• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.1
• /
• pp.111-119
• /
• 2015

The negative factors of fishery in environmental aspect of view are Greenhouse gas emission problems by high usage of fossil fuel, destruction of underwater ecosystem by bottom trawls, reduction of resources by fishing and damage of ecosystem diversity. Especially, the Greenhouse gas emission from fisheries is an important issue due to Canc$\acute{u}$n meeting, Mexico in 1992 and Kyoto protocol in 2005. However, the investigation on the GHG emissions from Korean fisheries did not much carry out. Therefore, the quantitative analysis of GHG emissions from Korean fishery industry is needed as a first step to find a relevant way to reduce GHG emissions from fisheries. The purpose of this research is to investigate which degree of GHG emitted from fishery. Here, we calculated the GHG emission from Korean bottom pair trawl fishery using the LCA (Life Cycle Assessment) method. The system boundary and input parameters for each process level are defined for LCA analysis. The fuel use coefficient of the fishery is also calculated. The GHG emissions from the representative fishes caught by bottom pair trawl will be dealt with. Furthermore, the GHG emissions for the edible weight of fishes are calculated with consideration to the different consuming areas and slaughtering process also. The results will be helpful to understand the circumstances of GHG emissions from Korean fisheries.

• Proceedings of the KIEE Conference
• /
• 1999.07c
• /
• pp.1183-1185
• /
• 1999

The basic purpose of economic dispatch problem is that minimize fuel cost with inequality constraint of generator output. To solve this problem it is very important to express power loss equation that have quadratic function of generator output power included B-coefficient. This Paper presents a method in determining B-coefficient by use A-matrix that is calculated by loss re-distribution algorithm (LRDA) considering voltage dependent load model (VDLM)s. The Proposed algorithm is tested with IEEE 6 bus sample system, which shows the result in each cases by the change of load component factor.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.218-220
• /
• 1997

In power system, economic dispatch problem is to minimize fuel cost with inequality constraints of generator output. To solve this problem it is very important to express power loss equation that have Quadratic function of generator power included B-coefficient. This paper presents a method in determining B-coefficient by use A-matrix that is calculated by power flow considering voltage dependent static load model. The proposed algorithm is tested with IEEE 6 bus sample system, which shows the result in each cases by the change of load component factor.

• Journal of Power System Engineering
• /
• v.22 no.1
• /
• pp.48-55
• /
• 2018

It has recently been reported that methanol fuel has been used in the product carrier with established duel fuel engine, which has been greatly reducing emissions of $CO_2$, NOx and SOx from the engine. However, to use methanol alone as fuel oil in a general diesel engine, design modification of cylinder head is needed because the ignition aid device or the duel fuel injection system is needed. On the other hand, only if the mixer is installed on the fuel oil supply line, diesel oil - methanol blending oil can be used as fuel oil for the diesel engine, but there is a problem of the phase separation when two fuels are mixed. In this study, diesel oil and methanol were blended compulsorily in preventing the phase separation with installing agitators and a fuel oil boost pump on fuel line of a test engine. Also, cylinder pressure and fuel consumption quantity were measured according to engine load and methanol blending ratio, and indicated mean effective pressure, heat release rate and combustion temperature obtained from the single zone combustion model were analyzed to investigate the effects of latent heat of vaporization of methanol on combustion stability and characteristics. As a result, the combustion stability and characteristics of 10% methanol blending oil are closest to the those of diesel oil, and it could be used as fuel oil in existing diesel engines without deterioration of engine performance and combustion characteristics.

• Journal of the Korean Society of Safety
• /
• v.28 no.5
• /
• pp.5-9
• /
• 2013

Recently, eco-friendly sources of energy by fuel cells that use hydrogen as an energy source has emerged as the next generation of energy to solve the problem of environmental issues and exhaustion of energy. A solid oxide fuel cell(SOFC) classified based on the type of ion transfer mediator electrolyte has actively being researched. However, the reliability according to the thermal cycle is low during the operation of the fuel cell, and deformation problem comes from the difference in thermal expansion coefficient between the electrode material, the components made of ceramic material is also brittle, which means disadvantages in terms of the strength. Therefore, in this study, considering the states of the manufacturing and operating of SOFC single cells, the stress analyses in the each of the interfacial layer between the anode, electrolyte and the cathode were performed to get the basic data for reliability assessment of SOFC. The obtained results show that von Mises stress according to the thickness direction on operating state occurred maximum stress value in the electrolyte layer. And also the stresses inside the active area on a distance of 1 ${\mu}m$ from the electrode interface were estimated. Futhermore the evaluation was done for the variation of the stress according to the stage of the operation divided into three stages of manufacturing, stack, and operating.

• Nuclear Engineering and Technology
• /
• v.51 no.2
• /
• pp.410-423
• /
• 2019

Fire suppression using a water mist nozzle directly above an n-Heptane pool in a fire compartment with a door opening was numerically investigated using the Fire Dynamics Simulator (FDS) for the purpose of application in nuclear power plants. Input parameters for the numerical simulation were determined by experimental measurements. Water mist was activated 10 s after the fire began. The sensitivity analysis was conducted for three input parameters: total number of cubic cells of 6032-2,926,400, droplets per second of 1000-500,000, and extinguishing coefficient of 0-100. In a new simple calibration method of this study, the extinguishing coefficient yielding the fire suppression time closest to that measured by experiments was found for use as the FDS simulation input value. When the water mist jet flow made contact with the developed fire, the heat release rate instantaneously increased, and then rapidly decreased. This phenomenon occurred with a displacement of the flame near the liquid fuel pool. Changing the configuration of the door opening with different aspect ratios and opening ratios had impact on the maximum value of the heat release rate due to the flame displacement.

• Journal of the Korean Society of Systems Engineering
• /
• v.19 no.2
• /
• pp.46-58
• /
• 2023

Deterministic safety analysis is a crucial part of safety assessment, particularly when it comes to demonstrating the safety of nuclear power plant designs. The traditional approach to deterministic safety analysis models is to model the nuclear core using point kinetics. However, this simplified approach does not fully reflect the real core behavior with proper moderator and fuel reactivity feedbacks during the transient. The use of Multi-Physics approach allows more precise simulation reflecting the inherent three-dimensionality (3D) of the problem by representing the detailed 3D core, with instantaneous updates of feedback mechanisms due to changes of important reactivity parameters like fuel temperature coefficient (FTC) and moderator temperature coefficient (MTC). This paper addresses a CEA ejection accident at hot full power (HFP), in which the underlying strong and un-symmetric feedback between thermal-hydraulics and reactor kinetics exist. For this purpose, a multi-physics analysis tool has been selected with the nodal kinetics code, 3DKIN, implicitly coupled to the thermal-hydraulic code, RELAP5, for real-time communication and data exchange. This coupled approach enables high fidelity three-dimensional simulation and is therefore especially relevant to reactivity initiated accident (RIA) scenarios and power distribution anomalies with strong feedback mechanisms and/or un-symmetrical characteristics as in the CEA ejection accident. The Systems Engineering approach is employed to provide guidance in developing the work in a systematic and efficient fashion.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.54-64
• /
• 1992

During combustion process in a diesel engine radiation heat transfer is the same order of magnitude as the convection heat transfer. An approximation of heat and momentum source distributions is applied at a level consistent with those used in modelling the soot distribution and the turbulence instead of modelling the fuel spray and the chemical kinetics. This paper illustrates a use of the third order spherical harmonics approximation to the radiative transfer equation and delta-Eddington approximation to the scattering phase function for droplets in the flow. Results are obtained numerically by a time marching finite difference scheme. This study aims to compare heat transfer with convection heat transfer and to investigate the importance of scattering by fuel droplets and of accounting for spatial variations in the extinction coefficient on the radiative heat flux distributions at the walls of a disc shaped diesel engine.

• Advances in aircraft and spacecraft science
• /
• v.1 no.4
• /
• pp.409-425
• /
• 2014

Converging flows of a gas and a liquid at a microchannel cross junction, under proper conditions, can result in the formation of periodic, dispersed microslugs. This microslug formation phenomenon has been proposed as the basis for a fuel injection system in a novel, 'discrete' monopropellant microthruster designed for use in next-generation miniaturized satellites. Previous experimental studies demonstrated the ability to generate fuel slugs with characteristics commensurate with the intended application during steady-state operation. In this work, numerical and experimental techniques are used to study the effect of valve actuation on slug characteristics, and the results are used to compare with equivalent steady-state slugs. Computational simulations of a valve with a 1 ms valve-actuation cycle show that as the ratio of the response time of the valve to the fully open time is increased, transient effects can increase slug length by up to 17%. The simulations also demonstrate that the effect of the valve is largely independent of surface tension coefficient, which is the thermophysical parameter most responsible for slug formation characteristics. Flow visualization experiments performed using a miniature valve with a 20 ms response time showed less than a 1% change in the length of slugs formed during the actuation cycle. The results of this study indicate that impulse bit and thrust calculations can discount transient effects for slower valves, but as valve technology improves transient effects may become more significant.

• Journal of Biosystems Engineering
• /
• v.23 no.2
• /
• pp.147-156
• /
• 1998

It is desirable to use the renewable energy for the greenhouse heating in winter season, it make possible not only to save fossil fuel and conserve green environment but also to promote the quality of agricultural products and reduce the agricultural production cost. In this study the heat pump - PCM latent heat storage system has been developed to use the natural energy as much as possible for the thermal environment control of greenhouse. The coefficient of performance (COP) of the heat pump system was 3~4 with the ambient temperature ranging from 8$^{\circ}C$ to -8$^{\circ}C$, and greenhouse heating effect of the heat pump-PCM latent heat storage system on the basis of the ambient temperature was about 12-15$^{\circ}C$.