• Elastomers and Composites
• /
• v.56 no.4
• /
• pp.223-233
• /
• 2021

In this study, epoxidized liquid isoprene rubber (E-LqIR) was used as a processing aid in a silica-filled natural rubber compound to improve the fuel efficiency, abrasion resistance, and oil migration problems of truck and bus radial tire tread. The wear resistance, fuel efficiency, and extraction resistance of the compound were evaluated according to the molecular weight of E-LqIR. Results of the evaluation showed that the E-LqIR compound had a lower chemical crosslink density than that of a treated distillate aromatic extract (TDAE) oil compound because of the sulfur consumption of E-LqIR. However, the filler-rubber interaction improved because of the reaction of E-LqIR with silica and crosslink with the base rubber by sulfur. As the molecular weight of E-LqIR increased, crosslink with sulfur was facilitated, and the filler-rubber interaction improved, resulting in improved abrasion resistance. The fuel efficiency performance of the E-LqIR compound was poorer than that of the TDAE oil compound because of the low chemical crosslink density and hysteresis loss at the free chain end of E-LqIR. However, the fuel efficiency performance improved as the molecular weight of E-LqIR increased.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.1
• /
• pp.1-7
• /
• 2023

A fuel handling process combined with a pressure swing adsorption system (PSA) was simulated to produce pure hydrogen with a purity greater than 99.97%. The simulation consists of two parts. The fuel processing part consisting of reformer and water-gas shift reaction was simulated with Aspen plus^®, and the hydrogen purification part consisting of PSA was simulated with Aspen Adsorption^®. In this study, the effect of reformer temperature and pressure on the total hydrogen production yield was investigated. Simulations were performed over a temperature range of 700 to 1,000℃ and a pressure range of 1 to 10 bar. The total hydrogen production yield increased with increasing temperature and decreasing pressure. The maximum hydrogen yield was less than 50% in the simulation and will be lower in the real process.

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.106-108
• /
• 2005

The instrumented fuel irradiation test at a research reactor is needed to evaluate the performance of the developed nuclear fuel. The fuel elements can be designed to measure the center line temperature of fuel pellets during the irradiation test by using temperature sensor. The thermal sensor was composed of thermocouple and sensor sheath. Micro-laser welding technology was adopted to seal between seal tube and sensor sheath with thickness of 0.15 mm. The soundness of welding area has to be confirmed to prevent fission gas of the fuel from leaking out of the element during the fuel irradiation test. In this study, fundamental data for micro-laser welding technology was proposed to seal temperature sensor sheath of the instrumented fuel element. And, micro-laser welding for dissimilar metals between sensor sheath and seal tube was characterized by investigating welding conditions. Moreover, the micro-laser welding technology is closely related to advanced industry. It is expected that the laser material processing technology will be adopted to various a pplications in the industry.

• Nuclear Engineering and Technology
• /
• v.25 no.3
• /
• pp.424-429
• /
• 1993

Numeric characters are printed at the end part of nuclear fuel rod containing nuclear pellets. Fuel rods are discriminated and managed systematically by these characters in the process of producing fuel assembly. The characters are also used to examine manufacturing process of fuel rods in the survey of burnup efficiency as well as in inspection of irradiated fuel rod. Therefore automatic character recognition is one of the most important technologies in automatic manufacture of fuel assembly. In this study, character recognition system is developed. In the developed system, mesh feature extracted from each character written in the fuel rod has been compared with reference feature value stored in database, and the character is thus identified. In the result of experiment, 95.83 percent recognition rate is achievable.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.2
• /
• pp.155-162
• /
• 2016

A proton exchange membrane fuel cell (PEMFC) produces only water at cathode by an electrochemical reaction between hydrogen and oxygen. The generated water is transported across the membrane from the cathode to the anode. The transported water collected in water-trap and drained to the cathode within the humidifier outlet. If the condensate water is not being drained at the appropriate time, condensate water in the anode can cause the performance degradation or fuel efficiency degradation of fuel cell by the anode flooding or unnecessary hydrogen discharge. In this study, we proposed an optimization method of condensate water drain logic for the water drain performance and the water drain algorithm as considered the condensate water generating speed prep emergency case. In conclusion, we developed the water management strategy of fuel processing system (FPS) as securing fuel efficiency and operating stability.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2005.05a
• /
• pp.785-788
• /
• 2005

일정한 형태의 물체를 분석하기 위해 사용되는 각-거리 그래프를 이용하여 임의의 물체의 경계선 내부 영역의 면적을 측정하는 영상처리 알고리듬을 제안한다. 물체의 경계선 내부의 한 점을 중심으로 1차 각-거리 그래프를 생성하고 이 그래프로부터 거리 값이 급격히 변화하는 위치를 추출하여 1 차 그래프에서 접근하지 못한 영역을 인식하여 새 영역에서의 한 점을 중심으로 2 차 각-거리 그래프를 생성한다. 이와 같이 계층적으로 구성된 각-거리 그래프 그룹에 대해 거리의 제곱을 각도 방향으로 적분하여 물체의 경계선 내부 영역의 면적을 측정한다.

• Journal of ILASS-Korea
• /
• v.1 no.1
• /
• pp.55-62
• /
• 1996

In a fuel injection engine, atomization of liquid fuel and mixture formation process has influenced(or affected) directly on the engine performance and pollutant emission. In this study, the characteristics of fuel spray and the behaviors of secondary atomization developed at the downstream of the valves were investigated using an image processing method. Solid and perforated valves are chosen in order to evaluate the valve performance in terns of air flow rate, valve opening angle and valve shape. Experimental results clearly indicate that the spray atomization quality can be improved by increasing the perforated rat io and the blockage rat io in the perforated valve, the characteristics of spray atomization is improved by using the perforated valve with high perforated rat io and blockage ratio.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.04a
• /
• pp.203-206
• /
• 2005

The objective of study on composite cylinder for alternative fuel vehicle is to develop safe, efficient, and commercially viable, on-board fuel storage system for the fuel cell vehicle or natural gas vehicle that use highly compressed gaseous fuel such as hydrogen or natural gas. This study presents the whole procedure of development and certification of a type 3 composite cylinder of 207bar service pressure and 70 liter water capacity, which includes design/analysis, processing of filament winding, and validation through various testing and evaluation. Design methods of liner configuration and winding patterns are presented. Three dimensional, nonlinear finite element analysis techniques are used to predict burst pressure and failure mode. Design and analysis techniques are verified through burst and cycling tests. The full qualification test methods and results for validation and certification are presented.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1029_1030
• /
• 2009

본 논문에서는 빔 에너지를 이용하여 내 마모 및 내 부식성을 갖는 철망을 가공하여, 빔 에너지 조사 전과 후의 SEM 사진과 인장강도를 측정하여 비교, 분석 하였다. 전자빔으로 표면을 개질하기 전보다 후의 표면이 더 치밀해짐을 SEM사진을 통하여 볼 수 있었고, 인장강도를 측정 하여 개질 전과 후를 비교 하였는데, 인장강도와 관련된 탄성계수가 더 크게 나타나 전자빔 조사에 의한 샘플이 긴 수명을 갖는 요인이 분석되었다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.128-136
• /
• 1997

Spray characteristics of a fuel injector have an important effect upon engine power and emission. Thus this study was investigated the spray characteristics of the intermittent injection using a gasoline fuel injector. Image processing system and PDA system were utilized for visualization of a spray behavior and measurements of a droplet size and velocity, respectively. Fuel injection duration was fixed with 3ms and injection pressure was varied such as 250kPa, 300kPa, 350kPa. for a high fuel injection pressure, spray tip arrival time was fluctuated at a vigorously disintegrated cross section. Axial velocity was linear correlated with fuel droplet size in the time interval of an injected main spray at spray downstream.