• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.7 no.3
• /
• pp.353-358
• /
• 1995

The emission characteristics of a semi-Bunsen type burner for gas boilers were studied experimentally. The experimental results reveal that nitric oxide emission increases with fuel flow rate. It is linearly proportional to total fue flow rate at a small amount of fuel up to 0.4 liters per minute. It does not change significantly within the range of fuel flow rate from 0.4 to 1.2 liters per minute per nozzle and increases at large fuel flow rate. The carbon monoxide emission reveals to be dependent upon the fuel flow rate per each nozzle and the number of fuel injection nozzles. Diameter of an injection nozzle could have an effect on the emission characteristics of this type of burners. However, there is no marked change in the nitric oxide emission if the total fuel flow rate is same with different nozzle sizes.

• Journal of ILASS-Korea
• /
• v.17 no.2
• /
• pp.94-99
• /
• 2012

The characteristics of spray behavior and injected amount were studied with two types of nozzles for using in a compression ignition engine with dual fuel technology for construction machines. A penetration length of spray tends to shorten due to a decrease of injected amount of a diesel fuel with dual fuel engine application. In order to ignite the gaseous fuel premixed with air during intake process, a diesel fuel, which was compression ignited, needs to penetrate somehow similar depth compared with the case of a diesel fuel-only-injection. In this work, a nozzle with reduced hole diameter and increased number of holes was tested and demonstrated that, compared to diesel 100% case, its penetration lengths are comparable to 74% and 79%, respectively, of those of 100% and 50% supply of a diesel fuel with the baseline nozzle that has four holes and 30.4% increased diameter. This will presumably enhancement the combustion in a dual fuel engine. A design suggestion was also made in this work to achieve similar penetration length of spray with diesel 100% case to prevent combustion from being deteriorated in a dual fuel engine.

• Journal of ILASS-Korea
• /
• v.11 no.4
• /
• pp.251-265
• /
• 2006

To prevent the ozonosphere from being destroyed by Halon, it is an urgent task to find out Halon replacement. As one of the replacements water mist have showed broad applications by its advantages: little pollution to environment (not destroying the ozone layer or bring green house effect), extinguishing fire quickly, consuming a small quantity of water and having little damage to the protected objects. The methods of generating water mist strongly influence fire suppression effectiveness, which determine the cone angle, drop size distribution, flux uniformity, and momentum of the generating spray. The traditional water mist nozzle included pressure jet nozzles, impingement nozzles and twin-fluid nozzles. All of them have more or less disadvantages for fire suppression. Therefore, many research institutes and corporations are taking up with innovations in mist generation. This article provided some recent studies in State Key Laboratory of Fire Science (SKLFS) of University of Science and Technology of China. SKLFS have investigated new methods of generating water mist (i.e. effervescent atomization and ultrasonic atomization). and self developed a series of nozzles and developed advanced DPIVS (Digital Particle Image Velocimetry and Sizing) technique. Characteristics of water mist (the distribution of droplet sizes, flux density, spray dynamics and cone angle) produced by these nozzles were measured under different conditions (work pressure, nozzle geometry, etc.) using LDV/APV and DPTVS systems. A series of experiments were performed to study the fire suppression effectiveness in different fire scenario (different kindsof the fuel, fire size and ventilation conditions). The fire extinguishing mechanisms of water mist was also discussed.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2175-2180
• /
• 2008

Oxy-fuel combustion has been gaining its significance as a means of migrating the green house effects. Some experimental measurements were conducted to investigate the characteristics of oxy-fuel combustion and to aid a fundamental design of a lab-scale oxy-fuel combustor with a coaxial burner. CO emission was measured along the combustor centerline while combustion of methane and oxygen diluted by CO2 took place. Substitution of CO2 with N2 indicates a possibility that some CO is formed by dissociation of CO2. Some parametric tests were also performed to see the mixing effects of reactant gases on CO emission by changing the gas injection velocity at the burner nozzles with various heat loads. The overall results indicate that CO emission was reduced when the reactants are injected at higher velocities of similar magnitude.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.165.1-165.1
• /
• 2010

In the past, drivers bought a fuel additives to treat a combustion chambers or injector nozzles for carbon or gum deposit at market. But, nowadays, as raised cost of fuel for a vehicle the consumers also start focusing on a function of fuel additives that increases fuel economy of one. Some fuel additive manufacturers and agents advertise that their goods make a car it's initial state. This paper shows data for 3 years that were acquired during test for registration of an additive in domestic. The data were sorted according to kind of vehicle, kind of fuel, test mode, CO, HC, NOx, PM, total emission, fuel economy and accumulated mileage. And than by using simple linear regression analysis changes according to accumulated mileage was displayed. Normal distribution and histogram of rate of increase and decrease were displayed. the analyzed data indicated that a fuel additive maintain and make a car the first state of one but can't make a car be batter than initial the one.

• Journal of Energy Engineering
• /
• v.7 no.1
• /
• pp.17-23
• /
• 1998

A simplified experiment was performed to figure out the atomization characteristics of highly viscous liquid of rice-bran oil by applying ultrasonic energy to improve the atomization of spray droplets. A spray system, an ultrasonic system, and three kinds of pintle-type nozzles(pin-edge angle: 5 , 10 , 15 ) were manufactured. To investigate the effects of ultrasonic energy on the atomization of a highly viscous liquid, a phase doppler particle analyzer was used for the measurement and calculation of spray droplets data. Nozzle opening pressures were chosen of 3 levels, i.e, 10, 13, 16 MPa. As a result, it could be concluded that the ultrasonic energy was effective to improve the spray atomization when applied to the fuel by means of 3 different nozzles because of the effects of the liquid fuel cavitation and relaxation between molecules caused by ultrasonic energy. The improvement rate of the spray atomization by the ultrasonic spray atomization by the ultrasonic spray compared with the conventional spray was about 10% increase in the case of pintle type nozzles. With the increase of pin-edge angles the distribution lines by nozzle opening pressures are declined for both conventional and ultrasonic sprays. This means that the increase of the pin-edge angle improves the atomization of sprays.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.12
• /
• pp.1635-1646
• /
• 1997

The nozzle length to diameter ratio of real diesel nozzles is about 2-8 which is not long enough for a fully developed and stabilized flow. The characteristics of the flow such as turbulence at the nozzle exit which affect the development of the spray can be enhanced by impinging the flow inside nozzle. The flow details inside the impinging nozzles have been investigated both experimentally and numerically. The mean velocities, the fluctuating velocities, and discharge coefficients in the impinging inlet nozzles, round inlet nozzle, and sharp inlet nozzle were obtained at various Reynolds number. The developing feature of the external spray were photographed by still camera and the droplet sizes and velocities were also measured by laser Doppler technique. The spray angle was greater and the droplet sizes near the spray axis were smaller with the impinging flow inside nozzle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.127-134
• /
• 2004

Three-dimensional numerical investigations are carried out to understand the combustion characteristics inside a DLN(dry low NOx) utility gas turbine combustor during the combustion mode change period by applying transient fuel flow rates in fuel supply system as numerical boundary conditions. The numerical solution domain comprises the complex combustor liner including cooling air holes, three types of fuel nozzles, a swirl vane, and a venturi. Detailed three-dimensional flow and temperature fields before and after combustion mode changeover have been analyzed. The results may be useful for further studies on the unfavorable phenomena, such as flashback or thermal damage of combustor parts when the combustion mode changes.

• Journal of ILASS-Korea
• /
• v.8 no.3
• /
• pp.27-32
• /
• 2003

It is important to improve the efficiency of the existing small scale burner which used in agricultural product dry system and gardening dry system. In order to economize fuel Consumption and decrease the exhaust emission especially $CO_2$, the better design for the small scale burner is needed. Spray characteristics are the essential element for the design. Macroscopic spray characteristics such as spray angle and breakup length were measured. SMD which is contained the Microscopic spray characteristics was measured too. SMD was measured at 8mm, I2mm, I6mm downstream of the nozzle tip for both Hago and Danfoss nozzles by the Malvern Particle Sizer.

• Journal of ILASS-Korea
• /
• v.9 no.1
• /
• pp.1-7
• /
• 2004

This paper describes the characteristics of injection rate and macroscopic behavior of fuel spray injected from common-rail type diesel injectors with different nozzle geometries. The injection rates according to the nozzle geometries were measured at different energizing duration of the injector solenoid and injection pressure by using the Bosch's injection rate meter based on the pressure variation in the tube. The spray behaviors injected from the different nozzles were visualized using the spray visualization system composed of an Ar-ion laser, an ICCD camera, and a synchronization system at various injection and ambient pressures. It is revealed that VCO nozzle has higher spray tip velocity at the early stage of injection duration and wider spray cone angle than the mini-sac nozzles. Also the spray cone angle is increased with the increase of nozzle diameter.