage of the capabilities of the gradient hardware. The sequences were used to generate images of phantoms and human brains. The optimized sequences were found to have better motion compensation than comparable standard sequences.

• Geotechnical Engineering
• /
• v.14 no.5
• /
• pp.17-28
• /
• 1998

The design of a ground anchor wall calculating the design anchor force and anchored walls depends primarily on the earth pressure acting on anchored w deflection of the wall, the wall stiffness, distribution exists for anchored walls. In the apparent earth pressure envelope design of anchored walls. In this study, full scale anchored w pressure distribution was obtained from function. Earth pressures obtained from pressure and with the apparent earth pre the anchored wall in sand. It is conclude is appropriate for the anchored wall design.