• 대한기계학회논문집A
• /
• 제34권7호
• /
• pp.843-850
• /
• 2010

지지격자체는 경수로 핵연료집합체의 가장 중요한 핵심 구조부품이다. 지지격자체 설계시의 고려사항은 원자로 운전중에 연료봉의 지지건전성을 유지하도록 하는 것이다. 본 연구에서는 연료봉이 유동기인진동에 의해서 진동할 때 연료봉과 연료봉 지지부 사이에서 상대변위를 완화해 줌으로서 연료봉의 프레팅 마모손상 가능성을 감소시킬 수 있는 이동 가능한 연료봉 지지부로 구성된 새로운 지지격자체 형상을 제안하였다. 아울러 제안된 이동 가능 지지부의 연료봉 지지특성을 유한요소해석을 통해 분석하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.82-87
• /
• 2003

Nuclear fuel with a big slenderness ratio is susceptible to flow-induced vibration under very severe conditions of high temperature, high flow and exposure to irradiation in nuclear reactor. The fuel assembly should, therefore, be designed to escape any resonance due to the vibration during the reactor operation, in particular, in case of the design changes. In addition, the amplitudes due to the grid vibration, the fuel rod vibration and the fuel assembly vibration should be minimized to reduce the grid-to-rod fretting wear. Fuel assembly vibration tests in air at room temperature and in water at high temperature have been performed to investigate fuel vibration behaviors. The frequency and damping during the test in air have been compared to those in water. Through the hydraulic test, the advanced assembly has been evaluated not to be susceptible to any resonance. In addition, the test data from the tests can be used to make fuel model and to evaluate grid-to-rod fretting wear.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.256-261
• /
• 2004

To evaluate the effect of spring shape on the fretting wear of nuclear fuel rod, sliding wear tests were performed using three kinds of space grid springs in room temperature air and water. With increasing slip amplitude, wear volume of each spring gradually increased. It is apparently shown that spring with convex shape had a relatively high wear resistance compared with concave shape springs. It is suggested that the ratio of the wear volume to the worn area can be suggested as an efficient and valid parameter to evaluate the wear resistibility of a fuel grid spring.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 추계학술발표회
• /
• pp.284-285
• /
• 2005

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2004년도 추계학술발표회 발표논문집
• /
• pp.833-834
• /
• 2004

• Tribology and Lubricants
• /
• 제22권3호
• /
• pp.144-148
• /
• 2006

The experimental investigation was performed to find the associated changes in characteristics of fretting wear with various water temperatures. The fretting wear tests were carried out using the zirconium alloy tubes and the grids with increasing the water temperature. The tube materials in water of $20^{\circ}C,\;50^{\circ}C\;and\;80^{\circ}C$ were tested with the applied load of 20 N and the relative amplitude of $200{\mu}m$. The worn surfaces were observed by SEM, EDX analysis and 2D surface profiler. As the water temperature increased, the wear volume was decreased, but oxide layer was increased on the worn surface. The abrasive wear mechanism was observed at water temperature of $20^{\circ}C$ and adhesive wear mechanism occurred at water temperature of $50^{\circ}C,\;80^{\circ}C$. As the water temperature increased, surface micro-hardness was decreased, but wear depth and wear width were decreased due to increasing stick phenomenon. Stick regime occurred due to the formation of oxide layer on the worn surface with increasing water temperatures

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.73-79
• /
• 2002

상온 공기분위기에서 두 가지 형태의 스프링에 대한 연료봉 피복관의 마멸실험을 수행하였으며 다음과 같은 결론을 얻었다. (1) 가장 큰 마멸부피는 스프링 형상이 오목할 경우 틈이 존재할 때 발생하였으며, 형상이 볼록한 경우에는 접촉하중이 존재할 때 마멸부피가 크게 나타났다. (2) 접촉형상이 오목한 형태로 연료봉을 감싸고 있는 경우, 마멸입자의 방출은 다소 어렵게 되며 이에 따라 마열거동은 표면에서 생성되는 마멸입자가 외부로 방출되는 용이성에 따라 최종적으로 마멸부피는 결정된다. (3) 볼록한 형상의 스프링의 경우, 충격마모에 대하여 저항성을 보였으나, 접촉하중이 존재할 경우 높은 마멸량을 보이고 있다. (4) 오목한 형태의 스프링 조건에서 축 방향의 마멸보다는 횡 방향의 마멸량이 더 낮게 나타났다. 이것의 주된 원인은 오목한 형태의 스프링이 충격하중에 있어 가이드역할을 할 가능성이 있는 것으로 나타났다. 또한, 양 방향 모두 마멸입자의 고착 흔적이 나타났으나 횡 방향의 경우 연삭에 의한 경향이 보다 뚜렷이 나타났다.

• Tribology and Lubricants
• /
• 제22권1호
• /
• pp.8-13
• /
• 2006

Sliding wear tests have been performed to evaluate the effect of normal load decrease on the wear depth of nuclear fuel rods in room temperature air. The objectives of this study are to quantitatively evaluate the supporting ability of spacer grid springs, to estimate the wear depth by using the contacting force decrease and to compare the wear behavior with increasing test cycles (up to $10^7$) at each spring condition. The result showed that the contacting load decrease depends on the spring shape and the applied slip amplitude. The estimated wear depth is smaller when compared with measured wear depth. Based on the test results, the wear mechanism, the role of wear debris layer and the spring shape effect were discussed.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.828-835
• /
• 2006

Spacer grid springs support the fuel rods in a nuclear fuel system. The spacer grid is a part of a fuel assembly. Since a spring has repeated contacts with the fuel rod, fretting wear occurs on the surface of the spring. Design is usually performed to reduce the wear. The conceptual design process for the spring is defined by using the Independence of axiomatic design and the design is carried out based on the direction that the design matrix indicates. For detailed design an optimization problem is formulated. In optimization, homologous design is employed to reduce fretting wear. The deformation of a structure is called homologous if a given geometrical relationship holds for a given number of structural points before, during, and after the deformation. In this case, the deformed shape of the spring should be the same as that of the fuel rod. 1bis condition is transformed to a function and considered as a constraint in the optimization process. The objective function is minimizing the maximum stress to allow a local plastic deformation. Optimization results show that the contact occurs in a wide range. Also, the results are verified by nonlinear finite element analysis.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.41-49
• /
• 2003

Tube oscillation behaviour is experimentally investigated for the study on the fuel rod fretting that is caused by the flow-induced vibration in nuclear reactor. The experiment was conducted in all at room temperature. The specimen of tube assembly was supported by plate springs which simulated the spacer grids and fuel rods of a fuel assembly. To investigate the influence of contact condition between the grids and rods, normal load of 10 and 5 N, gaps of 0.1 and 0.3 mm were applied. The range of the oscillation at the center of the fuel rod specimen was varied as 0.2, 0.3 and 0.4 mm to simulate the fuel rod vibration due to flow. Displacements near the contact were measured with four displacement sensors during the tube oscillation. As results, the shape of oscillation (phase) varied depending on the contact condition. The oscillation displacement increased considerably from the contact to gap condition. The displacement increased further as the gap size increased. It is regarded that the spring shape influences the tube oscillation behaviour. Simple calculation showed that the slip displacement was very small. Therefore, cumulative damage concept is necessary for the fuel rod wear. The mechanism of plowing is thought required to explain the severe wear in the case of gap existence.