• 제목/요약/키워드: Full Load

검색결과 1,446건 처리시간 0.032초

디젤기관에 있어서 에멀젼 연료가 연소특성에 미치는 영향 (Effects on the Characteristics of Combustion by using Emulsion Fuel in Diesel Engine)

  • 임재근;조상곤;황상진;유동훈;서장원
    • 한국마린엔지니어링학회:학술대회논문집
    • /
    • 한국마린엔지니어링학회 2006년도 전기학술대회논문집
    • /
    • pp.41-42
    • /
    • 2006
  • A study on the combustion characteristics by using Emulsion Fuel in Diesel Engine is performed experimentally. In this paper, the experiments are performed at engine speed 1800rpm, emulsion fuel ratio is 0%, 10%, 20%, and main measured items are specific fuel consumption, pressure, ratio of pressure rise, rate of heat release etc. The obtained conclusions are as follows. 1) Specific fuel consumption increase maximum 19.8% at low load, but is not effected at full load. 2) Ratio of pressure rise and rate of heat release are about the same in the case of 10% and 20% of emulsion fuel ratio. 3) Cylinder Pressure increase 11.7%, ratio of pressure rise increase 60.4% in case of emulsion fuel ratio 20% at full load. 4) Rate of heat release increase 76.9% in case of emulsion fuel ratio 20% at full load.

  • PDF

항공용 센서 포드의 정적 구조시험장비 개발 (Development of Full-Scale Static Test System for Aircraft Sensor Pod)

  • 조재명;박훈혁;이원웅;배종인;이한솔;오의환
    • 항공우주시스템공학회지
    • /
    • 제17권1호
    • /
    • pp.97-105
    • /
    • 2023
  • 항공용의 센서 포드는 비행체 기동조건에서 유도된 비행 하중에 대하여 정적 구조시험을 통한 구조 건전성을 검증해야 한다. 이를 위해 센서 포드 전 구조체의 정하중 시험장비 개발이 필수적으로 요구된다. 본 논문에서는 시험요구도를 기본으로 정적 구조시험의 구성 및 시험 구조물, 시험체 구속장치, 하중 인가장치, 제어 및 계측장비 등의 설계, 제작, 조립 및 검증에 대한 방법과 절차들을 확보하였다. 결론적으로 센서 포드의 정하중 시험 및 데이터 획득을 성공적으로 수행하였으며, 시험장비의 신뢰성도 함께 입증하였다.

A Novel Induction Heating Type Super Heated Vapor Steamer using Dual Mode Phase Shifted PWM Soft Switching High Frequency Inverter

  • Sugimura, Hisayuki;Eid, Ahmad;Lee, Hyun-Woo;Nakaoka, Mutsuo
    • 전력전자학회:학술대회논문집
    • /
    • 전력전자학회 2005년도 전력전자학술대회 논문집
    • /
    • pp.774-777
    • /
    • 2005
  • In this paper, a constant frequency phase shifting PWM controlled voltage source full bridge-type series load resonant high-frequency inverter using the IGBT power modules is presented for innovative consumer electromagnetic induction heating applications such as a hot water producer, steamer and super heated steamer. The full bridge arm side link passive quasi-resonant capacitor snubbers in parallel with the each power semiconductor device and high frequency AC load side linked active edge inductive snubber-assisted series load resonant tank soft switching inverter with a constant frequency phase shifted PWM control scheme is discussed and evaluated on the basis of the simulation and experimental results. It is proved from a practical point of view that the series load resonant and edge resonant hybrid high-frequency soft switching PWM inverter topology, what is called class DE type. including the variable-power variable-frequency(VPVF) regulation function can expand zero voltage soft switching commutation range even under low output power setting ranges, which is more suitable and acceptable for induction heated dual packs fluid heater developed newly for consumer power utilizations. Furthermore, even in the lower output power regulation mode of this high-frequency load resonant tank high frequency inverter circuit it is verified that this inverter can achieve ZVS with the aid of the single auxiliary inductor snubber.

  • PDF

가정용 목재 펠릿 보일러에 대한 부분부하 운전 특성 (Part Load Performance Characteristics of Domestic Wood Pellet Boiler)

  • 강새별;김종진;김혁주;박화춘;최규성;심봉석
    • 한국신재생에너지학회:학술대회논문집
    • /
    • 한국신재생에너지학회 2010년도 추계학술대회 초록집
    • /
    • pp.103.1-103.1
    • /
    • 2010
  • Recently domestic wood pellet boilers are installed in rural and forestry houses. The fuel price per lower heating value of wood pellet is about 20 % lower than that of heating oil on July 2010. In spite of lower price of wood pellet, a few user of wood pellet boiler complain expensive fuel cost. One of this reason is inaccurate or improper air-fuel ratio setting of wood pellet boiler. O2 concentration of flue gas of domestic wood pellet boiler is about 9.7 % and there are few domestic wood pellet boiler which can control air-fuel ratio automatically. We tested a domestic wood pellet boiler in changing boiler thermal output and air-fuel ratio. The nominal boiler thermal output is 25 kW (21 500 kcal/h). We measured thermal efficiency and flue gas concentrations such as CO and NOx at each boiler thermal load with various air-fuel ratio. The results show that if air flow rate is the same as full load and part load, thermal efficiency of part load of 40 % drops about 7.7 %p compared to boiler full load case.

  • PDF

쇄빙상선의 빙하중 추정식 고찰 (Ice Load Prediction Formulas for Icebreaking Cargo Vessels)

  • 최경식;정성엽
    • 대한조선학회논문집
    • /
    • 제45권2호
    • /
    • pp.175-185
    • /
    • 2008
  • One of the concerns that arise during navigation in ice-covered waters is the magnitude of ice loads encountered by ships. However, the accurate estimation of ice loads still remains as a rather difficult task in the design of icebreaking vessels. This paper focuses on the development of simple ice load prediction formulas for the icebreaking cargo vessels. The maximum ice loads are expected from unbroken ice sheet and these loads are most likely to be concentrated at the bow area. Published ice load data for icebreaking vessels, from the model tests and also from full-scale sea trials, are collected and then several ice load prediction formulas are compared with these data. Finally, based on collected data, a semi-empirical ice load prediction formula is recommended for the icebreaking cargo vessels.

바이오 가스를 사용하는 가스터빈 열병합 시스템의 전부하 및 부분부하 운전특성 해석 (A Study on Full and Part Load Operations of a Biogas-fired Gas Turbine Combined Heat and Power System)

  • 강도원;이종준;김동섭;허광범
    • 한국유체기계학회 논문집
    • /
    • 제14권2호
    • /
    • pp.35-40
    • /
    • 2011
  • This study analyzed the influence of firing biogas on the performance and operation of a gas turbine combined heat and power (CHP) system. A reference CHP system designed with natural gas fuel was set up and off-design simulation was made to investigate the impact of firing biogas in the system. Changes in critical operating parameters such as compressor surge margin and turbine blade temperature caused by firing biogas were examined, and a couple of operating schemes to mitigate their changes were simulated. Part load operation of the biogas-fired system was compared with that of natural-gas fired system, and it was found that as long as the two system produce the same electric power output, they exhibit nearly the same heat recovery.

압축기출구에 공기분사가 터보과급 디젤기관의 성능에 미치는 영향에 관한 연구 (A Study on the Effects of Injected Air into the Compressor Exit for the Performances of a Turbocharged Diesel Engine)

  • 최낙정;이창식
    • 대한기계학회논문집
    • /
    • 제19권3호
    • /
    • pp.796-805
    • /
    • 1995
  • For the purpose of improving performances of a turbocharged diesel engine at low speed, this study investigates the effects of the injected air for the performances and flow characteristics in the intake and exhaust pipes by using the computer simulation with test bed. In the theoretical analysis, the whole flow system, including engine cylinders and intake and exhaust pipes, is calculated numerically by the method of filling and emptying. From the results of this study, the following conclusions may be summarized. Increasing injected air pressure into the pipe of compressor exit brings about the improvement in a performance and flow characteristics of intake and exhaust pipes under full load operating conditions at 1000 rpm of the engine speed, but shows trends of the inferior performances under no load operating conditions at 2000 rpm of the engine speed.

현가장치 볼 조인트의 동적 모델 연구 (Dynamic Modeling of Ball Joint in Suspension)

  • 김숙희;한형석;노규석;김명규;김기훈
    • 한국정밀공학회:학술대회논문집
    • /
    • 한국정밀공학회 2003년도 춘계학술대회 논문집
    • /
    • pp.1561-1564
    • /
    • 2003
  • In the dynamic analysis model of full vehicles, the ball joint is usually modeled as an ideal joint. Searching a ball joint, the engineering plastic covers metal and the plastic has little compliance. It is expected that the compliance will physically have an influence on load transfer. This thesis presents a dynamic model considering the compliance of a ball joint, and studies an influence related to load transfer. It models the compliance of a ball joint to 3 directional spring. Likewise, it researches the load of a ball joint via a four-post simulation of a full vehicle, comparing with a model considered compliant and the model of an ideal joint. As a result, the difference between the compliance and the ideal joint model was determined. For this reasons, to conduct precision load prediction for durability analysis, dynamic analysis considering the compliance of bali joint should be required.

  • PDF

T-50 전기체 내구성시험 시험하중 설계기술 연구 (A Study on the Test Load Simulation Technique for T-50 Full Scale Durability Test)

  • 정재권;이기범;양명석;설창원
    • 한국항공우주학회지
    • /
    • 제32권3호
    • /
    • pp.82-87
    • /
    • 2004
  • 항공기 구조 개발에 관련된 MlL-HDBK-1530 에는 구조 건전성을 확보하기 위한 요구사항이 기술되어있다. 기체 구조의 내구성 및 손상허용성은 요구항목 중의 하나로서 관련 규격서의 요구조건과 절차에 따라 해석 및 시험을 통하여 입증되어야 한다. 본 논문에서는 T-50 항공기 (고등 훈련기)의 안전성 및 내구성 평가를 위한 전기체 내구성 시험하중 설계에 대하여 기술하였다. 내구성 시험하중 설계는 대한민국 공군과 미군사규격서의 요구조건 및 절차에 따라 수행되었다. 실제 비행상태 구현을 위한 전기체 부유식 시험조립 기법과 비행대비행 하중 스펙트럼의 모든 하중을 정확하게 모사 할 수 있는 시험 하중 최적화 기법 및 6-자유도 평형기법을 개발하여 적용하였다. 개발된 기법은 향후 항공기 전기체 구조시험을 수행하는데 있어서 유용한 시험하중 설계 기법임을 확인하였다.