• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.1133-1134
• /
• 2013

• 대한기계학회논문집B
• /
• 제35권2호
• /
• pp.121-127
• /
• 2011

희박 공연비에서 동작하는 디젤 엔진은 NOx 를 저감시키기 위해서 주기적으로 과농한 분위기를 형성해 주어야 한다. 최근 배기관 내에 환원제로서 경유를 직접 분사하는 HC-LNT 방식이 활발히 연구되고 있다. 이러한 연구는 NOx 저감을 위해 HC 의 농도를 제어하는 기술로서, 실제 배기관내에 HC 가 균일하게 분포하여야 촉매의 정화효율이 향상되므로 HC 를 균일하게 분사하는 방법의 최적화가 가장 중요하다. 본 연구에서는 저압에서 미립화 특성이 양호한 가솔린 흡기포트 분사용 인젝터를 이용하여, 가시화 방법으로 실제 배기관내에서의 환원제 분무 거동 특성을 측정하였고 NOx 정화 특성간의 관계를 실험적으로 비교함으로써, 인젝터의 최적 부착 조건과 분사 조건을 파악하였다.

• Environmental Engineering Research
• /
• 제11권3호
• /
• pp.149-155
• /
• 2006

NOx reduction experiments were conducted by direct injection of urea into a diesel fueled, combustion-driven flow reactor which simulated a single engine cylinder ($966cm^3$). NOx reduction tests were carried out over a wide range of air/fuel ratios (A/F=20-40) using an initial NOx level of 530ppm, and for normalized stoichiometric ratios of reductant to NOx (NSR) of 1.5 to 4.0. The results show that effective NOx reduction with urea occurred over an injection temperature range of 1100 to 1350K. NOx reduction increased with increasing NSR values, and about a 40%-60% reduction of NOx was achieved with NSR=1.5-4.0. Most of the NOx reduction occurred within the cylinder and head section (residence time <40msec), since temperatures in the exhaust pipe were too low for additional NOx reduction. Relatively low NOx reduction is believed to be due to the existence of higher levels of CO and unburned hydrocarbons (UHC)inside the cylinder, and large temperature drops along the reactor. Injection of secondary combustible additives (diesel fuel/$C_2H_6$) into the exhaust pipe promoted further substantial NOx reduction (5%-30%) without shifting the temperature windows. Diesel fuel was found to enhance NOx reduction more than $C_2H_6$, and finally practical implications are further discussed.

• 한국수소및신에너지학회논문집
• /
• 제8권1호
• /
• pp.23-29
• /
• 1997

The combustion and smoke emission of an indirect injection diesel engine Were investigated running the engine on Hydrogen/diesel fuels. Hydrogen fuel supplied to the intake pipe was varied 0 to 10 percent of DF2' s heating value. The most inportant finding was that the smoke emission is not decreased with increase of hydrogen fuel supplement. Also, the ignition delay is almost negligible over 10 percent hydrogen fuel mixture.

• 소성∙가공
• /
• 제19권2호
• /
• pp.88-94
• /
• 2010

The next generation of diesel engine can operate at high injection pressure up to 1,800bar. The common rail pipe must have higher internal strength because it is directly influenced by the high-pressure fuel. Folding defects in the Common rail pipe can not ensure the structural safety. Therefore, Preform design and fatigue-life analysis are very important for preventing the head of the common rail pipe from folding in the heading process and for predicting fatigue life according to the amount of folding. In this study, a closed form equation to predict fatigue life was suggested by Goodman theory and pressure vessels theory in ASME Code in order to develop an optimization technique of the heading process and verified its reliability through fatigue-structural coupled field analysis. The results calculated by the theory were in good agreement with those obtained by the finite element analysis.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.65-72
• /
• 2011

In this study, the numbers, sizes of particles from a single cylinder direct injection spark-ignition (DISI) engine fuelled with gasoline and LPG are examined over a wide range of engine operating conditions. Tests are conducted with various engine loads (2~10bar of IMEP) and fuel injection pressures (60, 90, and 120 bar) at the engine speed of 1,500 rpm. Particles are sampled directly from the exhaust pipe using rotating disk thermodiluter. The size distributions are measured using a scanning mobility particle sizer (SMPS) and the particle number concentrations are measured using a condensation particle counter (CPC). The results show that maximum brake torque (MBT) timing for LPG fuel is less sensitive to engine load and its combustion stability is also better than that for gasoline fuel. The total particle number concentration for LPG was lower by a factor of 100 compared to the results of gasoline emission due to the good vaporization characteristic of LPG. Test result presents that LPG for direct injection spark ignition engine help the particle emission level to reduce.

• 한국가스학회지
• /
• 제20권4호
• /
• pp.1-6
• /
• 2016

버스와 같은 대형 차량에서 사용되는 대형 CNG 엔진에는 가스 연료 분사를 위한 인젝터가 6개 가량의 단위로 모듈 형태를 구성하고 있다. 이러한 인젝터 모듈은 연료 공급을 위한 입출구가 각각 한 곳으로 구성되어 있으며 쓰로틀 후단을 통하여 흡기관으로 연료를 공급하는 방식이므로 과도 운전에 대한 응답성이 매우 낮은 구조를 형성하고 있다. 본 연구에서는 이러한 인젝터 모듈의 내부 유로에 대한 유동 해석을 통하여 응답성을 개선할 수 있는 방안을 제시하고자 한다. 결론에 따르면 내부 유로의 체적을 감소시킴으로써 가스 연료의 공급 응답성을 개선할 수 있었고, 각각의 인젝터에서 모듈의 출구까지의 거리를 동일하게 하는 방안도 응답성과 연료 공급량의 선형성을 확보할 수 있는 것을 확인하였다. 다만 각 인젝터의 분사 순서 시기에는 큰 영향을 받지 않는 결과를 보였다.

• 한국정밀공학회지
• /
• 제27권1호
• /
• pp.25-32
• /
• 2010

With the latest automobile technology, though the third generation common rail system requires high injection pressures up to 1,800bar, the next generation diesel engine is expected to require more higher pressures than the third generation. The common rail pipe requires higher strength because it is one of the parts in the common rail system, which is influenced directly by fuel under high pressure. Preform design is very important for preventing head of the common rail pipe from folding in the heading process. In this study, die angle, curvature, outer diameter of die and length of trapped part are selected as main parameters to obtain best preform shape minimizing radius of folding. Therefore optimal design is carried out by finite element analysis and Taguchi method through main parameters. Results of the finite element analysis have good agreements with those of the experiments in the actual field.

• 한국자동차공학회논문집
• /
• 제21권6호
• /
• pp.117-122
• /
• 2013

This study is aimed to develop LNT(Lean NOx Trap) aftertreatment system for DME engine. Modified DME engine, which was changed from diesel to current DME engine, is used for this research and is equipped with common rail type injector and fuel supplying system. LNT system has reductant injector. DME is also used as reduction agent. For this research, reduction agent injection time width and interval were varied. And also, swirler was used to improve homogeneity of reducing agent in exhaust pipe. The reduction rate of NOx by LNT was increased by longer injection width, short interval and swirler. The maximum diminution of NOx by LNT was over 85%.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2000년도 제21회 KOSCO SYMPOSIUM 논문집
• /
• pp.202-211
• /
• 2000

Characteristics of the fuel injection and entrainment of the primary air of gas burner have been investigated. Primary air flow rates that entrained by gas streams play major role to control the performance of the partially premixed combustion. Pressure distributions of mixing tube assembly are studied as major parameter for increasing the primary air flow rates. Buoyancy-effect burner is proposed as one alternative to improve the pressure distribution. Buoyancy effect caused by metal ring placed around the flame holes reduces pressure of the entrance of the mixing tube and that, entrained air flow rates are increased.